Merge tag 'qcom-arm64-for-4.9' of...

Merge tag 'qcom-arm64-for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt64

Pull "Qualcomm ARM64 Updates for v4.9" from Andy Gross:

* Updates for MSM8916 including TSCR, SMSM/SMP2P, and MBA reserve
* Update SCM node to denote being a reset-controller
* Fix broken interrupt settings
* Add TSENS nodes for MSM8916/MSM8996
* Add DB820c support
* Add MSM8916/APQ8016 display support

* tag 'qcom-arm64-for-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  arm64: dts: apq8016-sbc: Add HDMI display support
  arm64: dts: msm8916: Add display support
  arm64: dts: db820c: add support to external sd card.
  arm64: dts: db820c: add support to SPI on HS
  arm64: dts: db820c: add support to LS-SPI0
  arm64: dts: db820c: add support to I2C on HS
  arm64: dts: db820c: add support to LS-I2C1
  arm64: dts: db820c: add support to LS-I2C0
  arm64: dts: db820c: add support to LS-UART0
  arm64: dts: db820c: add basic board support
  arm64: dts: msm8996: Add thermal zones, tsens and qfprom nodes
  arm64: dts: msm8916: Add thermal zones, tsens and qfprom nodes
  arm64: dts: qcom: Fix broken interrupt trigger settings
  arm64: dts: qcom: msm8916: Add tcsr syscon
  arm64: dts: qcom: msm8916: Make scm a reset-controller
  arm64: dts: qcom: msm8916: Add mba memory reserve
  arm64: dts: qcom: msm8916: Add smsm and smp2p nodes

arch/arm64/boot/dts/qcom/Makefile

 dtb-$(CONFIG_ARCH_QCOM)	+= apq8016-sbc.dtb msm8916-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8996-mtp.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= apq8096-db820c.dtb
 
 always		:= $(dtb-y)
 subdir-y	:= $(dts-dirs)

arch/arm64/boot/dts/qcom/apq8016-sbc-soc-pins.dtsi

@@ -24,4 +24,52 @@ pinconf {
 			bias-pull-up;
 		};
 	};
+
+	adv7533_int_active: adv533_int_active {
+		pinmux {
+			function = "gpio";
+			pins = "gpio31";
+		};
+		pinconf {
+			pins = "gpio31";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	adv7533_int_suspend: adv7533_int_suspend {
+		pinmux {
+			function = "gpio";
+			pins = "gpio31";
+		};
+		pinconf {
+			pins = "gpio31";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
+
+	adv7533_switch_active: adv7533_switch_active {
+		pinmux {
+			function = "gpio";
+			pins = "gpio32";
+		};
+		pinconf {
+			pins = "gpio32";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	adv7533_switch_suspend: adv7533_switch_suspend {
+		pinmux {
+			function = "gpio";
+			pins = "gpio32";
+		};
+		pinconf {
+			pins = "gpio32";
+			drive-strength = <2>;
+			bias-disable;
+		};
+	};
 };

arch/arm64/boot/dts/qcom/apq8016-sbc.dtsi

@@ -63,6 +63,47 @@ i2c@78b8000 {
 		/* On High speed expansion */
 			label = "HS-I2C2";
 			status = "okay";
+
+			adv_bridge: bridge@39 {
+				status = "okay";
+
+				compatible = "adi,adv7533";
+				reg = <0x39>;
+
+				interrupt-parent = <&msmgpio>;
+				interrupts = <31 2>;
+
+				adi,dsi-lanes = <4>;
+
+				pd-gpios = <&msmgpio 32 0>;
+
+				avdd-supply = <&pm8916_l6>;
+				v1p2-supply = <&pm8916_l6>;
+				v3p3-supply = <&pm8916_l17>;
+
+				pinctrl-names = "default","sleep";
+				pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
+				pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						adv7533_in: endpoint {
+							remote-endpoint = <&dsi0_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						adv7533_out: endpoint {
+							remote-endpoint = <&hdmi_con>;
+						};
+					};
+				};
+			};
 		};
 
 		i2c@78ba000 {
@@ -180,6 +221,36 @@ phy@78d9000 {
 		lpass@07708000 {
 			status = "okay";
 		};
+
+		mdss@1a00000 {
+			status = "okay";
+
+			mdp@1a01000 {
+				status = "okay";
+			};
+
+			dsi@1a98000 {
+				status = "okay";
+
+				vdda-supply = <&pm8916_l2>;
+				vddio-supply = <&pm8916_l6>;
+
+				ports {
+					port@1 {
+						endpoint {
+							remote-endpoint = <&adv7533_in>;
+							data-lanes = <0 1 2 3>;
+						};
+					};
+				};
+			};
+
+			dsi-phy@1a98300 {
+				status = "okay";
+
+				vddio-supply = <&pm8916_l6>;
+			};
+		};
 	};
 
 	usb2513 {
@@ -194,6 +265,17 @@ usb_id: usb-id {
 		pinctrl-names = "default";
 		pinctrl-0 = <&usb_id_default>;
 	};
+
+	hdmi-out {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&adv7533_out>;
+			};
+		};
+	};
 };
 
