ARM: dts: omap34xx & omap36xx: replace opp-v1 tables by opp-v2 for

With the driver installed, we can change the opp-v1 table format
to opp-v2.

In addition, move omap3 from whitelist to blacklist in cpufreq-dt-platdev
in the same patch, because doing either first breaks operation and
may make trouble in bisect.

We also can remove opp-v1 table for omap3-n950-n9 since its 1GHz
capability is now automatically detected.

We also fix a wrong OPP4 voltage for omap3430 which must be
0.6V + 54*12.5mV = 1275mV. Otherwise the twl4030 driver will reject
this OPP.

Note: the high speed OPPs that were not available in the opp-v1 tables
are tagged "turbo-mode;" which means they are not automatically
activated by the govenors or cpu-freq.

To enable you have to write

echo 1 >/sys/devices/system/cpu/cpufreq/boost

Note: to hard disable an OPP in a board.dts file use e.g.

&cpu0_opp_table: {
	/delete-node/ opp1g-1000000000;	/* do not use */
};

or alternatively:

&cpu0_opp_table: {
	opp1g-1000000000 {
		status = "disabled";	/* do not use */
	};
};
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>

arch/arm/boot/dts/omap3-n950-n9.dtsi

@@ -11,13 +11,6 @@ / {
 	cpus {
 		cpu@0 {
 			cpu0-supply = <&vcc>;
-			operating-points = <
-				/* kHz    uV */
-				300000  1012500
-				600000  1200000
-				800000  1325000
-				1000000	1375000
-			>;
 		};
 	};
 

arch/arm/boot/dts/omap34xx.dtsi

@@ -16,19 +16,67 @@
 / {
 	cpus {
 		cpu: cpu@0 {
-			/* OMAP343x/OMAP35xx variants OPP1-5 */
-			operating-points = <
-				/* kHz    uV */
-				125000   975000
-				250000  1075000
-				500000  1200000
-				550000  1270000
-				600000  1350000
-			>;
+			/* OMAP343x/OMAP35xx variants OPP1-6 */
+			operating-points-v2 = <&cpu0_opp_table>;
+
 			clock-latency = <300000>; /* From legacy driver */
 		};
 	};
 
+	/* see Documentation/devicetree/bindings/opp/opp.txt */
+	cpu0_opp_table: opp-table {
+		compatible = "operating-points-v2-ti-cpu";
+		syscon = <&scm_conf>;
+
+		opp1-125000000 {
+			opp-hz = /bits/ 64 <125000000>;
+			/*
+			 * we currently only select the max voltage from table
+			 * Table 3-3 of the omap3530 Data sheet (SPRS507F).
+			 * Format is: <target min max>
+			 */
+			opp-microvolt = <975000 975000 975000>;
+			/*
+			 * first value is silicon revision bit mask
+			 * second one 720MHz Device Identification bit mask
+			 */
+			opp-supported-hw = <0xffffffff 3>;
+		};
+
+		opp2-250000000 {
+			opp-hz = /bits/ 64 <250000000>;
+			opp-microvolt = <1075000 1075000 1075000>;
+			opp-supported-hw = <0xffffffff 3>;
+			opp-suspend;
+		};
+
+		opp3-500000000 {
+			opp-hz = /bits/ 64 <500000000>;
+			opp-microvolt = <1200000 1200000 1200000>;
+			opp-supported-hw = <0xffffffff 3>;
+		};
+
+		opp4-550000000 {
+			opp-hz = /bits/ 64 <550000000>;
+			opp-microvolt = <1275000 1275000 1275000>;
+			opp-supported-hw = <0xffffffff 3>;
+		};
+
+		opp5-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <1350000 1350000 1350000>;
+			opp-supported-hw = <0xffffffff 3>;
+		};
+
+		opp6-720000000 {
+			opp-hz = /bits/ 64 <720000000>;
+			opp-microvolt = <1350000 1350000 1350000>;
+			/* only high-speed grade omap3530 devices */
+			opp-supported-hw = <0xffffffff 2>;
+			turbo-mode;
+		};
+	};
+
 	ocp@68000000 {
 		omap3_pmx_core2: pinmux@480025d8 {
 			compatible = "ti,omap3-padconf", "pinctrl-single";

arch/arm/boot/dts/omap36xx.dtsi

@@ -19,15 +19,53 @@ aliases {
 	};
 
 	cpus {
-		/* OMAP3630/OMAP37xx 'standard device' variants OPP50 to OPP130 */
+		/* OMAP3630/OMAP37xx variants OPP50 to OPP130 and OPP1G */
 		cpu: cpu@0 {
-			operating-points = <
-				/* kHz    uV */
-				300000  1012500
-				600000  1200000
-				800000  1325000
-			>;
-			clock-latency = <300000>; /* From legacy driver */
+			operating-points-v2 = <&cpu0_opp_table>;
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
+		};
+	};
+
+	/* see Documentation/devicetree/bindings/opp/opp.txt */
+	cpu0_opp_table: opp-table {
+		compatible = "operating-points-v2-ti-cpu";
+		syscon = <&scm_conf>;
+
+		opp50-300000000 {
+			opp-hz = /bits/ 64 <300000000>;
+			/*
+			 * we currently only select the max voltage from table
+			 * Table 4-19 of the DM3730 Data sheet (SPRS685B)
+			 * Format is: <target min max>
+			 */
+			opp-microvolt = <1012500 1012500 1012500>;
+			/*
+			 * first value is silicon revision bit mask
+			 * second one is "speed binned" bit mask
+			 */
+			opp-supported-hw = <0xffffffff 3>;
+			opp-suspend;
+		};
+
+		opp100-600000000 {
+			opp-hz = /bits/ 64 <600000000>;
+			opp-microvolt = <1200000 1200000 1200000>;
+			opp-supported-hw = <0xffffffff 3>;
+		};
+
+		opp130-800000000 {
+			opp-hz = /bits/ 64 <800000000>;
+			opp-microvolt = <1325000 1325000 1325000>;
+			opp-supported-hw = <0xffffffff 3>;
+		};
+
+		opp1g-1000000000 {
+			opp-hz = /bits/ 64 <1000000000>;
+			opp-microvolt = <1375000 1375000 1375000>;
+			/* only on am/dm37x with speed-binned bit set */
+			opp-supported-hw = <0xffffffff 2>;
+			turbo-mode;
 		};
 	};
 

drivers/cpufreq/cpufreq-dt-platdev.c

@@ -86,7 +86,6 @@ static const struct of_device_id whitelist[] __initconst = {
 	{ .compatible = "st-ericsson,u9540", },
 
 	{ .compatible = "ti,omap2", },
-	{ .compatible = "ti,omap3", },
 	{ .compatible = "ti,omap4", },
 	{ .compatible = "ti,omap5", },
 
@@ -137,6 +136,7 @@ static const struct of_device_id blacklist[] __initconst = {
 	{ .compatible = "ti,am33xx", },
 	{ .compatible = "ti,am43", },
 	{ .compatible = "ti,dra7", },
+	{ .compatible = "ti,omap3", },
 
 	{ }
 };