Merge tag 'riscv-dt-for-v6.6' of...

Merge tag 'riscv-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux into soc/dt

RISC-V Devicetrees for v6.6

StarFive:
There's only StarFive stuff this time around, starting with some
bindings to get clock ID defines out of the binding headers. Getting
these (and the syscon bindings) in unblocked a swathe of stuff sitting
on the list. Added are: new clock controllers and sycons, ethernet
support, thermal sensors, USB and PCIe PHYs, hwrng, mmc and a few more
besides for the VisionFive v2. The original VisionFive and BeagleV
Starlight got some the thermal sensor support too, as that is supported
by the same driver. These changes make the board actually usable with
something other than an initramfs.
Overlay support by way of the -@ flag set during dtb building, is added
also.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>

* tag 'riscv-dt-for-v6.6' of https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux: (26 commits)
  riscv: dts: starfive: jh7110: Fix GMAC configuration
  riscv: dts: starfive - Add hwrng node for JH7110 SoC
  riscv: dts: starfive - Add crypto and DMA node for JH7110
  riscv: dts: starfive: Add mmc nodes on VisionFive 2 board
  riscv: dts: starfive: enable DCDC1&ALDO4 node in axp15060
  riscv: dts: starfive: Add QSPI controller node for StarFive JH7110 SoC
  riscv: dts: starfive: jh7110: add the node and pins configuration for tdm
  riscv: dts: starfive: jh7110: add dma controller node
  riscv: dts: starfive: Add spi node and pins configuration
  riscv: dts: starfive: Add USB dts node for JH7110
  riscv: dts: starfive: Add USB and PCIe PHY nodes for JH7110
  riscv: dts: starfive: jh7110: Add temperature sensor node and thermal-zones
  riscv: dts: starfive: jh7100: Add temperature sensor node and thermal-zones
  riscv: dts: starfive: visionfive 2: Add configuration of gmac and phy
  riscv: dts: starfive: jh7110: Add ethernet device nodes
  riscv: dts: starfive: jh7110: Add PLL clocks source in SYSCRG node
  riscv: dts: starfive: jh7110: Add syscon nodes
  riscv: dts: starfive: jh7110: Add STGCRG/ISPCRG/VOUTCRG nodes
  riscv: dts: starfive: jh7110: Add DVP and HDMI TX pixel external clocks
  dt-bindings: clock: Add StarFive JH7110 Video-Output clock and reset generator
  ...

Link: https://lore.kernel.org/r/20230813-naturist-fragment-ac7d10c453ba@spudSigned-off-by: Arnd Bergmann <arnd@arndb.de>

Documentation/devicetree/bindings/clock/starfive,jh7110-ispcrg.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/starfive,jh7110-ispcrg.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7110 Image-Signal-Process Clock and Reset Generator
+
+maintainers:
+  - Xingyu Wu <xingyu.wu@starfivetech.com>
+
+properties:
+  compatible:
+    const: starfive,jh7110-ispcrg
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: ISP Top core
+      - description: ISP Top Axi
+      - description: NOC ISP Bus
+      - description: external DVP
+
+  clock-names:
+    items:
+      - const: isp_top_core
+      - const: isp_top_axi
+      - const: noc_bus_isp_axi
+      - const: dvp_clk
+
+  resets:
+    items:
+      - description: ISP Top core
+      - description: ISP Top Axi
+      - description: NOC ISP Bus
+
+  '#clock-cells':
+    const: 1
+    description:
+      See <dt-bindings/clock/starfive,jh7110-crg.h> for valid indices.
+
+  '#reset-cells':
+    const: 1
+    description:
+      See <dt-bindings/reset/starfive,jh7110-crg.h> for valid indices.
+
+  power-domains:
+    maxItems: 1
+    description:
+      ISP domain power
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - resets
+  - '#clock-cells'
+  - '#reset-cells'
+  - power-domains
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/starfive,jh7110-crg.h>
+    #include <dt-bindings/power/starfive,jh7110-pmu.h>
+    #include <dt-bindings/reset/starfive,jh7110-crg.h>
+
+    ispcrg: clock-controller@19810000 {
+        compatible = "starfive,jh7110-ispcrg";
+        reg = <0x19810000 0x10000>;
+        clocks = <&syscrg JH7110_SYSCLK_ISP_TOP_CORE>,
+                 <&syscrg JH7110_SYSCLK_ISP_TOP_AXI>,
+                 <&syscrg JH7110_SYSCLK_NOC_BUS_ISP_AXI>,
+                 <&dvp_clk>;
+        clock-names = "isp_top_core", "isp_top_axi",
+                      "noc_bus_isp_axi", "dvp_clk";
+        resets = <&syscrg JH7110_SYSRST_ISP_TOP>,
+                 <&syscrg JH7110_SYSRST_ISP_TOP_AXI>,
+                 <&syscrg JH7110_SYSRST_NOC_BUS_ISP_AXI>;
+        #clock-cells = <1>;
+        #reset-cells = <1>;
+        power-domains = <&pwrc JH7110_PD_ISP>;
+    };