 &smd_rpm_regulators {

arch/arm64/boot/dts/qcom/apq8096-db820c-pins.dtsi

+/*
+ * Copyright (c) 2013-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+&msmgpio {
+	sdc2_cd_on: sdc2_cd_on {
+		mux {
+			pins = "gpio38";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio38";
+			bias-pull-up;		/* pull up */
+			drive-strength = <16>;	/* 16 MA */
+		};
+	};
+
+	sdc2_cd_off: sdc2_cd_off {
+		mux {
+			pins = "gpio38";
+			function = "gpio";
+		};
+
+		config {
+			pins = "gpio38";
+			bias-pull-up;		/* pull up */
+			drive-strength = <2>;	/* 2 MA */
+		};
+	};
+};

arch/arm64/boot/dts/qcom/apq8096-db820c.dts

+/*
+ * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+/dts-v1/;
+
+#include "apq8096-db820c.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. DB820c";
+	compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc";
+};

arch/arm64/boot/dts/qcom/apq8096-db820c.dtsi

+/*
+ * Copyright (c) 2014-2016, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include "msm8996.dtsi"
+#include "apq8096-db820c-pins.dtsi"
+
+/ {
+	aliases {
+		serial0 = &blsp2_uart1;
+		serial1 = &blsp2_uart2;
+		i2c0	= &blsp1_i2c2;
+		i2c1	= &blsp2_i2c1;
+		i2c2	= &blsp2_i2c0;
+		spi0	= &blsp1_spi0;
+		spi1	= &blsp2_spi5;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	soc {
+		serial@75b0000 {
+			label = "LS-UART1";
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_uart1_2pins_default>;
+			pinctrl-1 = <&blsp2_uart1_2pins_sleep>;
+		};
+
+		serial@75b1000 {
+			label = "LS-UART0";
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&blsp2_uart2_4pins_default>;
+			pinctrl-1 = <&blsp2_uart2_4pins_sleep>;
+		};
+
+		i2c@07577000 {
+		/* On Low speed expansion */
+			label = "LS-I2C0";
+			status = "okay";
+		};
+
+		i2c@075b6000 {
+		/* On Low speed expansion */
+			label = "LS-I2C1";
+			status = "okay";
+		};
+
+		spi@07575000 {
+		/* On Low speed expansion */
+			label = "LS-SPI0";
+			status = "okay";
+		};
+
+		i2c@075b5000 {
+		/* On High speed expansion */
+			label = "HS-I2C2";
+			status = "okay";
+		};
+
+		spi@075ba000{
+		/* On High speed expansion */
+			label = "HS-SPI1";
+			status = "okay";
+		};
+
+		sdhci@74a4900 {
+		/* External SD card */
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
+			pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
+			cd-gpios = <&msmgpio 38 0x1>;
+			status = "okay";
+		};
+	};
+};

arch/arm64/boot/dts/qcom/msm8916.dtsi

@@ -86,6 +86,11 @@ wcnss@89300000 {
 			reg = <0x0 0x89300000 0x0 0x600000>;
 			no-map;
 		};
+
+		mba_mem: mba@8ea00000 {
+			no-map;
+			reg = <0 0x8ea00000 0 0x100000>;
+		};
 	};
 
 	cpus {
@@ -155,6 +160,49 @@ pmu {
 		interrupts = <GIC_PPI 7 GIC_CPU_MASK_SIMPLE(4)>;
 	};
 
+	thermal-zones {
+		cpu-thermal0 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 4>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit0: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu-thermal1 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens 3>;
+
+			trips {
+				cpu_alert1: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+				cpu_crit1: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
@@ -187,10 +235,11 @@ smem {
 	};
 
 	firmware {
-		scm {
+		scm: scm {
 			compatible = "qcom,scm";
 			clocks = <&gcc GCC_CRYPTO_CLK>, <&gcc GCC_CRYPTO_AXI_CLK>, <&gcc GCC_CRYPTO_AHB_CLK>;
 			clock-names = "core", "bus", "iface";
+			#reset-cells = <1>;
 		};
 	};
 
@@ -228,6 +277,11 @@ tcsr_mutex_regs: syscon@1905000 {
 			reg = <0x1905000 0x20000>;
 		};
 
