arm64: dts: qcom: sa8775p: add UFS nodes

Add nodes for the UFS and its PHY on sa8775p platforms.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230411130446.401440-5-brgl@bgdev.pl

arch/arm64/boot/dts/qcom/sa8775p.dtsi

@@ -590,6 +590,64 @@ &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
 			};
 		};
 
+		ufs_mem_hc: ufs@1d84000 {
+			compatible = "qcom,sa8775p-ufshc", "qcom,ufshc", "jedec,ufs-2.0";
+			reg = <0x0 0x01d84000 0x0 0x3000>;
+			interrupts = <GIC_SPI 265 IRQ_TYPE_LEVEL_HIGH>;
+			phys = <&ufs_mem_phy>;
+			phy-names = "ufsphy";
+			lanes-per-direction = <2>;
+			#reset-cells = <1>;
+			resets = <&gcc GCC_UFS_PHY_BCR>;
+			reset-names = "rst";
+			power-domains = <&gcc UFS_PHY_GDSC>;
+			required-opps = <&rpmhpd_opp_nom>;
+			iommus = <&apps_smmu 0x100 0x0>;
+			clocks = <&gcc GCC_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_AGGRE_UFS_PHY_AXI_CLK>,
+				 <&gcc GCC_UFS_PHY_AHB_CLK>,
+				 <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>,
+				 <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>,
+				 <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>,
+				 <&gcc GCC_UFS_PHY_RX_SYMBOL_1_CLK>;
+			clock-names = "core_clk",
+				      "bus_aggr_clk",
+				      "iface_clk",
+				      "core_clk_unipro",
+				      "ref_clk",
+				      "tx_lane0_sync_clk",
+				      "rx_lane0_sync_clk",
+				      "rx_lane1_sync_clk";
+			freq-table-hz = <75000000 300000000>,
+					<0 0>,
+					<0 0>,
+					<75000000 300000000>,
+					<0 0>,
+					<0 0>,
+					<0 0>,
+					<0 0>;
+			status = "disabled";
+		};
+
+		ufs_mem_phy: phy@1d87000 {
+			compatible = "qcom,sa8775p-qmp-ufs-phy";
+			reg = <0x0 0x01d87000 0x0 0xe10>;
+			/*
+			 * Yes, GCC_EDP_REF_CLKREF_EN is correct in qref. It
+			 * enables the CXO clock to eDP *and* UFS PHY.
+			 */
+			clocks = <&rpmhcc RPMH_CXO_CLK>,
+				 <&gcc GCC_UFS_PHY_PHY_AUX_CLK>,
+				 <&gcc GCC_EDP_REF_CLKREF_EN>;
+			clock-names = "ref", "ref_aux", "qref";
+			power-domains = <&gcc UFS_PHY_GDSC>;
+			resets = <&ufs_mem_hc 0>;
+			reset-names = "ufsphy";
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
 		tcsr_mutex: hwlock@1f40000 {
 			compatible = "qcom,tcsr-mutex";
 			reg = <0x0 0x01f40000 0x0 0x20000>;