Documentation/devicetree/bindings/clock/starfive,jh7110-pll.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/starfive,jh7110-pll.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7110 PLL Clock Generator
+
+description:
+  These PLLs are high speed, low jitter frequency synthesizers in the JH7110.
+  Each PLL works in integer mode or fraction mode, with configuration
+  registers in the sys syscon. So the PLLs node should be a child of
+  SYS-SYSCON node.
+  The formula for calculating frequency is
+  Fvco = Fref * (NI + NF) / M / Q1
+
+maintainers:
+  - Xingyu Wu <xingyu.wu@starfivetech.com>
+
+properties:
+  compatible:
+    const: starfive,jh7110-pll
+
+  clocks:
+    maxItems: 1
+    description: Main Oscillator (24 MHz)
+
+  '#clock-cells':
+    const: 1
+    description:
+      See <dt-bindings/clock/starfive,jh7110-crg.h> for valid indices.
+
+required:
+  - compatible
+  - clocks
+  - '#clock-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    clock-controller {
+      compatible = "starfive,jh7110-pll";
+      clocks = <&osc>;
+      #clock-cells = <1>;
+    };

Documentation/devicetree/bindings/clock/starfive,jh7110-stgcrg.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/starfive,jh7110-stgcrg.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7110 System-Top-Group Clock and Reset Generator
+
+maintainers:
+  - Xingyu Wu <xingyu.wu@starfivetech.com>
+
+properties:
+  compatible:
+    const: starfive,jh7110-stgcrg
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Main Oscillator (24 MHz)
+      - description: HIFI4 core
+      - description: STG AXI/AHB
+      - description: USB (125 MHz)
+      - description: CPU Bus
+      - description: HIFI4 Axi
+      - description: NOC STG Bus
+      - description: APB Bus
+
+  clock-names:
+    items:
+      - const: osc
+      - const: hifi4_core
+      - const: stg_axiahb
+      - const: usb_125m
+      - const: cpu_bus
+      - const: hifi4_axi
+      - const: nocstg_bus
+      - const: apb_bus
+
+  '#clock-cells':
+    const: 1
+    description:
+      See <dt-bindings/clock/starfive,jh7110-crg.h> for valid indices.
+
+  '#reset-cells':
+    const: 1
+    description:
+      See <dt-bindings/reset/starfive,jh7110-crg.h> for valid indices.
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - '#clock-cells'
+  - '#reset-cells'
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/starfive,jh7110-crg.h>
+
+    stgcrg: clock-controller@10230000 {
+        compatible = "starfive,jh7110-stgcrg";
+        reg = <0x10230000 0x10000>;
+        clocks = <&osc>,
+                 <&syscrg JH7110_SYSCLK_HIFI4_CORE>,
+                 <&syscrg JH7110_SYSCLK_STG_AXIAHB>,
+                 <&syscrg JH7110_SYSCLK_USB_125M>,
+                 <&syscrg JH7110_SYSCLK_CPU_BUS>,
+                 <&syscrg JH7110_SYSCLK_HIFI4_AXI>,
+                 <&syscrg JH7110_SYSCLK_NOCSTG_BUS>,
+                 <&syscrg JH7110_SYSCLK_APB_BUS>;
+        clock-names = "osc", "hifi4_core",
+                      "stg_axiahb", "usb_125m",
+                      "cpu_bus", "hifi4_axi",
+                      "nocstg_bus", "apb_bus";
+        #clock-cells = <1>;
+        #reset-cells = <1>;
+    };

Documentation/devicetree/bindings/clock/starfive,jh7110-syscrg.yaml

@@ -27,6 +27,9 @@ properties:
           - description: External I2S RX left/right channel clock
           - description: External TDM clock
           - description: External audio master clock
+          - description: PLL0
+          - description: PLL1
+          - description: PLL2
 
       - items:
           - description: Main Oscillator (24 MHz)
@@ -38,6 +41,9 @@ properties:
           - description: External I2S RX left/right channel clock
           - description: External TDM clock
           - description: External audio master clock
+          - description: PLL0
+          - description: PLL1
+          - description: PLL2
 
   clock-names:
     oneOf:
@@ -52,6 +58,9 @@ properties:
           - const: i2srx_lrck_ext
           - const: tdm_ext
           - const: mclk_ext
+          - const: pll0_out
+          - const: pll1_out
+          - const: pll2_out
 
       - items:
           - const: osc
@@ -63,6 +72,9 @@ properties:
           - const: i2srx_lrck_ext
           - const: tdm_ext
           - const: mclk_ext
+          - const: pll0_out
+          - const: pll1_out
+          - const: pll2_out
 