+		tcsr: syscon@1937000 {
+			compatible = "qcom,tcsr-msm8916", "syscon";
+			reg = <0x1937000 0x30000>;
+		};
+
 		tcsr_mutex: hwlock {
 			compatible = "qcom,tcsr-mutex";
 			syscon = <&tcsr_mutex_regs 0 0x1000>;
@@ -483,7 +537,7 @@ usb_dev: usb@78d9000 {
 			compatible = "qcom,ci-hdrc";
 			reg = <0x78d9000 0x400>;
 			dr_mode = "peripheral";
-			interrupts = <GIC_SPI 134 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
 			usb-phy = <&usb_otg>;
 			status = "disabled";
 		};
@@ -491,7 +545,7 @@ usb_dev: usb@78d9000 {
 		usb_host: ehci@78d9000 {
 			compatible = "qcom,ehci-host";
 			reg = <0x78d9000 0x400>;
-			interrupts = <GIC_SPI 134 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
 			usb-phy = <&usb_otg>;
 			status = "disabled";
 		};
@@ -499,8 +553,8 @@ usb_host: ehci@78d9000 {
 		usb_otg: phy@78d9000 {
 			compatible = "qcom,usb-otg-snps";
 			reg = <0x78d9000 0x400>;
-			interrupts = <GIC_SPI 134 IRQ_TYPE_EDGE_BOTH>,
-				     <GIC_SPI 140 IRQ_TYPE_EDGE_RISING>;
+			interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
 
 			qcom,vdd-levels = <500000 1000000 1320000>;
 			qcom,phy-init-sequence = <0x44 0x6B 0x24 0x13>;
@@ -594,7 +648,7 @@ spmi_bus: spmi@200f000 {
 			      <0x200a000 0x002100>;
 			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
 			interrupt-names = "periph_irq";
-			interrupts = <GIC_SPI 190 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>;
 			qcom,ee = <0>;
 			qcom,channel = <0>;
 			#address-cells = <2>;
@@ -609,6 +663,144 @@ rng@22000 {
 			clocks = <&gcc GCC_PRNG_AHB_CLK>;
 			clock-names = "core";
 		};
+
+		qfprom: qfprom@5c000 {
+			compatible = "qcom,qfprom";
+			reg = <0x5c000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			tsens_caldata: caldata@d0 {
+				reg = <0xd0 0x8>;
+			};
+			tsens_calsel: calsel@ec {
+				reg = <0xec 0x4>;
+			};
+		};
+
+		tsens: thermal-sensor@4a8000 {
+			compatible = "qcom,msm8916-tsens";
+			reg = <0x4a8000 0x2000>;
+			nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
+			nvmem-cell-names = "calib", "calib_sel";
+			#thermal-sensor-cells = <1>;
+		};
+
+		mdss: mdss@1a00000 {
+			compatible = "qcom,mdss";
+			reg = <0x1a00000 0x1000>,
+			      <0x1ac8000 0x3000>;
+			reg-names = "mdss_phys", "vbif_phys";
+
+			power-domains = <&gcc MDSS_GDSC>;
+
+			clocks = <&gcc GCC_MDSS_AHB_CLK>,
+				 <&gcc GCC_MDSS_AXI_CLK>,
+				 <&gcc GCC_MDSS_VSYNC_CLK>;
+			clock-names = "iface_clk",
+				      "bus_clk",
+				      "vsync_clk";
+
+			interrupts = <0 72 0>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			mdp: mdp@1a01000 {
+				compatible = "qcom,mdp5";
+				reg = <0x1a01000 0x90000>;
+				reg-names = "mdp_phys";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0 0>;
+
+				clocks = <&gcc GCC_MDSS_AHB_CLK>,
+					 <&gcc GCC_MDSS_AXI_CLK>,
+					 <&gcc GCC_MDSS_MDP_CLK>,
+					 <&gcc GCC_MDSS_VSYNC_CLK>;
+				clock-names = "iface_clk",
+					      "bus_clk",
+					      "core_clk",
+					      "vsync_clk";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdp5_intf1_out: endpoint {
+							remote-endpoint = <&dsi0_in>;
+						};
+					};
+				};
+			};
+
+			dsi0: dsi@1a98000 {
+				compatible = "qcom,mdss-dsi-ctrl";
+				reg = <0x1a98000 0x25c>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4 0>;
+
+				assigned-clocks = <&gcc BYTE0_CLK_SRC>,
+						  <&gcc PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&dsi_phy0 0>,
+							 <&dsi_phy0 1>;
+
+				clocks = <&gcc GCC_MDSS_MDP_CLK>,
+					 <&gcc GCC_MDSS_AHB_CLK>,
+					 <&gcc GCC_MDSS_AXI_CLK>,
+					 <&gcc GCC_MDSS_BYTE0_CLK>,
+					 <&gcc GCC_MDSS_PCLK0_CLK>,
+					 <&gcc GCC_MDSS_ESC0_CLK>;
+				clock-names = "mdp_core_clk",
+					      "iface_clk",
+					      "bus_clk",
+					      "byte_clk",
+					      "pixel_clk",
+					      "core_clk";
+				phys = <&dsi_phy0>;
+				phy-names = "dsi-phy";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi0_in: endpoint {
+							remote-endpoint = <&mdp5_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi0_out: endpoint {
+						};
+					};
+				};
+			};
+
+			dsi_phy0: dsi-phy@1a98300 {
+				compatible = "qcom,dsi-phy-28nm-lp";
+				reg = <0x1a98300 0xd4>,
+				      <0x1a98500 0x280>,
+				      <0x1a98780 0x30>;
+				reg-names = "dsi_pll",
+					    "dsi_phy",
+					    "dsi_phy_regulator";
+
+				#clock-cells = <1>;
+
+				clocks = <&gcc GCC_MDSS_AHB_CLK>;
+				clock-names = "iface_clk";
+			};
+		};
 	};
 
