Merge tag 'omap-for-v5.5/soc-late-signed' into omap-for-v5.5/ti-sysc-late

Few late SoC changes for v5.5 merge window

These changes just clean up few typos, and there is one non-critical
correction of missing put_device() after calling of_platform_populate()
for display controller.

Naturally none of this is urgent and can be merged when suitable.

arch/arm/boot/dts/am335x-icev2.dts

@@ -432,7 +432,7 @@ &mmc1 {
 	pinctrl-0 = <&mmc0_pins_default>;
 };
 
-&gpio0 {
+&gpio0_target {
 	/* Do not idle the GPIO used for holding the VTT regulator */
 	ti,no-reset-on-init;
 	ti,no-idle-on-init;

arch/arm/boot/dts/am33xx-l4.dtsi

@@ -127,7 +127,7 @@ target-module@5000 {			/* 0x44e05000, ap 12 30.0 */
 			ranges = <0x0 0x5000 0x1000>;
 		};
 
-		target-module@7000 {			/* 0x44e07000, ap 14 20.0 */
+		gpio0_target: target-module@7000 {	/* 0x44e07000, ap 14 20.0 */
 			compatible = "ti,sysc-omap2", "ti,sysc";
 			reg = <0x7000 0x4>,
 			      <0x7010 0x4>,
@@ -2026,7 +2026,9 @@ target-module@e000 {			/* 0x4830e000, ap 72 4a.0 */
 			reg = <0xe000 0x4>,
 			      <0xe054 0x4>;
 			reg-names = "rev", "sysc";
-			ti,sysc-midle ;
+			ti,sysc-midle = <SYSC_IDLE_FORCE>,
+					<SYSC_IDLE_NO>,
+					<SYSC_IDLE_SMART>;
 			ti,sysc-sidle = <SYSC_IDLE_FORCE>,
 					<SYSC_IDLE_NO>,
 					<SYSC_IDLE_SMART>;

arch/arm/boot/dts/am3874-iceboard.dts

@@ -111,13 +111,13 @@ pca9548@70 {
 		reg = <0x70>;
 		#address-cells = <1>;
 		#size-cells = <0>;
+		i2c-mux-idle-disconnect;
 
 		i2c@0 {
 			/* FMC A */
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <0>;
-			i2c-mux-idle-disconnect;
 		};
 
 		i2c@1 {
@@ -125,7 +125,6 @@ i2c@1 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <1>;
-			i2c-mux-idle-disconnect;
 		};
 
 		i2c@2 {
@@ -133,7 +132,6 @@ i2c@2 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <2>;
-			i2c-mux-idle-disconnect;
 		};
 
 		i2c@3 {
@@ -141,7 +139,6 @@ i2c@3 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <3>;
-			i2c-mux-idle-disconnect;
 		};
 
 		i2c@4 {
@@ -149,14 +146,12 @@ i2c@4 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <4>;
-			i2c-mux-idle-disconnect;
 		};
 
 		i2c@5 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <5>;
-			i2c-mux-idle-disconnect;
 
 			ina230@40 { compatible = "ti,ina230"; reg = <0x40>; shunt-resistor = <5000>; };
 			ina230@41 { compatible = "ti,ina230"; reg = <0x41>; shunt-resistor = <5000>; };
@@ -182,14 +177,12 @@ i2c@6 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <6>;
-			i2c-mux-idle-disconnect;
 		};
 
 		i2c@7 {
 			#address-cells = <1>;
 			#size-cells = <0>;
 			reg = <7>;
-			i2c-mux-idle-disconnect;
 
 			u41: pca9575@20 {
 				compatible = "nxp,pca9575";

arch/arm/boot/dts/am4372.dtsi

@@ -336,6 +336,8 @@ dispc: dispc@4832a400 {
 				ti,hwmods = "dss_dispc";
 				clocks = <&disp_clk>;
 				clock-names = "fck";
+
+				max-memory-bandwidth = <230000000>;
 			};
 
 			rfbi: rfbi@4832a800 {

arch/arm/boot/dts/dra7-l4.dtsi

@@ -2729,7 +2729,7 @@ mcasp1: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 129 1>, <&edma_xbar 128 1>;
 				dma-names = "tx", "rx";
-				clocks = <&ipu_clkctrl DRA7_IPU_MCASP1_CLKCTRL 22>,
+				clocks = <&ipu_clkctrl DRA7_IPU_MCASP1_CLKCTRL 0>,
 					 <&ipu_clkctrl DRA7_IPU_MCASP1_CLKCTRL 24>,
 					 <&ipu_clkctrl DRA7_IPU_MCASP1_CLKCTRL 28>;
 				clock-names = "fck", "ahclkx", "ahclkr";
@@ -2765,8 +2765,8 @@ mcasp2: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 131 1>, <&edma_xbar 130 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP2_CLKCTRL 22>,
-					 <&l4per2_clkctrl DRA7_L4PER2_MCASP2_CLKCTRL 24>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP2_CLKCTRL 0>,
+					 <&ipu_clkctrl DRA7_IPU_MCASP1_CLKCTRL 24>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP2_CLKCTRL 28>;
 				clock-names = "fck", "ahclkx", "ahclkr";
 				status = "disabled";
@@ -2783,9 +2783,8 @@ target-module@68000 {			/* 0x48468000, ap 13 26.0 */
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 28>;
-			clock-names = "fck", "ahclkx", "ahclkr";
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>;
+			clock-names = "fck", "ahclkx";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x68000 0x2000>,
@@ -2801,7 +2800,7 @@ mcasp3: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 133 1>, <&edma_xbar 132 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP3_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";
@@ -2818,9 +2817,8 @@ target-module@6c000 {			/* 0x4846c000, ap 15 2e.0 */
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 24>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 28>;
-			clock-names = "fck", "ahclkx", "ahclkr";
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 24>;
+			clock-names = "fck", "ahclkx";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x6c000 0x2000>,
@@ -2836,7 +2834,7 @@ mcasp4: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 135 1>, <&edma_xbar 134 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP4_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";
@@ -2853,9 +2851,8 @@ target-module@70000 {			/* 0x48470000, ap 19 36.0 */
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 24>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 28>;
-			clock-names = "fck", "ahclkx", "ahclkr";
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 24>;
+			clock-names = "fck", "ahclkx";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x70000 0x2000>,
@@ -2871,7 +2868,7 @@ mcasp5: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 137 1>, <&edma_xbar 136 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP5_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";
@@ -2888,9 +2885,8 @@ target-module@74000 {			/* 0x48474000, ap 35 14.0 */
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 24>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 28>;
-			clock-names = "fck", "ahclkx", "ahclkr";
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 24>;
+			clock-names = "fck", "ahclkx";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x74000 0x2000>,
@@ -2906,7 +2902,7 @@ mcasp6: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 139 1>, <&edma_xbar 138 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP6_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";
@@ -2923,9 +2919,8 @@ target-module@78000 {			/* 0x48478000, ap 39 0c.0 */
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 24>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 28>;
-			clock-names = "fck", "ahclkx", "ahclkr";
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 24>;
+			clock-names = "fck", "ahclkx";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x78000 0x2000>,
@@ -2941,7 +2936,7 @@ mcasp7: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 141 1>, <&edma_xbar 140 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP7_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";
@@ -2958,9 +2953,8 @@ target-module@7c000 {			/* 0x4847c000, ap 43 04.0 */
 					<SYSC_IDLE_SMART>;
 			/* Domains (P, C): l4per_pwrdm, l4per2_clkdm */
 			clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 0>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 24>,
-				 <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 28>;
-			clock-names = "fck", "ahclkx", "ahclkr";
+				 <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 24>;
+			clock-names = "fck", "ahclkx";
 			#address-cells = <1>;
 			#size-cells = <1>;
 			ranges = <0x0 0x7c000 0x2000>,
@@ -2976,7 +2970,7 @@ mcasp8: mcasp@0 {
 				interrupt-names = "tx", "rx";
 				dmas = <&edma_xbar 143 1>, <&edma_xbar 142 1>;
 				dma-names = "tx", "rx";
-				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 22>,
+				clocks = <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 0>,
 					 <&l4per2_clkctrl DRA7_L4PER2_MCASP8_CLKCTRL 24>;
 				clock-names = "fck", "ahclkx";
 				status = "disabled";

arch/arm/boot/dts/logicpd-torpedo-som.dtsi

@@ -192,3 +192,7 @@ twl_power: power {
 &twl_gpio {
 	ti,use-leds;
 };
+
+&twl_keypad {
+	status = "disabled";
+};

arch/arm/boot/dts/omap3-gta04.dtsi

@@ -124,6 +124,7 @@ lcd: td028ttec1@0 {
 			spi-max-frequency = <100000>;
 			spi-cpol;
 			spi-cpha;
+			spi-cs-high;
 
 			backlight= <&backlight>;
 			label = "lcd";

arch/arm/boot/dts/omap4-droid4-xt894.dts

@@ -369,7 +369,7 @@ wlcore: wlcore@2 {
 		compatible = "ti,wl1285", "ti,wl1283";
 		reg = <2>;
 		/* gpio_100 with gpmc_wait2 pad as wakeirq */
-		interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>,
+		interrupts-extended = <&gpio4 4 IRQ_TYPE_LEVEL_HIGH>,
 				      <&omap4_pmx_core 0x4e>;
 		interrupt-names = "irq", "wakeup";
 		ref-clock-frequency = <26000000>;