   '#clock-cells':
     const: 1
@@ -93,12 +105,14 @@ examples:
                  <&gmac1_rgmii_rxin>,
                  <&i2stx_bclk_ext>, <&i2stx_lrck_ext>,
                  <&i2srx_bclk_ext>, <&i2srx_lrck_ext>,
-                 <&tdm_ext>, <&mclk_ext>;
+                 <&tdm_ext>, <&mclk_ext>,
+                 <&pllclk 0>, <&pllclk 1>, <&pllclk 2>;
         clock-names = "osc", "gmac1_rmii_refin",
                       "gmac1_rgmii_rxin",
                       "i2stx_bclk_ext", "i2stx_lrck_ext",
                       "i2srx_bclk_ext", "i2srx_lrck_ext",
-                      "tdm_ext", "mclk_ext";
+                      "tdm_ext", "mclk_ext",
+                      "pll0_out", "pll1_out", "pll2_out";
         #clock-cells = <1>;
         #reset-cells = <1>;
     };

Documentation/devicetree/bindings/clock/starfive,jh7110-voutcrg.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/clock/starfive,jh7110-voutcrg.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7110 Video-Output Clock and Reset Generator
+
+maintainers:
+  - Xingyu Wu <xingyu.wu@starfivetech.com>
+
+properties:
+  compatible:
+    const: starfive,jh7110-voutcrg
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: Vout Top core
+      - description: Vout Top Ahb
+      - description: Vout Top Axi
+      - description: Vout Top HDMI MCLK
+      - description: I2STX0 BCLK
+      - description: external HDMI pixel
+
+  clock-names:
+    items:
+      - const: vout_src
+      - const: vout_top_ahb
+      - const: vout_top_axi
+      - const: vout_top_hdmitx0_mclk
+      - const: i2stx0_bclk
+      - const: hdmitx0_pixelclk
+
+  resets:
+    maxItems: 1
+    description: Vout Top core
+
+  '#clock-cells':
+    const: 1
+    description:
+      See <dt-bindings/clock/starfive,jh7110-crg.h> for valid indices.
+
+  '#reset-cells':
+    const: 1
+    description:
+      See <dt-bindings/reset/starfive,jh7110-crg.h> for valid indices.
+
+  power-domains:
+    maxItems: 1
+    description:
+      Vout domain power
+
+required:
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - resets
+  - '#clock-cells'
+  - '#reset-cells'
+  - power-domains
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/starfive,jh7110-crg.h>
+    #include <dt-bindings/power/starfive,jh7110-pmu.h>
+    #include <dt-bindings/reset/starfive,jh7110-crg.h>
+
+    voutcrg: clock-controller@295C0000 {
+        compatible = "starfive,jh7110-voutcrg";
+        reg = <0x295C0000 0x10000>;
+        clocks = <&syscrg JH7110_SYSCLK_VOUT_SRC>,
+                 <&syscrg JH7110_SYSCLK_VOUT_TOP_AHB>,
+                 <&syscrg JH7110_SYSCLK_VOUT_TOP_AXI>,
+                 <&syscrg JH7110_SYSCLK_VOUT_TOP_HDMITX0_MCLK>,
+                 <&syscrg JH7110_SYSCLK_I2STX0_BCLK>,
+                 <&hdmitx0_pixelclk>;
+        clock-names = "vout_src", "vout_top_ahb",
+                      "vout_top_axi", "vout_top_hdmitx0_mclk",
+                      "i2stx0_bclk", "hdmitx0_pixelclk";
+        resets = <&syscrg JH7110_SYSRST_VOUT_TOP_SRC>;
+        #clock-cells = <1>;
+        #reset-cells = <1>;
+        power-domains = <&pwrc JH7110_PD_VOUT>;
+    };

Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-syscon.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/soc/starfive/starfive,jh7110-syscon.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7110 SoC system controller
+
+maintainers:
+  - William Qiu <william.qiu@starfivetech.com>
+
+description:
+  The StarFive JH7110 SoC system controller provides register information such
+  as offset, mask and shift to configure related modules such as MMC and PCIe.
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - const: starfive,jh7110-sys-syscon
+          - const: syscon
+          - const: simple-mfd
+      - items:
+          - enum:
+              - starfive,jh7110-aon-syscon
+              - starfive,jh7110-stg-syscon
+          - const: syscon
+
+  reg:
+    maxItems: 1
+
+  clock-controller:
+    $ref: /schemas/clock/starfive,jh7110-pll.yaml#
+    type: object
+
+  "#power-domain-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: starfive,jh7110-sys-syscon
+    then:
+      required:
+        - clock-controller
+    else:
+      properties:
+        clock-controller: false
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: starfive,jh7110-aon-syscon
+    then:
+      required:
+        - "#power-domain-cells"
+    else:
+      properties:
+        "#power-domain-cells": false
+
+additionalProperties: false
+
+examples:
+  - |
+    syscon@10240000 {
+        compatible = "starfive,jh7110-stg-syscon", "syscon";
+        reg = <0x10240000 0x1000>;
+    };
+
+    syscon@13030000 {
+        compatible = "starfive,jh7110-sys-syscon", "syscon", "simple-mfd";
+        reg = <0x13030000 0x1000>;
+
+        clock-controller {
+            compatible = "starfive,jh7110-pll";
+            clocks = <&osc>;
+            #clock-cells = <1>;
+        };
+    };
+
+    syscon@17010000 {
+        compatible = "starfive,jh7110-aon-syscon", "syscon";
+        reg = <0x17010000 0x1000>;
+        #power-domain-cells = <1>;
+    };
+
+...