 	smd {
@@ -657,6 +849,88 @@ smd_rpm_regulators: pm8916-regulators {
 			};
 		};
 	};
+
+	hexagon-smp2p {
+		compatible = "qcom,smp2p";
+		qcom,smem = <435>, <428>;
+
+		interrupts = <0 27 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 14>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <1>;
+
+		hexagon_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		hexagon_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	wcnss-smp2p {
+		compatible = "qcom,smp2p";
+		qcom,smem = <451>, <431>;
+
+		interrupts = <0 143 IRQ_TYPE_EDGE_RISING>;
+
+		qcom,ipc = <&apcs 8 18>;
+
+		qcom,local-pid = <0>;
+		qcom,remote-pid = <4>;
+
+		wcnss_smp2p_out: master-kernel {
+			qcom,entry-name = "master-kernel";
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		wcnss_smp2p_in: slave-kernel {
+			qcom,entry-name = "slave-kernel";
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	smsm {
+		compatible = "qcom,smsm";
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		qcom,ipc-1 = <&apcs 0 13>;
+		qcom,ipc-6 = <&apcs 0 19>;
+
+		apps_smsm: apps@0 {
+			reg = <0>;
+
+			#qcom,smem-state-cells = <1>;
+		};
+
+		hexagon_smsm: hexagon@1 {
+			reg = <1>;
+			interrupts = <0 26 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		wcnss_smsm: wcnss@6 {
+			reg = <6>;
+			interrupts = <0 144 IRQ_TYPE_EDGE_RISING>;
+
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
 };
 
 #include "msm8916-pins.dtsi"

arch/arm64/boot/dts/qcom/msm8996.dtsi

@@ -97,6 +97,92 @@ core1 {
 		};
 	};
 
+	thermal-zones {
+		cpu-thermal0 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 3>;
+
+			trips {
+				cpu_alert0: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit0: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu-thermal1 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 5>;
+
+			trips {
+				cpu_alert1: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit1: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu-thermal2 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 8>;
+
+			trips {
+				cpu_alert2: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit2: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+
+		cpu-thermal3 {
+			polling-delay-passive = <250>;
+			polling-delay = <1000>;
+
+			thermal-sensors = <&tsens0 10>;
+
+			trips {
+				cpu_alert3: trip0 {
+					temperature = <75000>;
+					hysteresis = <2000>;
+					type = "passive";
+				};
+
+				cpu_crit3: trip1 {
+					temperature = <110000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
@@ -181,6 +267,12 @@ blsp2_i2c0: i2c@075b5000 {
 			status = "disabled";
 		};
 
+		tsens0: thermal-sensor@4a8000 {
+			compatible = "qcom,msm8996-tsens";
+			reg = <0x4a8000 0x2000>;
+			#thermal-sensor-cells = <1>;
+		};
+
 		blsp2_uart1: serial@75b0000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0x75b0000 0x1000>;
@@ -339,7 +431,7 @@ spmi_bus: qcom,spmi@400f000 {
 			      <0x400a000 0x002100>;
 			reg-names = "core", "chnls", "obsrvr", "intr", "cnfg";
 			interrupt-names = "periph_irq";
-			interrupts = <GIC_SPI 326 IRQ_TYPE_NONE>;
+			interrupts = <GIC_SPI 326 IRQ_TYPE_LEVEL_HIGH>;
 			qcom,ee = <0>;
 			qcom,channel = <0>;
 			#address-cells = <2>;