arch/arm/boot/dts/omap4-panda-common.dtsi

@@ -474,7 +474,7 @@ wlcore: wlcore@2 {
 		compatible = "ti,wl1271";
 		reg = <2>;
 		/* gpio_53 with gpmc_ncs3 pad as wakeup */
-		interrupts-extended = <&gpio2 21 IRQ_TYPE_EDGE_RISING>,
+		interrupts-extended = <&gpio2 21 IRQ_TYPE_LEVEL_HIGH>,
 				      <&omap4_pmx_core 0x3a>;
 		interrupt-names = "irq", "wakeup";
 		ref-clock-frequency = <38400000>;

arch/arm/boot/dts/omap4-sdp.dts

@@ -512,7 +512,7 @@ wlcore: wlcore@2 {
 		compatible = "ti,wl1281";
 		reg = <2>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <21 IRQ_TYPE_EDGE_RISING>; /* gpio 53 */
+		interrupts = <21 IRQ_TYPE_LEVEL_HIGH>; /* gpio 53 */
 		ref-clock-frequency = <26000000>;
 		tcxo-clock-frequency = <26000000>;
 	};

arch/arm/boot/dts/omap4-var-som-om44-wlan.dtsi

@@ -69,7 +69,7 @@ wlcore: wlcore@2 {
 		compatible = "ti,wl1271";
 		reg = <2>;
 		interrupt-parent = <&gpio2>;
-		interrupts = <9 IRQ_TYPE_EDGE_RISING>; /* gpio 41 */
+		interrupts = <9 IRQ_TYPE_LEVEL_HIGH>; /* gpio 41 */
 		ref-clock-frequency = <38400000>;
 	};
 };

arch/arm/boot/dts/omap5-board-common.dtsi

@@ -362,7 +362,7 @@ wlcore: wlcore@2 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&wlcore_irq_pin>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <14 IRQ_TYPE_EDGE_RISING>;	/* gpio 14 */
+		interrupts = <14 IRQ_TYPE_LEVEL_HIGH>;	/* gpio 14 */
 		ref-clock-frequency = <26000000>;
 	};
 };

arch/arm/boot/dts/omap54xx-clocks.dtsi

@@ -1146,7 +1146,7 @@ dss_clkctrl: clk@20 {
 		};
 	};
 
-	gpu_cm: clock-controller@1500 {
+	gpu_cm: gpu_cm@1500 {
 		compatible = "ti,omap4-cm";
 		reg = <0x1500 0x100>;
 		#address-cells = <1>;

arch/arm/configs/omap2plus_defconfig

@@ -356,14 +356,15 @@ CONFIG_DRM_OMAP_CONNECTOR_HDMI=m
 CONFIG_DRM_OMAP_CONNECTOR_ANALOG_TV=m
 CONFIG_DRM_OMAP_PANEL_DPI=m
 CONFIG_DRM_OMAP_PANEL_DSI_CM=m
-CONFIG_DRM_OMAP_PANEL_SONY_ACX565AKM=m
-CONFIG_DRM_OMAP_PANEL_LGPHILIPS_LB035Q02=m
-CONFIG_DRM_OMAP_PANEL_SHARP_LS037V7DW01=m
-CONFIG_DRM_OMAP_PANEL_TPO_TD028TTEC1=m
-CONFIG_DRM_OMAP_PANEL_TPO_TD043MTEA1=m
-CONFIG_DRM_OMAP_PANEL_NEC_NL8048HL11=m
 CONFIG_DRM_TILCDC=m
 CONFIG_DRM_PANEL_SIMPLE=m
+CONFIG_DRM_TI_TFP410=m
+CONFIG_DRM_PANEL_LG_LB035Q02=m
+CONFIG_DRM_PANEL_NEC_NL8048HL11=m
+CONFIG_DRM_PANEL_SHARP_LS037V7DW01=m
+CONFIG_DRM_PANEL_SONY_ACX565AKM=m
+CONFIG_DRM_PANEL_TPO_TD028TTEC1=m
+CONFIG_DRM_PANEL_TPO_TD043MTEA1=m
 CONFIG_FB=y
 CONFIG_FIRMWARE_EDID=y
 CONFIG_FB_MODE_HELPERS=y
@@ -423,6 +424,7 @@ CONFIG_USB_SERIAL_GENERIC=y
 CONFIG_USB_SERIAL_SIMPLE=m
 CONFIG_USB_SERIAL_FTDI_SIO=m
 CONFIG_USB_SERIAL_PL2303=m
+CONFIG_USB_SERIAL_OPTION=m
 CONFIG_USB_TEST=m
 CONFIG_NOP_USB_XCEIV=m
 CONFIG_AM335X_PHY_USB=m
@@ -460,6 +462,7 @@ CONFIG_MMC_SDHCI_OMAP=y
 CONFIG_NEW_LEDS=y
 CONFIG_LEDS_CLASS=m
 CONFIG_LEDS_CPCAP=m
+CONFIG_LEDS_LM3532=m
 CONFIG_LEDS_GPIO=m
 CONFIG_LEDS_PCA963X=m
 CONFIG_LEDS_PWM=m

arch/arm/mach-omap1/Kconfig

@@ -4,30 +4,25 @@ if ARCH_OMAP1
 menu "TI OMAP1 specific features"
 
 comment "OMAP Core Type"
-	depends on ARCH_OMAP1
 
 config ARCH_OMAP730
-	depends on ARCH_OMAP1
 	bool "OMAP730 Based System"
 	select ARCH_OMAP_OTG
 	select CPU_ARM926T
 	select OMAP_MPU_TIMER
 
 config ARCH_OMAP850
-	depends on ARCH_OMAP1
 	bool "OMAP850 Based System"
 	select ARCH_OMAP_OTG
 	select CPU_ARM926T
 
 config ARCH_OMAP15XX
-	depends on ARCH_OMAP1
 	default y
 	bool "OMAP15xx Based System"
 	select CPU_ARM925T
 	select OMAP_MPU_TIMER
 
 config ARCH_OMAP16XX
-	depends on ARCH_OMAP1
 	bool "OMAP16xx Based System"
 	select ARCH_OMAP_OTG
 	select CPU_ARM926T
@@ -35,7 +30,6 @@ config ARCH_OMAP16XX
 
 config OMAP_MUX
 	bool "OMAP multiplexing support"
-	depends on ARCH_OMAP
 	default y
 	help
 	  Pin multiplexing support for OMAP boards. If your bootloader
@@ -60,25 +54,24 @@ config OMAP_MUX_WARNINGS
 	  printed, it's safe to deselect OMAP_MUX for your product.
 
 comment "OMAP Board Type"
-	depends on ARCH_OMAP1
 
 config MACH_OMAP_INNOVATOR
 	bool "TI Innovator"
-	depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX)
+	depends on ARCH_OMAP15XX || ARCH_OMAP16XX
 	help
           TI OMAP 1510 or 1610 Innovator board support. Say Y here if you
           have such a board.
 
 config MACH_OMAP_H2
 	bool "TI H2 Support"
-	depends on ARCH_OMAP1 && ARCH_OMAP16XX
+	depends on ARCH_OMAP16XX
     	help
 	  TI OMAP 1610/1611B H2 board support. Say Y here if you have such
 	  a board.
 
 config MACH_OMAP_H3
 	bool "TI H3 Support"
-	depends on ARCH_OMAP1 && ARCH_OMAP16XX
+	depends on ARCH_OMAP16XX
     	help
 	  TI OMAP 1710 H3 board support. Say Y here if you have such
 	  a board.
@@ -91,7 +84,7 @@ config MACH_HERALD
 
 config MACH_OMAP_OSK
 	bool "TI OSK Support"
-	depends on ARCH_OMAP1 && ARCH_OMAP16XX
+	depends on ARCH_OMAP16XX
     	help
 	  TI OMAP 5912 OSK (OMAP Starter Kit) board support. Say Y here
           if you have such a board.
@@ -106,21 +99,21 @@ config OMAP_OSK_MISTRAL
 
 config MACH_OMAP_PERSEUS2
 	bool "TI Perseus2"
-	depends on ARCH_OMAP1 && ARCH_OMAP730
+	depends on ARCH_OMAP730
     	help
 	  Support for TI OMAP 730 Perseus2 board. Say Y here if you have such
 	  a board.
 
 config MACH_OMAP_FSAMPLE
 	bool "TI F-Sample"
-	depends on ARCH_OMAP1 && ARCH_OMAP730
+	depends on ARCH_OMAP730
     	help
 	  Support for TI OMAP 850 F-Sample board. Say Y here if you have such
 	  a board.
 