MAINTAINERS

@@ -20282,6 +20282,12 @@ S:	Supported
 F:	Documentation/devicetree/bindings/mmc/starfive*
 F:	drivers/mmc/host/dw_mmc-starfive.c
 
+STARFIVE JH7110 SYSCON
+M:	William Qiu <william.qiu@starfivetech.com>
+M:	Xingyu Wu <xingyu.wu@starfivetech.com>
+S:	Supported
+F:	Documentation/devicetree/bindings/soc/starfive/starfive,jh7110-syscon.yaml
+
 STARFIVE JH7110 TDM DRIVER
 M:	Walker Chen <walker.chen@starfivetech.com>
 S:	Maintained
@@ -20331,6 +20337,7 @@ STARFIVE SOC DRIVERS
 M:	Conor Dooley <conor@kernel.org>
 S:	Maintained
 T:	git https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux.git/
+F:	Documentation/devicetree/bindings/soc/starfive/
 F:	drivers/soc/starfive/
 
 STARFIVE TRNG DRIVER

arch/riscv/boot/dts/starfive/Makefile

 # SPDX-License-Identifier: GPL-2.0
+# Enables support for device-tree overlays
+DTC_FLAGS_jh7100-beaglev-starlight := -@
+DTC_FLAGS_jh7100-starfive-visionfive-v1 := -@
+DTC_FLAGS_jh7110-starfive-visionfive-2-v1.2a := -@
+DTC_FLAGS_jh7110-starfive-visionfive-2-v1.3b := -@
+
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-beaglev-starlight.dtb
 dtb-$(CONFIG_ARCH_STARFIVE) += jh7100-starfive-visionfive-v1.dtb
 

arch/riscv/boot/dts/starfive/jh7100.dtsi

@@ -80,6 +80,31 @@ core1 {
 		};
 	};
 
+	thermal-zones {
+		cpu-thermal {
+			polling-delay-passive = <250>;
+			polling-delay = <15000>;
+
+			thermal-sensors = <&sfctemp>;
+
+			trips {
+				cpu_alert0 {
+					/* milliCelsius */
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit {
+					/* milliCelsius */
+					temperature = <90000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
 	osc_sys: osc_sys {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
@@ -248,5 +273,17 @@ watchdog@12480000 {
 			resets = <&rstgen JH7100_RSTN_WDTIMER_APB>,
 				 <&rstgen JH7100_RSTN_WDT>;
 		};
+
+		sfctemp: temperature-sensor@124a0000 {
+			compatible = "starfive,jh7100-temp";
+			reg = <0x0 0x124a0000 0x0 0x10000>;
+			clocks = <&clkgen JH7100_CLK_TEMP_SENSE>,
+				 <&clkgen JH7100_CLK_TEMP_APB>;
+			clock-names = "sense", "bus";
+			resets = <&rstgen JH7100_RSTN_TEMP_SENSE>,
+				 <&rstgen JH7100_RSTN_TEMP_APB>;
+			reset-names = "sense", "bus";
+			#thermal-sensor-cells = <0>;
+		};
 	};
 };

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.2a.dts

@@ -11,3 +11,16 @@ / {
 	model = "StarFive VisionFive 2 v1.2A";
 	compatible = "starfive,visionfive-2-v1.2a", "starfive,jh7110";
 };
+
+&gmac1 {
+	phy-mode = "rmii";
+	assigned-clocks = <&syscrg JH7110_SYSCLK_GMAC1_TX>,
+			  <&syscrg JH7110_SYSCLK_GMAC1_RX>;
+	assigned-clock-parents = <&syscrg JH7110_SYSCLK_GMAC1_RMII_RTX>,
+				 <&syscrg JH7110_SYSCLK_GMAC1_RMII_RTX>;
+};
+
+&phy0 {
+	rx-internal-delay-ps = <1900>;
+	tx-internal-delay-ps = <1350>;
+};

