fbdev: mx3fb: Remove the driver

The mx3fb driver does not support devicetree and i.MX has been converted
to a DT-only platform since kernel 5.10.

As there is no user for this driver anymore, just remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Helge Deller <deller@gmx.de>

drivers/video/fbdev/Kconfig

@@ -1887,17 +1887,6 @@ config FB_PRE_INIT_FB
 	  Select this option if display contents should be inherited as set by
 	  the bootloader.
 
-config FB_MX3
-	tristate "MX3 Framebuffer support"
-	depends on FB && MX3_IPU
-	select BACKLIGHT_CLASS_DEVICE
-	select FB_IOMEM_HELPERS
-	default y
-	help
-	  This is a framebuffer device for the i.MX31 LCD Controller. So
-	  far only synchronous displays are supported. If you plan to use
-	  an LCD display with your i.MX31 system, say Y here.
-
 config FB_BROADSHEET
 	tristate "E-Ink Broadsheet/Epson S1D13521 controller support"
 	depends on FB && (ARCH_PXA || COMPILE_TEST)

drivers/video/fbdev/Makefile

@@ -122,7 +122,6 @@ obj-$(CONFIG_FB_VESA)             += vesafb.o
 obj-$(CONFIG_FB_EFI)              += efifb.o
 obj-$(CONFIG_FB_VGA16)            += vga16fb.o
 obj-$(CONFIG_FB_OF)               += offb.o
-obj-$(CONFIG_FB_MX3)		  += mx3fb.o
 obj-$(CONFIG_FB_DA8XX)		  += da8xx-fb.o
 obj-$(CONFIG_FB_SSD1307)	  += ssd1307fb.o
 obj-$(CONFIG_FB_SIMPLE)           += simplefb.o

include/linux/platform_data/video-mx3fb.h

-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) 2008
- * Guennadi Liakhovetski, DENX Software Engineering, <lg@denx.de>
- */
-
-#ifndef __ASM_ARCH_MX3FB_H__
-#define __ASM_ARCH_MX3FB_H__
-
-#include <linux/device.h>
-#include <linux/fb.h>
-
-/* Proprietary FB_SYNC_ flags */
-#define FB_SYNC_OE_ACT_HIGH	0x80000000
-#define FB_SYNC_CLK_INVERT	0x40000000
-#define FB_SYNC_DATA_INVERT	0x20000000
-#define FB_SYNC_CLK_IDLE_EN	0x10000000
-#define FB_SYNC_SHARP_MODE	0x08000000
-#define FB_SYNC_SWAP_RGB	0x04000000
-#define FB_SYNC_CLK_SEL_EN	0x02000000
-
-/*
- * Specify the way your display is connected. The IPU can arbitrarily
- * map the internal colors to the external data lines. We only support
- * the following mappings at the moment.
- */
-enum disp_data_mapping {
-	/* blue -> d[0..5], green -> d[6..11], red -> d[12..17] */
-	IPU_DISP_DATA_MAPPING_RGB666,
-	/* blue -> d[0..4], green -> d[5..10], red -> d[11..15] */
-	IPU_DISP_DATA_MAPPING_RGB565,
-	/* blue -> d[0..7], green -> d[8..15], red -> d[16..23] */
-	IPU_DISP_DATA_MAPPING_RGB888,
-};
-
-/**
- * struct mx3fb_platform_data - mx3fb platform data
- *
- * @dma_dev:	pointer to the dma-device, used for dma-slave connection
- * @mode:	pointer to a platform-provided per mxc_register_fb() videomode
- */
-struct mx3fb_platform_data {
-	struct device			*dma_dev;
-	const char			*name;
-	const struct fb_videomode	*mode;
-	int				num_modes;
-	enum disp_data_mapping		disp_data_fmt;
-};
-
-#endif