 config MACH_OMAP_PALMTE
 	bool "Palm Tungsten E"
-	depends on ARCH_OMAP1 && ARCH_OMAP15XX
+	depends on ARCH_OMAP15XX
 	help
 	  Support for the Palm Tungsten E PDA.  To boot the kernel, you'll
 	  need a PalmOS compatible bootloader; check out
@@ -129,7 +122,7 @@ config MACH_OMAP_PALMTE
 
 config MACH_OMAP_PALMZ71
 	bool "Palm Zire71"
-	depends on ARCH_OMAP1 && ARCH_OMAP15XX
+	depends on ARCH_OMAP15XX
 	help
 	 Support for the Palm Zire71 PDA. To boot the kernel,
 	 you'll need a PalmOS compatible bootloader; check out
@@ -138,7 +131,7 @@ config MACH_OMAP_PALMZ71
 
 config MACH_OMAP_PALMTT
 	bool "Palm Tungsten|T"
-	depends on ARCH_OMAP1 && ARCH_OMAP15XX
+	depends on ARCH_OMAP15XX
 	help
 	  Support for the Palm Tungsten|T PDA. To boot the kernel, you'll
 	  need a PalmOS compatible bootloader (Garux); check out
@@ -147,7 +140,7 @@ config MACH_OMAP_PALMTT
 
 config MACH_SX1
 	bool "Siemens SX1"
-	depends on ARCH_OMAP1 && ARCH_OMAP15XX
+	depends on ARCH_OMAP15XX
 	select I2C
 	help
 	  Support for the Siemens SX1 phone. To boot the kernel,
@@ -159,14 +152,14 @@ config MACH_SX1
 
 config MACH_NOKIA770
 	bool "Nokia 770"
-	depends on ARCH_OMAP1 && ARCH_OMAP16XX
+	depends on ARCH_OMAP16XX
 	help
 	  Support for the Nokia 770 Internet Tablet. Say Y here if you
 	  have such a device.
 
 config MACH_AMS_DELTA
 	bool "Amstrad E3 (Delta)"
-	depends on ARCH_OMAP1 && ARCH_OMAP15XX
+	depends on ARCH_OMAP15XX
 	select FIQ
 	select GPIO_GENERIC_PLATFORM
 	select LEDS_GPIO_REGISTER
@@ -178,7 +171,7 @@ config MACH_AMS_DELTA
 
 config MACH_OMAP_GENERIC
 	bool "Generic OMAP board"
-	depends on ARCH_OMAP1 && (ARCH_OMAP15XX || ARCH_OMAP16XX)
+	depends on ARCH_OMAP15XX || ARCH_OMAP16XX
 	help
           Support for generic OMAP-1510, 1610 or 1710 board with
           no FPGA. Can be used as template for porting Linux to

arch/arm/mach-omap1/ams-delta-fiq.c

@@ -110,7 +110,7 @@ void __init ams_delta_init_fiq(struct gpio_chip *chip,
 
 		/*
 		 * FIQ handler takes full control over serio data and clk GPIO
-		 * pins.  Initiaize them and keep requested so nobody can
+		 * pins.  Initialize them and keep requested so nobody can
 		 * interfere.  Fail if any of those two couldn't be requested.
 		 */
 		switch (i) {

arch/arm/mach-omap2/Makefile

@@ -29,6 +29,11 @@ obj-y += mcbsp.o
 endif
 
 obj-$(CONFIG_TWL4030_CORE) += omap_twl.o
+
+ifneq ($(CONFIG_MFD_CPCAP),)
+obj-y 					+= pmic-cpcap.o
+endif
+
 obj-$(CONFIG_SOC_HAS_OMAP2_SDRC)	+= sdrc.o
 
 # SMP support ONLY available for OMAP4

arch/arm/mach-omap2/clockdomain.c

@@ -1147,7 +1147,21 @@ void clkdm_del_autodeps(struct clockdomain *clkdm)
 
 /* Clockdomain-to-clock/hwmod framework interface code */
 
-static int _clkdm_clk_hwmod_enable(struct clockdomain *clkdm)
+/**
+ * clkdm_clk_enable - add an enabled downstream clock to this clkdm
+ * @clkdm: struct clockdomain *
+ * @clk: struct clk * of the enabled downstream clock
+ *
+ * Increment the usecount of the clockdomain @clkdm and ensure that it
+ * is awake before @clk is enabled.  Intended to be called by
+ * clk_enable() code.  If the clockdomain is in software-supervised
+ * idle mode, force the clockdomain to wake.  If the clockdomain is in
+ * hardware-supervised idle mode, add clkdm-pwrdm autodependencies, to
+ * ensure that devices in the clockdomain can be read from/written to
+ * by on-chip processors.  Returns -EINVAL if passed null pointers;
+ * returns 0 upon success or if the clockdomain is in hwsup idle mode.
+ */
+int clkdm_clk_enable(struct clockdomain *clkdm, struct clk *unused)
 {
 	if (!clkdm || !arch_clkdm || !arch_clkdm->clkdm_clk_enable)
 		return -EINVAL;
@@ -1174,33 +1188,6 @@ static int _clkdm_clk_hwmod_enable(struct clockdomain *clkdm)
 	return 0;
 }
 
-/**
- * clkdm_clk_enable - add an enabled downstream clock to this clkdm
- * @clkdm: struct clockdomain *
- * @clk: struct clk * of the enabled downstream clock
- *
- * Increment the usecount of the clockdomain @clkdm and ensure that it
- * is awake before @clk is enabled.  Intended to be called by
- * clk_enable() code.  If the clockdomain is in software-supervised
- * idle mode, force the clockdomain to wake.  If the clockdomain is in
- * hardware-supervised idle mode, add clkdm-pwrdm autodependencies, to
- * ensure that devices in the clockdomain can be read from/written to
- * by on-chip processors.  Returns -EINVAL if passed null pointers;
- * returns 0 upon success or if the clockdomain is in hwsup idle mode.
- */
-int clkdm_clk_enable(struct clockdomain *clkdm, struct clk *clk)
-{
-	/*
-	 * XXX Rewrite this code to maintain a list of enabled
-	 * downstream clocks for debugging purposes?
-	 */
-
-	if (!clk)
-		return -EINVAL;
-
-	return _clkdm_clk_hwmod_enable(clkdm);
-}
-
 /**
  * clkdm_clk_disable - remove an enabled downstream clock from this clkdm
  * @clkdm: struct clockdomain *
@@ -1216,13 +1203,13 @@ int clkdm_clk_enable(struct clockdomain *clkdm, struct clk *clk)
  */
 int clkdm_clk_disable(struct clockdomain *clkdm, struct clk *clk)
 {
-	if (!clkdm || !clk || !arch_clkdm || !arch_clkdm->clkdm_clk_disable)
+	if (!clkdm || !arch_clkdm || !arch_clkdm->clkdm_clk_disable)
 		return -EINVAL;
 
 	pwrdm_lock(clkdm->pwrdm.ptr);
 
 	/* corner case: disabling unused clocks */
-	if ((__clk_get_enable_count(clk) == 0) && clkdm->usecount == 0)
+	if (clk && (__clk_get_enable_count(clk) == 0) && clkdm->usecount == 0)
 		goto ccd_exit;
 
 	if (clkdm->usecount == 0) {
@@ -1277,7 +1264,7 @@ int clkdm_hwmod_enable(struct clockdomain *clkdm, struct omap_hwmod *oh)
 	if (!oh)
 		return -EINVAL;
 
-	return _clkdm_clk_hwmod_enable(clkdm);
+	return clkdm_clk_enable(clkdm, NULL);
 }
 
 /**
@@ -1300,35 +1287,10 @@ int clkdm_hwmod_disable(struct clockdomain *clkdm, struct omap_hwmod *oh)
 	if (cpu_is_omap24xx() || cpu_is_omap34xx())
 		return 0;
 
-	/*
-	 * XXX Rewrite this code to maintain a list of enabled
-	 * downstream hwmods for debugging purposes?
-	 */
-
-	if (!clkdm || !oh || !arch_clkdm || !arch_clkdm->clkdm_clk_disable)
+	if (!oh)
 		return -EINVAL;
 
-	pwrdm_lock(clkdm->pwrdm.ptr);
-
-	if (clkdm->usecount == 0) {
-		pwrdm_unlock(clkdm->pwrdm.ptr);
-		WARN_ON(1); /* underflow */
-		return -ERANGE;
-	}
-
-	clkdm->usecount--;
-	if (clkdm->usecount > 0) {
-		pwrdm_unlock(clkdm->pwrdm.ptr);
-		return 0;
-	}
-
-	arch_clkdm->clkdm_clk_disable(clkdm);
-	pwrdm_state_switch_nolock(clkdm->pwrdm.ptr);
-	pwrdm_unlock(clkdm->pwrdm.ptr);
-
-	pr_debug("clockdomain: %s: disabled\n", clkdm->name);
-
-	return 0;
+	return clkdm_clk_disable(clkdm, NULL);
 }
 
 /**

arch/arm/mach-omap2/control.c

@@ -684,7 +684,7 @@ static u32 am33xx_control_vals[ARRAY_SIZE(am43xx_control_reg_offsets)];
  *
  * Save the wkup domain registers
  */
-void am43xx_control_save_context(void)
+static void am43xx_control_save_context(void)
 {
 	int i;
 