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2-v1.3b.dts

@@ -11,3 +11,34 @@ / {
 	model = "StarFive VisionFive 2 v1.3B";
 	compatible = "starfive,visionfive-2-v1.3b", "starfive,jh7110";
 };
+
+&gmac0 {
+	starfive,tx-use-rgmii-clk;
+	assigned-clocks = <&aoncrg JH7110_AONCLK_GMAC0_TX>;
+	assigned-clock-parents = <&aoncrg JH7110_AONCLK_GMAC0_RMII_RTX>;
+};
+
+&gmac1 {
+	starfive,tx-use-rgmii-clk;
+	assigned-clocks = <&syscrg JH7110_SYSCLK_GMAC1_TX>;
+	assigned-clock-parents = <&syscrg JH7110_SYSCLK_GMAC1_RMII_RTX>;
+};
+
+&phy0 {
+	motorcomm,tx-clk-adj-enabled;
+	motorcomm,tx-clk-100-inverted;
+	motorcomm,tx-clk-1000-inverted;
+	motorcomm,rx-clk-drv-microamp = <3970>;
+	motorcomm,rx-data-drv-microamp = <2910>;
+	rx-internal-delay-ps = <1500>;
+	tx-internal-delay-ps = <1500>;
+};
+
+&phy1 {
+	motorcomm,tx-clk-adj-enabled;
+	motorcomm,tx-clk-100-inverted;
+	motorcomm,rx-clk-drv-microamp = <3970>;
+	motorcomm,rx-data-drv-microamp = <2910>;
+	rx-internal-delay-ps = <300>;
+	tx-internal-delay-ps = <0>;
+};

arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi

@@ -11,10 +11,14 @@
 
 / {
 	aliases {
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac1;
 		i2c0 = &i2c0;
 		i2c2 = &i2c2;
 		i2c5 = &i2c5;
 		i2c6 = &i2c6;
+		mmc0 = &mmc0;
+		mmc1 = &mmc1;
 		serial0 = &uart0;
 	};
 
@@ -38,6 +42,10 @@ gpio-restart {
 	};
 };
 
+&dvp_clk {
+	clock-frequency = <74250000>;
+};
+
 &gmac0_rgmii_rxin {
 	clock-frequency = <125000000>;
 };
@@ -54,6 +62,10 @@ &gmac1_rmii_refin {
 	clock-frequency = <50000000>;
 };
 
+&hdmitx0_pixelclk {
+	clock-frequency = <297000000>;
+};
+
 &i2srx_bclk_ext {
 	clock-frequency = <12288000>;
 };
@@ -86,6 +98,38 @@ &tdm_ext {
 	clock-frequency = <49152000>;
 };
 
+&gmac0 {
+	phy-handle = <&phy0>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&gmac1 {
+	phy-handle = <&phy1>;
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "snps,dwmac-mdio";
+
+		phy1: ethernet-phy@1 {
+			reg = <0>;
+		};
+	};
+};
+
 &i2c0 {
 	clock-frequency = <100000>;
 	i2c-sda-hold-time-ns = <300>;
@@ -123,12 +167,28 @@ axp15060: pmic@36 {
 		#interrupt-cells = <1>;
 
 		regulators {
+			vcc_3v3: dcdc1 {
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_3v3";
+			};
+
 			vdd_cpu: dcdc2 {
 				regulator-always-on;
 				regulator-min-microvolt = <500000>;
 				regulator-max-microvolt = <1540000>;
 				regulator-name = "vdd-cpu";
 			};
+
+			emmc_vdd: aldo4 {
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "emmc_vdd";
+			};
 		};
 	};
 };
@@ -143,6 +203,83 @@ &i2c6 {
 	status = "okay";
 };
 
+&mmc0 {
+	max-frequency = <100000000>;
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	non-removable;
+	cap-mmc-hw-reset;
+	post-power-on-delay-ms = <200>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&emmc_vdd>;
+	status = "okay";
+};
+
+&mmc1 {
+	max-frequency = <100000000>;
+	bus-width = <4>;
+	no-sdio;
+	no-mmc;
+	broken-cd;
+	cap-sd-highspeed;
+	post-power-on-delay-ms = <200>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	status = "okay";
+};
+
+&qspi {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	nor_flash: flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		cdns,read-delay = <5>;
+		spi-max-frequency = <12000000>;
+		cdns,tshsl-ns = <1>;
+		cdns,tsd2d-ns = <1>;
+		cdns,tchsh-ns = <1>;
+		cdns,tslch-ns = <1>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			spl@0 {
+				reg = <0x0 0x80000>;
+			};
+			uboot-env@f0000 {
+				reg = <0xf0000 0x10000>;
+			};
+			uboot@100000 {
+				reg = <0x100000 0x400000>;
+			};
+			reserved-data@600000 {
+				reg = <0x600000 0x1000000>;
+			};
+		};
+	};
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+	status = "okay";
+
+	spi_dev0: spi@0 {
+		compatible = "rohm,dh2228fv";
+		reg = <0>;
+		spi-max-frequency = <10000000>;
+	};
+};
+
 &sysgpio {
 	i2c0_pins: i2c0-0 {
 		i2c-pins {
@@ -200,6 +337,109 @@ GPOEN_SYS_I2C6_DATA,
 		};
 	};
 
+	mmc0_pins: mmc0-0 {
+		 rst-pins {
+			pinmux = <GPIOMUX(62, GPOUT_SYS_SDIO0_RST,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+
+		mmc-pins {
+			pinmux = <PINMUX(64, 0)>,
+				 <PINMUX(65, 0)>,
+				 <PINMUX(66, 0)>,
+				 <PINMUX(67, 0)>,
+				 <PINMUX(68, 0)>,
+				 <PINMUX(69, 0)>,
+				 <PINMUX(70, 0)>,
+				 <PINMUX(71, 0)>,
+				 <PINMUX(72, 0)>,
+				 <PINMUX(73, 0)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-enable;
+		};
+	};
+
+	mmc1_pins: mmc1-0 {
+		clk-pins {
+			pinmux = <GPIOMUX(10, GPOUT_SYS_SDIO1_CLK,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+
+		mmc-pins {
+			pinmux = <GPIOMUX(9, GPOUT_SYS_SDIO1_CMD,
+					     GPOEN_SYS_SDIO1_CMD,
+					     GPI_SYS_SDIO1_CMD)>,
+				 <GPIOMUX(11, GPOUT_SYS_SDIO1_DATA0,
+					      GPOEN_SYS_SDIO1_DATA0,
+					      GPI_SYS_SDIO1_DATA0)>,
+				 <GPIOMUX(12, GPOUT_SYS_SDIO1_DATA1,
+					      GPOEN_SYS_SDIO1_DATA1,
+					      GPI_SYS_SDIO1_DATA1)>,
+				 <GPIOMUX(7, GPOUT_SYS_SDIO1_DATA2,
+					     GPOEN_SYS_SDIO1_DATA2,
+					     GPI_SYS_SDIO1_DATA2)>,
+				 <GPIOMUX(8, GPOUT_SYS_SDIO1_DATA3,
+					     GPOEN_SYS_SDIO1_DATA3,
+					     GPI_SYS_SDIO1_DATA3)>;
+			bias-pull-up;
+			drive-strength = <12>;
+			input-enable;
+			input-schmitt-enable;
+			slew-rate = <0>;
+		};
+	};
+
+	spi0_pins: spi0-0 {
+		mosi-pins {
+			pinmux = <GPIOMUX(52, GPOUT_SYS_SPI0_TXD,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-disable;
+			input-disable;
+			input-schmitt-disable;
+		};
+
+		miso-pins {
+			pinmux = <GPIOMUX(53, GPOUT_LOW,
+					      GPOEN_DISABLE,
+					      GPI_SYS_SPI0_RXD)>;
+			bias-pull-up;
+			input-enable;
+			input-schmitt-enable;
+		};
+
+		sck-pins {
+			pinmux = <GPIOMUX(48, GPOUT_SYS_SPI0_CLK,
+					      GPOEN_ENABLE,
+					      GPI_SYS_SPI0_CLK)>;
+			bias-disable;
+			input-disable;
+			input-schmitt-disable;
+		};
+
+		ss-pins {
+			pinmux = <GPIOMUX(48, GPOUT_SYS_SPI0_FSS,
+					      GPOEN_ENABLE,
+					      GPI_SYS_SPI0_FSS)>;
+			bias-disable;
+			input-disable;
+			input-schmitt-disable;
+		};
+	};
+
 	uart0_pins: uart0-0 {
 		tx-pins {
 			pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
@@ -223,6 +463,46 @@ GPOEN_DISABLE,
 			slew-rate = <0>;
 		};
 	};
+
+	tdm_pins: tdm-0 {
+		tx-pins {
+			pinmux = <GPIOMUX(44, GPOUT_SYS_TDM_TXD,
+					      GPOEN_ENABLE,
+					      GPI_NONE)>;
+			bias-pull-up;
+			drive-strength = <2>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+
+		rx-pins {
+			pinmux = <GPIOMUX(61, GPOUT_HIGH,
+					      GPOEN_DISABLE,
+					      GPI_SYS_TDM_RXD)>;
+			input-enable;
+		};
+
+		sync-pins {
+			pinmux = <GPIOMUX(63, GPOUT_HIGH,
+					      GPOEN_DISABLE,
+					      GPI_SYS_TDM_SYNC)>;
+			input-enable;
+		};
+
+		pcmclk-pins {
+			pinmux = <GPIOMUX(38, GPOUT_HIGH,
+					      GPOEN_DISABLE,
+					      GPI_SYS_TDM_CLK)>;
+			input-enable;
+		};
+	};
+};
+
+&tdm {
+	pinctrl-names = "default";
+	pinctrl-0 = <&tdm_pins>;
+	status = "okay";
 };
 
 &uart0 {
@@ -231,6 +511,10 @@ &uart0 {
 	status = "okay";
 };
 