@@ -698,7 +698,7 @@ void am43xx_control_save_context(void)
  *
  * Restore the wkup domain registers
  */
-void am43xx_control_restore_context(void)
+static void am43xx_control_restore_context(void)
 {
 	int i;
 

arch/arm/mach-omap2/control.h

@@ -195,6 +195,7 @@
 #define OMAP44XX_CONTROL_FUSE_MPU_OPP100	0x243
 #define OMAP44XX_CONTROL_FUSE_MPU_OPPTURBO	0x246
 #define OMAP44XX_CONTROL_FUSE_MPU_OPPNITRO	0x249
+#define OMAP44XX_CONTROL_FUSE_MPU_OPPNITROSB	0x24C
 #define OMAP44XX_CONTROL_FUSE_CORE_OPP50	0x254
 #define OMAP44XX_CONTROL_FUSE_CORE_OPP100	0x257
 #define OMAP44XX_CONTROL_FUSE_CORE_OPP100OV	0x25A

arch/arm/mach-omap2/display.c

@@ -265,6 +265,7 @@ static int __init omapdss_init_of(void)
 	r = of_platform_populate(node, NULL, NULL, &pdev->dev);
 	if (r) {
 		pr_err("Unable to populate DSS submodule devices\n");
+		put_device(&pdev->dev);
 		return r;
 	}
 

arch/arm/mach-omap2/omap-mpuss-lowpower.c

@@ -227,7 +227,6 @@ int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state)
 {
 	struct omap4_cpu_pm_info *pm_info = &per_cpu(omap4_pm_info, cpu);
 	unsigned int save_state = 0, cpu_logic_state = PWRDM_POWER_RET;
-	unsigned int wakeup_cpu;
 
 	if (omap_rev() == OMAP4430_REV_ES1_0)
 		return -ENXIO;
@@ -292,7 +291,6 @@ int omap4_enter_lowpower(unsigned int cpu, unsigned int power_state)
 	 * secure devices, CPUx does WFI which can result in
 	 * domain transition
 	 */
-	wakeup_cpu = smp_processor_id();
 	pwrdm_set_next_pwrst(pm_info->pwrdm, PWRDM_POWER_ON);
 
 	pwrdm_post_transition(NULL);

arch/arm/mach-omap2/omap_device.c

@@ -119,11 +119,7 @@ static void _add_hwmod_clocks_clkdev(struct omap_device *od,
 
 /**
  * omap_device_build_from_dt - build an omap_device with multiple hwmods
- * @pdev_name: name of the platform_device driver to use
- * @pdev_id: this platform_device's connection ID
- * @oh: ptr to the single omap_hwmod that backs this omap_device
- * @pdata: platform_data ptr to associate with the platform_device
- * @pdata_len: amount of memory pointed to by @pdata
+ * @pdev: The platform device to update.
  *
  * Function for building an omap_device already registered from device-tree
  *
@@ -292,7 +288,7 @@ static int _omap_device_idle_hwmods(struct omap_device *od)
 
 /**
  * omap_device_get_context_loss_count - get lost context count
- * @od: struct omap_device *
+ * @pdev: The platform device to update.
  *
  * Using the primary hwmod, query the context loss count for this
  * device.
@@ -321,9 +317,8 @@ int omap_device_get_context_loss_count(struct platform_device *pdev)
 /**
  * omap_device_alloc - allocate an omap_device
  * @pdev: platform_device that will be included in this omap_device
- * @oh: ptr to the single omap_hwmod that backs this omap_device
- * @pdata: platform_data ptr to associate with the platform_device
- * @pdata_len: amount of memory pointed to by @pdata
+ * @ohs: ptr to the omap_hwmod for this omap_device
+ * @oh_cnt: the size of the ohs list
  *
  * Convenience function for allocating an omap_device structure and filling
  * hwmods, and resources.
@@ -649,7 +644,7 @@ struct dev_pm_domain omap_device_pm_domain = {
 
 /**
  * omap_device_register - register an omap_device with one omap_hwmod
- * @od: struct omap_device * to register
+ * @pdev: the platform device (omap_device) to register.
  *
  * Register the omap_device structure.  This currently just calls
  * platform_device_register() on the underlying platform_device.
@@ -668,7 +663,7 @@ int omap_device_register(struct platform_device *pdev)
 
 /**
  * omap_device_enable - fully activate an omap_device
- * @od: struct omap_device * to activate
+ * @pdev: the platform device to activate
  *
  * Do whatever is necessary for the hwmods underlying omap_device @od
  * to be accessible and ready to operate.  This generally involves
@@ -702,7 +697,7 @@ int omap_device_enable(struct platform_device *pdev)
 
 /**
  * omap_device_idle - idle an omap_device
- * @od: struct omap_device * to idle
+ * @pdev: The platform_device (omap_device) to idle
  *
  * Idle omap_device @od.  Device drivers call this function indirectly
  * via pm_runtime_put*().  Returns -EINVAL if the omap_device is not

arch/arm/mach-omap2/omap_hwmod.c

@@ -623,39 +623,6 @@ static int _enable_wakeup(struct omap_hwmod *oh, u32 *v)
 	return 0;
 }
 
-/**
- * _disable_wakeup: clear OCP_SYSCONFIG.ENAWAKEUP bit in the hardware
- * @oh: struct omap_hwmod *
- *
- * Prevent the hardware module @oh to send wakeups.  Returns -EINVAL
- * upon error or 0 upon success.
- */
-static int _disable_wakeup(struct omap_hwmod *oh, u32 *v)
-{
-	if (!oh->class->sysc ||
-	    !((oh->class->sysc->sysc_flags & SYSC_HAS_ENAWAKEUP) ||
-	      (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP) ||
-	      (oh->class->sysc->idlemodes & MSTANDBY_SMART_WKUP)))
-		return -EINVAL;
-
-	if (!oh->class->sysc->sysc_fields) {
-		WARN(1, "omap_hwmod: %s: offset struct for sysconfig not provided in class\n", oh->name);
-		return -EINVAL;
-	}
-
-	if (oh->class->sysc->sysc_flags & SYSC_HAS_ENAWAKEUP)
-		*v &= ~(0x1 << oh->class->sysc->sysc_fields->enwkup_shift);
-
-	if (oh->class->sysc->idlemodes & SIDLE_SMART_WKUP)
-		_set_slave_idlemode(oh, HWMOD_IDLEMODE_SMART, v);
-	if (oh->class->sysc->idlemodes & MSTANDBY_SMART_WKUP)
-		_set_master_standbymode(oh, HWMOD_IDLEMODE_SMART, v);
-
-	/* XXX test pwrdm_get_wken for this hwmod's subsystem */
-
-	return 0;
-}
-
 static struct clockdomain *_get_clkdm(struct omap_hwmod *oh)
 {
 	struct clk_hw_omap *clk;
@@ -3867,70 +3834,6 @@ void __iomem *omap_hwmod_get_mpu_rt_va(struct omap_hwmod *oh)
  * for context save/restore operations?
  */
 
-/**
- * omap_hwmod_enable_wakeup - allow device to wake up the system
- * @oh: struct omap_hwmod *
- *
- * Sets the module OCP socket ENAWAKEUP bit to allow the module to
- * send wakeups to the PRCM, and enable I/O ring wakeup events for
- * this IP block if it has dynamic mux entries.  Eventually this
- * should set PRCM wakeup registers to cause the PRCM to receive
- * wakeup events from the module.  Does not set any wakeup routing
- * registers beyond this point - if the module is to wake up any other
- * module or subsystem, that must be set separately.  Called by
- * omap_device code.  Returns -EINVAL on error or 0 upon success.
- */
-int omap_hwmod_enable_wakeup(struct omap_hwmod *oh)
-{
-	unsigned long flags;
-	u32 v;
-
-	spin_lock_irqsave(&oh->_lock, flags);
-
-	if (oh->class->sysc &&
-	    (oh->class->sysc->sysc_flags & SYSC_HAS_ENAWAKEUP)) {
-		v = oh->_sysc_cache;
-		_enable_wakeup(oh, &v);
-		_write_sysconfig(v, oh);
-	}
-
-	spin_unlock_irqrestore(&oh->_lock, flags);
-
-	return 0;
-}
-
-/**
- * omap_hwmod_disable_wakeup - prevent device from waking the system
- * @oh: struct omap_hwmod *
- *
- * Clears the module OCP socket ENAWAKEUP bit to prevent the module
- * from sending wakeups to the PRCM, and disable I/O ring wakeup
- * events for this IP block if it has dynamic mux entries.  Eventually
- * this should clear PRCM wakeup registers to cause the PRCM to ignore
- * wakeup events from the module.  Does not set any wakeup routing
- * registers beyond this point - if the module is to wake up any other
- * module or subsystem, that must be set separately.  Called by
- * omap_device code.  Returns -EINVAL on error or 0 upon success.
- */
-int omap_hwmod_disable_wakeup(struct omap_hwmod *oh)
-{
-	unsigned long flags;
-	u32 v;
-
-	spin_lock_irqsave(&oh->_lock, flags);
-
-	if (oh->class->sysc &&
-	    (oh->class->sysc->sysc_flags & SYSC_HAS_ENAWAKEUP)) {
-		v = oh->_sysc_cache;
-		_disable_wakeup(oh, &v);
-		_write_sysconfig(v, oh);
-	}
-
-	spin_unlock_irqrestore(&oh->_lock, flags);
-
-	return 0;
-}
-
 /**
  * omap_hwmod_assert_hardreset - assert the HW reset line of submodules
  * contained in the hwmod module.

arch/arm/mach-omap2/omap_hwmod.h

@@ -646,9 +646,6 @@ int omap_hwmod_get_resource_byname(struct omap_hwmod *oh, unsigned int type,
 struct powerdomain *omap_hwmod_get_pwrdm(struct omap_hwmod *oh);
 void __iomem *omap_hwmod_get_mpu_rt_va(struct omap_hwmod *oh);
 
-int omap_hwmod_enable_wakeup(struct omap_hwmod *oh);
-int omap_hwmod_disable_wakeup(struct omap_hwmod *oh);
-
 int omap_hwmod_for_each_by_class(const char *classname,
 				 int (*fn)(struct omap_hwmod *oh,
 					   void *user),

arch/arm/mach-omap2/omap_hwmod_33xx_43xx_ipblock_data.c

@@ -583,7 +583,8 @@ static struct omap_hwmod_class_sysconfig am33xx_timer_sysc = {
 	.rev_offs	= 0x0000,
 	.sysc_offs	= 0x0010,
 	.syss_offs	= 0x0014,
-	.sysc_flags	= (SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET),
+	.sysc_flags	= SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET |
+			  SYSC_HAS_RESET_STATUS,
 	.idlemodes	= (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
 			  SIDLE_SMART_WKUP),
 	.sysc_fields	= &omap_hwmod_sysc_type2,

arch/arm/mach-omap2/omap_hwmod_33xx_data.c

@@ -230,8 +230,9 @@ static struct omap_hwmod am33xx_control_hwmod = {
 static struct omap_hwmod_class_sysconfig lcdc_sysc = {
 	.rev_offs	= 0x0,
 	.sysc_offs	= 0x54,
-	.sysc_flags	= (SYSC_HAS_SIDLEMODE | SYSC_HAS_MIDLEMODE),
-	.idlemodes	= (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART),
+	.sysc_flags	= SYSC_HAS_SIDLEMODE | SYSC_HAS_MIDLEMODE,
+	.idlemodes	= SIDLE_FORCE | SIDLE_NO | SIDLE_SMART |
+			  MSTANDBY_FORCE | MSTANDBY_NO | MSTANDBY_SMART,
 	.sysc_fields	= &omap_hwmod_sysc_type2,
 };
 

arch/arm/mach-omap2/omap_hwmod_44xx_data.c

@@ -790,7 +790,7 @@ static struct omap_hwmod_class omap44xx_sha0_hwmod_class = {
 	.sysc		= &omap44xx_sha0_sysc,
 };
 
-struct omap_hwmod omap44xx_sha0_hwmod = {
+static struct omap_hwmod omap44xx_sha0_hwmod = {
 	.name		= "sham",
 	.class		= &omap44xx_sha0_hwmod_class,
 	.clkdm_name	= "l4_secure_clkdm",
@@ -974,7 +974,7 @@ static struct omap_hwmod omap44xx_des_hwmod = {
 	},
 };
 
-struct omap_hwmod_ocp_if omap44xx_l3_main_2__des = {
+static struct omap_hwmod_ocp_if omap44xx_l3_main_2__des = {
 	.master		= &omap44xx_l3_main_2_hwmod,
 	.slave		= &omap44xx_des_hwmod,
 	.clk		= "l3_div_ck",

arch/arm/mach-omap2/omap_hwmod_7xx_data.c

@@ -682,7 +682,7 @@ static struct omap_hwmod_class dra7xx_sha0_hwmod_class = {
 	.sysc		= &dra7xx_sha0_sysc,
 };
 
-struct omap_hwmod dra7xx_sha0_hwmod = {
+static struct omap_hwmod dra7xx_sha0_hwmod = {
 	.name		= "sham",
 	.class		= &dra7xx_sha0_hwmod_class,
 	.clkdm_name	= "l4sec_clkdm",

arch/arm/mach-omap2/omap_twl.c

@@ -36,11 +36,6 @@
 #define OMAP4_VDD_CORE_SR_VOLT_REG	0x61
 #define OMAP4_VDD_CORE_SR_CMD_REG	0x62
 
-#define OMAP4_VP_CONFIG_ERROROFFSET	0x00
-#define OMAP4_VP_VSTEPMIN_VSTEPMIN	0x01
-#define OMAP4_VP_VSTEPMAX_VSTEPMAX	0x04
-#define OMAP4_VP_VLIMITTO_TIMEOUT_US	200
-
 static bool is_offset_valid;
 static u8 smps_offset;
 
@@ -219,7 +214,8 @@ int __init omap4_twl_init(void)
 {
 	struct voltagedomain *voltdm;
 
-	if (!cpu_is_omap44xx())
+	if (!cpu_is_omap44xx() ||
+	    of_find_compatible_node(NULL, NULL, "motorola,cpcap"))
 		return -ENODEV;
 
 	voltdm = voltdm_lookup("mpu");

arch/arm/mach-omap2/opp4xxx_data.c

@@ -32,20 +32,22 @@
 
 #define OMAP4430_VDD_MPU_OPP50_UV		1025000
 #define OMAP4430_VDD_MPU_OPP100_UV		1200000
-#define OMAP4430_VDD_MPU_OPPTURBO_UV		1313000
-#define OMAP4430_VDD_MPU_OPPNITRO_UV		1375000
+#define OMAP4430_VDD_MPU_OPPTURBO_UV		1325000
+#define OMAP4430_VDD_MPU_OPPNITRO_UV		1388000
+#define OMAP4430_VDD_MPU_OPPNITROSB_UV		1398000
 
 struct omap_volt_data omap443x_vdd_mpu_volt_data[] = {
 	VOLT_DATA_DEFINE(OMAP4430_VDD_MPU_OPP50_UV, OMAP44XX_CONTROL_FUSE_MPU_OPP50, 0xf4, 0x0c),
 	VOLT_DATA_DEFINE(OMAP4430_VDD_MPU_OPP100_UV, OMAP44XX_CONTROL_FUSE_MPU_OPP100, 0xf9, 0x16),
 	VOLT_DATA_DEFINE(OMAP4430_VDD_MPU_OPPTURBO_UV, OMAP44XX_CONTROL_FUSE_MPU_OPPTURBO, 0xfa, 0x23),
 	VOLT_DATA_DEFINE(OMAP4430_VDD_MPU_OPPNITRO_UV, OMAP44XX_CONTROL_FUSE_MPU_OPPNITRO, 0xfa, 0x27),
+	VOLT_DATA_DEFINE(OMAP4430_VDD_MPU_OPPNITROSB_UV, OMAP44XX_CONTROL_FUSE_MPU_OPPNITROSB, 0xfa, 0x27),
 	VOLT_DATA_DEFINE(0, 0, 0, 0),
 };
 
-#define OMAP4430_VDD_IVA_OPP50_UV		1013000
-#define OMAP4430_VDD_IVA_OPP100_UV		1188000
-#define OMAP4430_VDD_IVA_OPPTURBO_UV		1300000
+#define OMAP4430_VDD_IVA_OPP50_UV		 950000
+#define OMAP4430_VDD_IVA_OPP100_UV		1114000
+#define OMAP4430_VDD_IVA_OPPTURBO_UV		1291000
 
 struct omap_volt_data omap443x_vdd_iva_volt_data[] = {
 	VOLT_DATA_DEFINE(OMAP4430_VDD_IVA_OPP50_UV, OMAP44XX_CONTROL_FUSE_IVA_OPP50, 0xf4, 0x0c),
@@ -54,8 +56,8 @@ struct omap_volt_data omap443x_vdd_iva_volt_data[] = {
 	VOLT_DATA_DEFINE(0, 0, 0, 0),
 };
 
-#define OMAP4430_VDD_CORE_OPP50_UV		1025000
-#define OMAP4430_VDD_CORE_OPP100_UV		1200000
+#define OMAP4430_VDD_CORE_OPP50_UV		 962000
+#define OMAP4430_VDD_CORE_OPP100_UV		1127000
 
 struct omap_volt_data omap443x_vdd_core_volt_data[] = {
 	VOLT_DATA_DEFINE(OMAP4430_VDD_CORE_OPP50_UV, OMAP44XX_CONTROL_FUSE_CORE_OPP50, 0xf4, 0x0c),

arch/arm/mach-omap2/pdata-quirks.c

@@ -11,7 +11,6 @@
 #include <linux/init.h>
 #include <linux/kernel.h>
 #include <linux/of_platform.h>
-#include <linux/ti_wilink_st.h>
 #include <linux/wl12xx.h>
 #include <linux/mmc/card.h>
 #include <linux/mmc/host.h>
@@ -139,53 +138,6 @@ static void __init omap3_sbc_t3530_legacy_init(void)
 	omap3_sbc_t3x_usb_hub_init(167, "sb-t35 usb hub");
 }
 