+&usb0 {
+	dr_mode = "peripheral";
+};
+
 &U74_1 {
 	cpu-supply = <&vdd_cpu>;
 };

include/dt-bindings/clock/starfive,jh7110-crg.h

 /* SPDX-License-Identifier: GPL-2.0 OR MIT */
 /*
  * Copyright 2022 Emil Renner Berthing <kernel@esmil.dk>
+ * Copyright 2022 StarFive Technology Co., Ltd.
  */
 
 #ifndef __DT_BINDINGS_CLOCK_STARFIVE_JH7110_CRG_H__
 #define __DT_BINDINGS_CLOCK_STARFIVE_JH7110_CRG_H__
 
+/* PLL clocks */
+#define JH7110_PLLCLK_PLL0_OUT			0
+#define JH7110_PLLCLK_PLL1_OUT			1
+#define JH7110_PLLCLK_PLL2_OUT			2
+#define JH7110_PLLCLK_END			3
+
 /* SYSCRG clocks */
 #define JH7110_SYSCLK_CPU_ROOT			0
 #define JH7110_SYSCLK_CPU_CORE			1
@@ -218,4 +225,77 @@
 
 #define JH7110_AONCLK_END			14
 
+/* STGCRG clocks */
+#define JH7110_STGCLK_HIFI4_CLK_CORE		0
+#define JH7110_STGCLK_USB0_APB			1
+#define JH7110_STGCLK_USB0_UTMI_APB		2
+#define JH7110_STGCLK_USB0_AXI			3
+#define JH7110_STGCLK_USB0_LPM			4
+#define JH7110_STGCLK_USB0_STB			5
+#define JH7110_STGCLK_USB0_APP_125		6
+#define JH7110_STGCLK_USB0_REFCLK		7
+#define JH7110_STGCLK_PCIE0_AXI_MST0		8
+#define JH7110_STGCLK_PCIE0_APB			9
+#define JH7110_STGCLK_PCIE0_TL			10
+#define JH7110_STGCLK_PCIE1_AXI_MST0		11
+#define JH7110_STGCLK_PCIE1_APB			12
+#define JH7110_STGCLK_PCIE1_TL			13
+#define JH7110_STGCLK_PCIE_SLV_MAIN		14
+#define JH7110_STGCLK_SEC_AHB			15
+#define JH7110_STGCLK_SEC_MISC_AHB		16
+#define JH7110_STGCLK_GRP0_MAIN			17
+#define JH7110_STGCLK_GRP0_BUS			18
+#define JH7110_STGCLK_GRP0_STG			19
+#define JH7110_STGCLK_GRP1_MAIN			20
+#define JH7110_STGCLK_GRP1_BUS			21
+#define JH7110_STGCLK_GRP1_STG			22
+#define JH7110_STGCLK_GRP1_HIFI			23
+#define JH7110_STGCLK_E2_RTC			24
+#define JH7110_STGCLK_E2_CORE			25
+#define JH7110_STGCLK_E2_DBG			26
+#define JH7110_STGCLK_DMA1P_AXI			27
+#define JH7110_STGCLK_DMA1P_AHB			28
+
+#define JH7110_STGCLK_END			29
+
+/* ISPCRG clocks */
+#define JH7110_ISPCLK_DOM4_APB_FUNC		0
+#define JH7110_ISPCLK_MIPI_RX0_PXL		1
+#define JH7110_ISPCLK_DVP_INV			2
+#define JH7110_ISPCLK_M31DPHY_CFG_IN		3
+#define JH7110_ISPCLK_M31DPHY_REF_IN		4
+#define JH7110_ISPCLK_M31DPHY_TX_ESC_LAN0	5
+#define JH7110_ISPCLK_VIN_APB			6
+#define JH7110_ISPCLK_VIN_SYS			7
+#define JH7110_ISPCLK_VIN_PIXEL_IF0		8
+#define JH7110_ISPCLK_VIN_PIXEL_IF1		9
+#define JH7110_ISPCLK_VIN_PIXEL_IF2		10
+#define JH7110_ISPCLK_VIN_PIXEL_IF3		11
+#define JH7110_ISPCLK_VIN_P_AXI_WR		12
+#define JH7110_ISPCLK_ISPV2_TOP_WRAPPER_C	13
+
+#define JH7110_ISPCLK_END			14
+
+/* VOUTCRG clocks */
+#define JH7110_VOUTCLK_APB			0
+#define JH7110_VOUTCLK_DC8200_PIX		1
+#define JH7110_VOUTCLK_DSI_SYS			2
+#define JH7110_VOUTCLK_TX_ESC			3
+#define JH7110_VOUTCLK_DC8200_AXI		4
+#define JH7110_VOUTCLK_DC8200_CORE		5
+#define JH7110_VOUTCLK_DC8200_AHB		6
+#define JH7110_VOUTCLK_DC8200_PIX0		7
+#define JH7110_VOUTCLK_DC8200_PIX1		8
+#define JH7110_VOUTCLK_DOM_VOUT_TOP_LCD		9
+#define JH7110_VOUTCLK_DSITX_APB		10
+#define JH7110_VOUTCLK_DSITX_SYS		11
+#define JH7110_VOUTCLK_DSITX_DPI		12
+#define JH7110_VOUTCLK_DSITX_TXESC		13
+#define JH7110_VOUTCLK_MIPITX_DPHY_TXESC	14
+#define JH7110_VOUTCLK_HDMI_TX_MCLK		15
+#define JH7110_VOUTCLK_HDMI_TX_BCLK		16
+#define JH7110_VOUTCLK_HDMI_TX_SYS		17
+
+#define JH7110_VOUTCLK_END			18
+
 #endif /* __DT_BINDINGS_CLOCK_STARFIVE_JH7110_CRG_H__ */