-static struct ti_st_plat_data wilink_pdata = {
-	.nshutdown_gpio = 137,
-	.dev_name = "/dev/ttyO1",
-	.flow_cntrl = 1,
-	.baud_rate = 300000,
-};
-
-static struct platform_device wl18xx_device = {
-	.name	= "kim",
-	.id	= -1,
-	.dev	= {
-		.platform_data = &wilink_pdata,
-	}
-};
-
-static struct ti_st_plat_data wilink7_pdata = {
-	.nshutdown_gpio = 162,
-	.dev_name = "/dev/ttyO1",
-	.flow_cntrl = 1,
-	.baud_rate = 3000000,
-};
-
-static struct platform_device wl128x_device = {
-	.name	= "kim",
-	.id	= -1,
-	.dev	= {
-		.platform_data = &wilink7_pdata,
-	}
-};
-
-static struct platform_device btwilink_device = {
-	.name	= "btwilink",
-	.id	= -1,
-};
-
-static void __init omap3_igep0020_rev_f_legacy_init(void)
-{
-	platform_device_register(&wl18xx_device);
-	platform_device_register(&btwilink_device);
-}
-
-static void __init omap3_igep0030_rev_g_legacy_init(void)
-{
-	platform_device_register(&wl18xx_device);
-	platform_device_register(&btwilink_device);
-}
-
 static void __init omap3_evm_legacy_init(void)
 {
 	hsmmc2_internal_input_clk();
@@ -299,8 +251,6 @@ static void __init omap3_tao3530_legacy_init(void)
 static void __init omap3_logicpd_torpedo_init(void)
 {
 	omap3_gpio126_127_129();
-	platform_device_register(&wl128x_device);
-	platform_device_register(&btwilink_device);
 }
 
 /* omap3pandora legacy devices */
@@ -679,8 +629,6 @@ static struct pdata_init pdata_quirks[] __initdata = {
 	{ "nokia,omap3-n900", nokia_n900_legacy_init, },
 	{ "nokia,omap3-n9", hsmmc2_internal_input_clk, },
 	{ "nokia,omap3-n950", hsmmc2_internal_input_clk, },
-	{ "isee,omap3-igep0020-rev-f", omap3_igep0020_rev_f_legacy_init, },
-	{ "isee,omap3-igep0030-rev-g", omap3_igep0030_rev_g_legacy_init, },
 	{ "logicpd,dm3730-torpedo-devkit", omap3_logicpd_torpedo_init, },
 	{ "ti,omap3-evm-37xx", omap3_evm_legacy_init, },
 	{ "ti,am3517-evm", am3517_evm_legacy_init, },

arch/arm/mach-omap2/pm.c

@@ -74,83 +74,6 @@ int omap_pm_clkdms_setup(struct clockdomain *clkdm, void *unused)
 	return 0;
 }
 
-/*
- * This API is to be called during init to set the various voltage
- * domains to the voltage as per the opp table. Typically we boot up
- * at the nominal voltage. So this function finds out the rate of
- * the clock associated with the voltage domain, finds out the correct
- * opp entry and sets the voltage domain to the voltage specified
- * in the opp entry
- */
-static int __init omap2_set_init_voltage(char *vdd_name, char *clk_name,
-					 const char *oh_name)
-{
-	struct voltagedomain *voltdm;
-	struct clk *clk;
-	struct dev_pm_opp *opp;
-	unsigned long freq, bootup_volt;
-	struct device *dev;
-
-	if (!vdd_name || !clk_name || !oh_name) {
-		pr_err("%s: invalid parameters\n", __func__);
-		goto exit;
-	}
-
-	if (!strncmp(oh_name, "mpu", 3))
-		/* 
-		 * All current OMAPs share voltage rail and clock
-		 * source, so CPU0 is used to represent the MPU-SS.
-		 */
-		dev = get_cpu_device(0);
-	else
-		dev = omap_device_get_by_hwmod_name(oh_name);
-
-	if (IS_ERR(dev)) {
-		pr_err("%s: Unable to get dev pointer for hwmod %s\n",
-			__func__, oh_name);
-		goto exit;
-	}
-
-	voltdm = voltdm_lookup(vdd_name);
-	if (!voltdm) {
-		pr_err("%s: unable to get vdd pointer for vdd_%s\n",
-			__func__, vdd_name);
-		goto exit;
-	}
-
-	clk =  clk_get(NULL, clk_name);
-	if (IS_ERR(clk)) {
-		pr_err("%s: unable to get clk %s\n", __func__, clk_name);
-		goto exit;
-	}
-
-	freq = clk_get_rate(clk);
-	clk_put(clk);
-
-	opp = dev_pm_opp_find_freq_ceil(dev, &freq);
-	if (IS_ERR(opp)) {
-		pr_err("%s: unable to find boot up OPP for vdd_%s\n",
-			__func__, vdd_name);
-		goto exit;
-	}
-
-	bootup_volt = dev_pm_opp_get_voltage(opp);
-	dev_pm_opp_put(opp);
-
-	if (!bootup_volt) {
-		pr_err("%s: unable to find voltage corresponding to the bootup OPP for vdd_%s\n",
-		       __func__, vdd_name);
-		goto exit;
-	}
-
-	voltdm_scale(voltdm, bootup_volt);
-	return 0;
-
-exit:
-	pr_err("%s: unable to set vdd_%s\n", __func__, vdd_name);
-	return -EINVAL;
-}
-
 #ifdef CONFIG_SUSPEND
 static int omap_pm_enter(suspend_state_t suspend_state)
 {
@@ -208,25 +131,6 @@ void omap_common_suspend_init(void *pm_suspend)
 }
 #endif /* CONFIG_SUSPEND */
 
-static void __init omap3_init_voltages(void)
-{
-	if (!soc_is_omap34xx())
-		return;
-
-	omap2_set_init_voltage("mpu_iva", "dpll1_ck", "mpu");
-	omap2_set_init_voltage("core", "l3_ick", "l3_main");
-}
-
-static void __init omap4_init_voltages(void)
-{
-	if (!soc_is_omap44xx())
-		return;
-
-	omap2_set_init_voltage("mpu", "dpll_mpu_ck", "mpu");
-	omap2_set_init_voltage("core", "l3_div_ck", "l3_main_1");
-	omap2_set_init_voltage("iva", "dpll_iva_m5x2_ck", "iva");
-}
-
 int __maybe_unused omap_pm_nop_init(void)
 {
 	return 0;
@@ -244,12 +148,9 @@ int __init omap2_common_pm_late_init(void)
 	/* Init the voltage layer */
 	omap3_twl_init();
 	omap4_twl_init();
+	omap4_cpcap_init();
 	omap_voltage_late_init();
 
-	/* Initialize the voltages */
-	omap3_init_voltages();
-	omap4_init_voltages();
-
 	/* Smartreflex device init */
 	omap_devinit_smartreflex();
 

arch/arm/mach-omap2/pm.h

@@ -107,6 +107,11 @@ extern u16 pm44xx_errata;
 #define IS_PM44XX_ERRATUM(id)		0
 #endif
 
+#define OMAP4_VP_CONFIG_ERROROFFSET	0x00
+#define OMAP4_VP_VSTEPMIN_VSTEPMIN	0x01
+#define OMAP4_VP_VSTEPMAX_VSTEPMAX	0x04
+#define OMAP4_VP_VLIMITTO_TIMEOUT_US	200
+
 #ifdef CONFIG_POWER_AVS_OMAP
 extern int omap_devinit_smartreflex(void);
 extern void omap_enable_smartreflex_on_init(void);
@@ -134,6 +139,15 @@ static inline int omap4_twl_init(void)
 }
 #endif
 
+#if IS_ENABLED(CONFIG_MFD_CPCAP)
+extern int omap4_cpcap_init(void);
+#else
+static inline int omap4_cpcap_init(void)
+{
+	return -EINVAL;
+}
+#endif
+
 #ifdef CONFIG_PM
 extern void omap_pm_setup_oscillator(u32 tstart, u32 tshut);
 extern void omap_pm_get_oscillator(u32 *tstart, u32 *tshut);

arch/arm/mach-omap2/pm44xx.c

@@ -128,18 +128,9 @@ static int __init pwrdms_setup(struct powerdomain *pwrdm, void *unused)
 		return 0;
 	}
 
-	/*
-	 * Bootloader or kexec boot may have LOGICRETSTATE cleared
-	 * for some domains. This is the case when kexec booting from
-	 * Android kernels that support off mode for example.
-	 * Make sure it's set at least for core and per, otherwise
-	 * we currently will see lost GPIO interrupts for wlcore and
-	 * smsc911x at least if per hits retention during idle.
-	 */
 	if (!strncmp(pwrdm->name, "core", 4) ||
-	    !strncmp(pwrdm->name, "l4per", 5) ||
-	    !strncmp(pwrdm->name, "wkup", 4))
-		pwrdm_set_logic_retst(pwrdm, PWRDM_POWER_RET);
+	    !strncmp(pwrdm->name, "l4per", 5))
+		pwrdm_set_logic_retst(pwrdm, PWRDM_POWER_OFF);
 
 	pwrst = kmalloc(sizeof(struct power_state), GFP_ATOMIC);
 	if (!pwrst)

arch/arm/mach-omap2/pmic-cpcap.c

+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * pmic-cpcap.c - CPCAP-specific functions for the OPP code
+ *
+ * Adapted from Motorola Mapphone Android Linux kernel
+ * Copyright (C) 2011 Motorola, Inc.
+ */
+
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+
+#include "soc.h"
+#include "pm.h"
+#include "voltage.h"
+
+#include <linux/init.h>
+#include "vc.h"
+
+/**
+ * omap_cpcap_vsel_to_vdc - convert CPCAP VSEL value to microvolts DC
+ * @vsel: CPCAP VSEL value to convert
+ *
+ * Returns the microvolts DC that the CPCAP PMIC should generate when
+ * programmed with @vsel.
+ */
+static unsigned long omap_cpcap_vsel_to_uv(unsigned char vsel)
+{
+	if (vsel > 0x44)
+		vsel = 0x44;
+	return (((vsel * 125) + 6000)) * 100;
+}
+
+/**
+ * omap_cpcap_uv_to_vsel - convert microvolts DC to CPCAP VSEL value
+ * @uv: microvolts DC to convert
+ *
+ * Returns the VSEL value necessary for the CPCAP PMIC to
+ * generate an output voltage equal to or greater than @uv microvolts DC.
+ */
+static unsigned char omap_cpcap_uv_to_vsel(unsigned long uv)
+{
+	if (uv < 600000)
+		uv = 600000;
+	else if (uv > 1450000)
+		uv = 1450000;
+	return DIV_ROUND_UP(uv - 600000, 12500);
+}
+
+static struct omap_voltdm_pmic omap_cpcap_core = {
+	.slew_rate = 4000,
+	.step_size = 12500,
+	.vp_erroroffset = OMAP4_VP_CONFIG_ERROROFFSET,
+	.vp_vstepmin = OMAP4_VP_VSTEPMIN_VSTEPMIN,
+	.vp_vstepmax = OMAP4_VP_VSTEPMAX_VSTEPMAX,
+	.vddmin = 900000,
+	.vddmax = 1350000,
+	.vp_timeout_us = OMAP4_VP_VLIMITTO_TIMEOUT_US,
+	.i2c_slave_addr = 0x02,
+	.volt_reg_addr = 0x00,
+	.cmd_reg_addr = 0x01,
+	.i2c_high_speed = false,
+	.vsel_to_uv = omap_cpcap_vsel_to_uv,
+	.uv_to_vsel = omap_cpcap_uv_to_vsel,
+};
+
+static struct omap_voltdm_pmic omap_cpcap_iva = {
+	.slew_rate = 4000,
+	.step_size = 12500,
+	.vp_erroroffset = OMAP4_VP_CONFIG_ERROROFFSET,
+	.vp_vstepmin = OMAP4_VP_VSTEPMIN_VSTEPMIN,
+	.vp_vstepmax = OMAP4_VP_VSTEPMAX_VSTEPMAX,
+	.vddmin = 900000,
+	.vddmax = 1350000,
+	.vp_timeout_us = OMAP4_VP_VLIMITTO_TIMEOUT_US,
+	.i2c_slave_addr = 0x44,
+	.volt_reg_addr = 0x0,
+	.cmd_reg_addr = 0x01,
+	.i2c_high_speed = false,
+	.vsel_to_uv = omap_cpcap_vsel_to_uv,
+	.uv_to_vsel = omap_cpcap_uv_to_vsel,
+};
+
+/**
+ * omap_max8952_vsel_to_vdc - convert MAX8952 VSEL value to microvolts DC
+ * @vsel: MAX8952 VSEL value to convert
+ *
+ * Returns the microvolts DC that the MAX8952 Regulator should generate when
+ * programmed with @vsel.
+ */
+static unsigned long omap_max8952_vsel_to_uv(unsigned char vsel)
+{
+	if (vsel > 0x3F)
+		vsel = 0x3F;
+	return (((vsel * 100) + 7700)) * 100;
+}
+
+/**
+ * omap_max8952_uv_to_vsel - convert microvolts DC to MAX8952 VSEL value
+ * @uv: microvolts DC to convert
+ *
+ * Returns the VSEL value necessary for the MAX8952 Regulator to
+ * generate an output voltage equal to or greater than @uv microvolts DC.
+ */
+static unsigned char omap_max8952_uv_to_vsel(unsigned long uv)
+{
+	if (uv < 770000)
+		uv = 770000;
+	else if (uv > 1400000)
+		uv = 1400000;
+	return DIV_ROUND_UP(uv - 770000, 10000);
+}
+
+static struct omap_voltdm_pmic omap443x_max8952_mpu = {
+	.slew_rate = 16000,
+	.step_size = 10000,
+	.vp_erroroffset = OMAP4_VP_CONFIG_ERROROFFSET,
+	.vp_vstepmin = OMAP4_VP_VSTEPMIN_VSTEPMIN,
+	.vp_vstepmax = OMAP4_VP_VSTEPMAX_VSTEPMAX,
+	.vddmin = 900000,
+	.vddmax = 1400000,
+	.vp_timeout_us = OMAP4_VP_VLIMITTO_TIMEOUT_US,
+	.i2c_slave_addr = 0x60,
+	.volt_reg_addr = 0x03,
+	.cmd_reg_addr = 0x03,
+	.i2c_high_speed = false,
+	.vsel_to_uv = omap_max8952_vsel_to_uv,
+	.uv_to_vsel = omap_max8952_uv_to_vsel,
+};
+
+/**
+ * omap_fan5355_vsel_to_vdc - convert FAN535503 VSEL value to microvolts DC
+ * @vsel: FAN535503 VSEL value to convert
+ *
+ * Returns the microvolts DC that the FAN535503 Regulator should generate when
+ * programmed with @vsel.
+ */
+static unsigned long omap_fan535503_vsel_to_uv(unsigned char vsel)
+{
+	/* Extract bits[5:0] */
+	vsel &= 0x3F;
+
+	return (((vsel * 125) + 7500)) * 100;
+}
+
+/**
+ * omap_fan535508_vsel_to_vdc - convert FAN535508 VSEL value to microvolts DC
+ * @vsel: FAN535508 VSEL value to convert
+ *
+ * Returns the microvolts DC that the FAN535508 Regulator should generate when
+ * programmed with @vsel.
+ */
+static unsigned long omap_fan535508_vsel_to_uv(unsigned char vsel)
+{
+	/* Extract bits[5:0] */
+	vsel &= 0x3F;
+
+	if (vsel > 0x37)
+		vsel = 0x37;
+	return (((vsel * 125) + 7500)) * 100;
+}
+
+
+/**
+ * omap_fan535503_uv_to_vsel - convert microvolts DC to FAN535503 VSEL value
+ * @uv: microvolts DC to convert
+ *
+ * Returns the VSEL value necessary for the MAX8952 Regulator to
+ * generate an output voltage equal to or greater than @uv microvolts DC.
+ */
+static unsigned char omap_fan535503_uv_to_vsel(unsigned long uv)
+{
+	unsigned char vsel;
+	if (uv < 750000)
+		uv = 750000;
+	else if (uv > 1537500)
+		uv = 1537500;
+
+	vsel = DIV_ROUND_UP(uv - 750000, 12500);
+	return vsel | 0xC0;
+}
+
+/**
+ * omap_fan535508_uv_to_vsel - convert microvolts DC to FAN535508 VSEL value
+ * @uv: microvolts DC to convert
+ *
+ * Returns the VSEL value necessary for the MAX8952 Regulator to
+ * generate an output voltage equal to or greater than @uv microvolts DC.
+ */
+static unsigned char omap_fan535508_uv_to_vsel(unsigned long uv)
+{
+	unsigned char vsel;
+	if (uv < 750000)
+		uv = 750000;
+	else if (uv > 1437500)
+		uv = 1437500;
+
+	vsel = DIV_ROUND_UP(uv - 750000, 12500);
+	return vsel | 0xC0;
+}
+
+/* fan5335-core */
+static struct omap_voltdm_pmic omap4_fan_core = {
+	.slew_rate = 4000,
+	.step_size = 12500,
+	.vp_erroroffset = OMAP4_VP_CONFIG_ERROROFFSET,
+	.vp_vstepmin = OMAP4_VP_VSTEPMIN_VSTEPMIN,
+	.vp_vstepmax = OMAP4_VP_VSTEPMAX_VSTEPMAX,
+	.vddmin = 850000,
+	.vddmax = 1375000,
+	.vp_timeout_us = OMAP4_VP_VLIMITTO_TIMEOUT_US,
+	.i2c_slave_addr = 0x4A,
+	.i2c_high_speed = false,
+	.volt_reg_addr = 0x01,
+	.cmd_reg_addr = 0x01,
+	.vsel_to_uv = omap_fan535508_vsel_to_uv,
+	.uv_to_vsel = omap_fan535508_uv_to_vsel,
+};
+
+/* fan5335 iva */
+static struct omap_voltdm_pmic omap4_fan_iva = {
+	.slew_rate = 4000,
+	.step_size = 12500,
+	.vp_erroroffset = OMAP4_VP_CONFIG_ERROROFFSET,
+	.vp_vstepmin = OMAP4_VP_VSTEPMIN_VSTEPMIN,
+	.vp_vstepmax = OMAP4_VP_VSTEPMAX_VSTEPMAX,
+	.vddmin = 850000,
+	.vddmax = 1375000,
+	.vp_timeout_us = OMAP4_VP_VLIMITTO_TIMEOUT_US,
+	.i2c_slave_addr = 0x48,
+	.volt_reg_addr = 0x01,
+	.cmd_reg_addr = 0x01,
+	.i2c_high_speed = false,
+	.vsel_to_uv = omap_fan535503_vsel_to_uv,
+	.uv_to_vsel = omap_fan535503_uv_to_vsel,
+};
+
+int __init omap4_cpcap_init(void)
+{
+	struct voltagedomain *voltdm;
+
+	if (!of_find_compatible_node(NULL, NULL, "motorola,cpcap"))
+		return -ENODEV;
+
+	voltdm = voltdm_lookup("mpu");
+	omap_voltage_register_pmic(voltdm, &omap443x_max8952_mpu);
+
+	if (of_machine_is_compatible("motorola,droid-bionic")) {
+		voltdm = voltdm_lookup("mpu");
+		omap_voltage_register_pmic(voltdm, &omap_cpcap_core);
+
+		voltdm = voltdm_lookup("mpu");
+		omap_voltage_register_pmic(voltdm, &omap_cpcap_iva);
+	} else {
+		voltdm = voltdm_lookup("core");
+		omap_voltage_register_pmic(voltdm, &omap4_fan_core);
+
+		voltdm = voltdm_lookup("iva");
+		omap_voltage_register_pmic(voltdm, &omap4_fan_iva);
+	}
+
+	return 0;
+}
+
+static int __init cpcap_late_init(void)
+{
+	omap4_vc_set_pmic_signaling(PWRDM_POWER_RET);
+
+	return 0;
+}
+omap_late_initcall(cpcap_late_init);