include/dt-bindings/reset/starfive,jh7110-crg.h

 /* SPDX-License-Identifier: GPL-2.0 OR MIT */
 /*
  * Copyright (C) 2022 Emil Renner Berthing <kernel@esmil.dk>
+ * Copyright (C) 2022 StarFive Technology Co., Ltd.
  */
 
 #ifndef __DT_BINDINGS_RESET_STARFIVE_JH7110_CRG_H__
@@ -151,4 +152,63 @@
 
 #define JH7110_AONRST_END			8
 
+/* STGCRG resets */
+#define JH7110_STGRST_SYSCON			0
+#define JH7110_STGRST_HIFI4_CORE		1
+#define JH7110_STGRST_HIFI4_AXI			2
+#define JH7110_STGRST_SEC_AHB			3
+#define JH7110_STGRST_E24_CORE			4
+#define JH7110_STGRST_DMA1P_AXI			5
+#define JH7110_STGRST_DMA1P_AHB			6
+#define JH7110_STGRST_USB0_AXI			7
+#define JH7110_STGRST_USB0_APB			8
+#define JH7110_STGRST_USB0_UTMI_APB		9
+#define JH7110_STGRST_USB0_PWRUP		10
+#define JH7110_STGRST_PCIE0_AXI_MST0		11
+#define JH7110_STGRST_PCIE0_AXI_SLV0		12
+#define JH7110_STGRST_PCIE0_AXI_SLV		13
+#define JH7110_STGRST_PCIE0_BRG			14
+#define JH7110_STGRST_PCIE0_CORE		15
+#define JH7110_STGRST_PCIE0_APB			16
+#define JH7110_STGRST_PCIE1_AXI_MST0		17
+#define JH7110_STGRST_PCIE1_AXI_SLV0		18
+#define JH7110_STGRST_PCIE1_AXI_SLV		19
+#define JH7110_STGRST_PCIE1_BRG			20
+#define JH7110_STGRST_PCIE1_CORE		21
+#define JH7110_STGRST_PCIE1_APB			22
+
+#define JH7110_STGRST_END			23
+
+/* ISPCRG resets */
+#define JH7110_ISPRST_ISPV2_TOP_WRAPPER_P	0
+#define JH7110_ISPRST_ISPV2_TOP_WRAPPER_C	1
+#define JH7110_ISPRST_M31DPHY_HW		2
+#define JH7110_ISPRST_M31DPHY_B09_AON		3
+#define JH7110_ISPRST_VIN_APB			4
+#define JH7110_ISPRST_VIN_PIXEL_IF0		5
+#define JH7110_ISPRST_VIN_PIXEL_IF1		6
+#define JH7110_ISPRST_VIN_PIXEL_IF2		7
+#define JH7110_ISPRST_VIN_PIXEL_IF3		8
+#define JH7110_ISPRST_VIN_SYS			9
+#define JH7110_ISPRST_VIN_P_AXI_RD		10
+#define JH7110_ISPRST_VIN_P_AXI_WR		11
+
+#define JH7110_ISPRST_END			12
+
+/* VOUTCRG resets */
+#define JH7110_VOUTRST_DC8200_AXI		0
+#define JH7110_VOUTRST_DC8200_AHB		1
+#define JH7110_VOUTRST_DC8200_CORE		2
+#define JH7110_VOUTRST_DSITX_DPI		3
+#define JH7110_VOUTRST_DSITX_APB		4
+#define JH7110_VOUTRST_DSITX_RXESC		5
+#define JH7110_VOUTRST_DSITX_SYS		6
+#define JH7110_VOUTRST_DSITX_TXBYTEHS		7
+#define JH7110_VOUTRST_DSITX_TXESC		8
+#define JH7110_VOUTRST_HDMI_TX_HDMI		9
+#define JH7110_VOUTRST_MIPITX_DPHY_SYS		10
+#define JH7110_VOUTRST_MIPITX_DPHY_TXBYTEHS	11
+
+#define JH7110_VOUTRST_END			12
+
 #endif /* __DT_BINDINGS_RESET_STARFIVE_JH7110_CRG_H__ */