arch/arm/mach-omap2/prm44xx.c

@@ -745,7 +745,7 @@ struct pwrdm_ops omap4_pwrdm_operations = {
 
 static int omap44xx_prm_late_init(void);
 
-void prm_save_context(void)
+static void prm_save_context(void)
 {
 	omap_prm_context.irq_enable =
 			omap4_prm_read_inst_reg(AM43XX_PRM_OCP_SOCKET_INST,
@@ -756,7 +756,7 @@ void prm_save_context(void)
 						omap4_prcm_irq_setup.pm_ctrl);
 }
 
-void prm_restore_context(void)
+static void prm_restore_context(void)
 {
 	omap4_prm_write_inst_reg(omap_prm_context.irq_enable,
 				 OMAP4430_PRM_OCP_SOCKET_INST,

arch/arm/mach-omap2/vc.c

@@ -26,6 +26,31 @@
 #include "scrm44xx.h"
 #include "control.h"
 
+#define OMAP4430_VDD_IVA_I2C_DISABLE		BIT(14)
+#define OMAP4430_VDD_MPU_I2C_DISABLE		BIT(13)
+#define OMAP4430_VDD_CORE_I2C_DISABLE		BIT(12)
+#define OMAP4430_VDD_IVA_PRESENCE		BIT(9)
+#define OMAP4430_VDD_MPU_PRESENCE		BIT(8)
+#define OMAP4430_AUTO_CTRL_VDD_IVA(x)		((x) << 4)
+#define OMAP4430_AUTO_CTRL_VDD_MPU(x)		((x) << 2)
+#define OMAP4430_AUTO_CTRL_VDD_CORE(x)		((x) << 0)
+#define OMAP4430_AUTO_CTRL_VDD_RET		2
+
+#define OMAP4430_VDD_I2C_DISABLE_MASK	\
+	(OMAP4430_VDD_IVA_I2C_DISABLE | \
+	 OMAP4430_VDD_MPU_I2C_DISABLE | \
+	 OMAP4430_VDD_CORE_I2C_DISABLE)
+
+#define OMAP4_VDD_DEFAULT_VAL	\
+	(OMAP4430_VDD_I2C_DISABLE_MASK | \
+	 OMAP4430_VDD_IVA_PRESENCE | OMAP4430_VDD_MPU_PRESENCE | \
+	 OMAP4430_AUTO_CTRL_VDD_IVA(OMAP4430_AUTO_CTRL_VDD_RET) | \
+	 OMAP4430_AUTO_CTRL_VDD_MPU(OMAP4430_AUTO_CTRL_VDD_RET) | \
+	 OMAP4430_AUTO_CTRL_VDD_CORE(OMAP4430_AUTO_CTRL_VDD_RET))
+
+#define OMAP4_VDD_RET_VAL	\
+	(OMAP4_VDD_DEFAULT_VAL & ~OMAP4430_VDD_I2C_DISABLE_MASK)
+
 /**
  * struct omap_vc_channel_cfg - describe the cfg_channel bitfield
  * @sa: bit for slave address
@@ -280,6 +305,26 @@ void omap3_vc_set_pmic_signaling(int core_next_state)
 	}
 }
 
+void omap4_vc_set_pmic_signaling(int core_next_state)
+{
+	struct voltagedomain *vd = vc.vd;
+	u32 val;
+
+	if (!vd)
+		return;
+
+	switch (core_next_state) {
+	case PWRDM_POWER_RET:
+		val = OMAP4_VDD_RET_VAL;
+		break;
+	default:
+		val = OMAP4_VDD_DEFAULT_VAL;
+		break;
+	}
+
+	vd->write(val, OMAP4_PRM_VOLTCTRL_OFFSET);
+}
+
 /*
  * Configure signal polarity for sys_clkreq and sys_off_mode pins
  * as the default values are wrong and can cause the system to hang
@@ -542,9 +587,19 @@ static void omap4_set_timings(struct voltagedomain *voltdm, bool off_mode)
 	writel_relaxed(val, OMAP4_SCRM_CLKSETUPTIME);
 }
 
+static void __init omap4_vc_init_pmic_signaling(struct voltagedomain *voltdm)
+{
+	if (vc.vd)
+		return;
+
+	vc.vd = voltdm;
+	voltdm->write(OMAP4_VDD_DEFAULT_VAL, OMAP4_PRM_VOLTCTRL_OFFSET);
+}
+
 /* OMAP4 specific voltage init functions */
 static void __init omap4_vc_init_channel(struct voltagedomain *voltdm)
 {
+	omap4_vc_init_pmic_signaling(voltdm);
 	omap4_set_timings(voltdm, true);
 	omap4_set_timings(voltdm, false);
 }
@@ -615,7 +670,7 @@ static void __init omap4_vc_i2c_timing_init(struct voltagedomain *voltdm)
 	const struct i2c_init_data *i2c_data;
 
 	if (!voltdm->pmic->i2c_high_speed) {
-		pr_warn("%s: only high speed supported!\n", __func__);
+		pr_info("%s: using bootloader low-speed timings\n", __func__);
 		return;
 	}
 

arch/arm/mach-omap2/vc.h

@@ -117,7 +117,7 @@ extern struct omap_vc_param omap4_iva_vc_data;
 extern struct omap_vc_param omap4_core_vc_data;
 
 void omap3_vc_set_pmic_signaling(int core_next_state);
-
+void omap4_vc_set_pmic_signaling(int core_next_state);
 
 void omap_vc_init_channel(struct voltagedomain *voltdm);
 int omap_vc_pre_scale(struct voltagedomain *voltdm,

drivers/clk/ti/clk-7xx.c

@@ -683,7 +683,7 @@ static const struct omap_clkctrl_reg_data dra7_l4per2_clkctrl_regs[] __initconst
 	{ DRA7_L4PER2_MCASP2_CLKCTRL, dra7_mcasp2_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:0154:22" },
 	{ DRA7_L4PER2_MCASP3_CLKCTRL, dra7_mcasp3_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:015c:22" },
 	{ DRA7_L4PER2_MCASP5_CLKCTRL, dra7_mcasp5_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:016c:22" },
-	{ DRA7_L4PER2_MCASP8_CLKCTRL, dra7_mcasp8_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:0184:24" },
+	{ DRA7_L4PER2_MCASP8_CLKCTRL, dra7_mcasp8_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:0184:22" },
 	{ DRA7_L4PER2_MCASP4_CLKCTRL, dra7_mcasp4_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:018c:22" },
 	{ DRA7_L4PER2_UART7_CLKCTRL, dra7_uart7_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:01c4:24" },
 	{ DRA7_L4PER2_UART8_CLKCTRL, dra7_uart8_bit_data, CLKF_SW_SUP, "l4per2-clkctrl:01d4:24" },
@@ -828,8 +828,8 @@ static struct ti_dt_clk dra7xx_clks[] = {
 	DT_CLK(NULL, "mcasp6_aux_gfclk_mux", "l4per2-clkctrl:01f8:22"),
 	DT_CLK(NULL, "mcasp7_ahclkx_mux", "l4per2-clkctrl:01fc:24"),
 	DT_CLK(NULL, "mcasp7_aux_gfclk_mux", "l4per2-clkctrl:01fc:22"),
-	DT_CLK(NULL, "mcasp8_ahclkx_mux", "l4per2-clkctrl:0184:22"),
-	DT_CLK(NULL, "mcasp8_aux_gfclk_mux", "l4per2-clkctrl:0184:24"),
+	DT_CLK(NULL, "mcasp8_ahclkx_mux", "l4per2-clkctrl:0184:24"),
+	DT_CLK(NULL, "mcasp8_aux_gfclk_mux", "l4per2-clkctrl:0184:22"),
 	DT_CLK(NULL, "mmc1_clk32k", "l3init-clkctrl:0008:8"),
 	DT_CLK(NULL, "mmc1_fclk_div", "l3init-clkctrl:0008:25"),
 	DT_CLK(NULL, "mmc1_fclk_mux", "l3init-clkctrl:0008:24"),