drm/kmb: Enable alpha blended second plane

Enable one additional plane that is alpha blended on top
of the primary plane.

This also fixes the below warnings when building with
-Warray-bounds:

drivers/gpu/drm/kmb/kmb_plane.c:135:20: warning: array subscript 3 is
above array bounds of 'struct layer_status[1]' [-Warray-bounds]
drivers/gpu/drm/kmb/kmb_plane.c:132:20: warning: array subscript 2 is
above array bounds of 'struct layer_status[1]' [-Warray-bounds]
drivers/gpu/drm/kmb/kmb_plane.c:129:20: warning: array subscript 1 is
above array bounds of 'struct layer_status[1]' [-Warray-bounds]

v2: corrected previous patch dependecies so it builds
Signed-off-by: Edmund Dea <edmund.j.dea@intel.com>
Signed-off-by: Anitha Chrisanthus <anitha.chrisanthus@intel.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20210728003126.1425028-13-anitha.chrisanthus@intel.com/Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drivers/gpu/drm/kmb/kmb_drv.c

@@ -172,10 +172,10 @@ static int kmb_setup_mode_config(struct drm_device *drm)
 	ret = drmm_mode_config_init(drm);
 	if (ret)
 		return ret;
-	drm->mode_config.min_width = KMB_MIN_WIDTH;
-	drm->mode_config.min_height = KMB_MIN_HEIGHT;
-	drm->mode_config.max_width = KMB_MAX_WIDTH;
-	drm->mode_config.max_height = KMB_MAX_HEIGHT;
+	drm->mode_config.min_width = KMB_FB_MIN_WIDTH;
+	drm->mode_config.min_height = KMB_FB_MIN_HEIGHT;
+	drm->mode_config.max_width = KMB_FB_MAX_WIDTH;
+	drm->mode_config.max_height = KMB_FB_MAX_HEIGHT;
 	drm->mode_config.funcs = &kmb_mode_config_funcs;
 
 	ret = kmb_setup_crtc(drm);

drivers/gpu/drm/kmb/kmb_drv.h

@@ -20,6 +20,11 @@
 #define DRIVER_MAJOR			1
 #define DRIVER_MINOR			1
 
+#define KMB_FB_MAX_WIDTH		1920
+#define KMB_FB_MAX_HEIGHT		1080
+#define KMB_FB_MIN_WIDTH		1
+#define KMB_FB_MIN_HEIGHT		1
+
 #define KMB_LCD_DEFAULT_CLK		200000000
 #define KMB_SYS_CLK_MHZ			500
 

drivers/gpu/drm/kmb/kmb_plane.c

@@ -94,9 +94,10 @@ static int kmb_plane_atomic_check(struct drm_plane *plane,
 	if (ret)
 		return ret;
 
-	if (new_plane_state->crtc_w > KMB_MAX_WIDTH || new_plane_state->crtc_h > KMB_MAX_HEIGHT)
-		return -EINVAL;
-	if (new_plane_state->crtc_w < KMB_MIN_WIDTH || new_plane_state->crtc_h < KMB_MIN_HEIGHT)
+	if (new_plane_state->crtc_w > KMB_FB_MAX_WIDTH ||
+	    new_plane_state->crtc_h > KMB_FB_MAX_HEIGHT ||
+	    new_plane_state->crtc_w < KMB_FB_MIN_WIDTH ||
+	    new_plane_state->crtc_h < KMB_FB_MIN_HEIGHT)
 		return -EINVAL;
 	can_position = (plane->type == DRM_PLANE_TYPE_OVERLAY);
 	crtc_state =
@@ -277,6 +278,44 @@ static void config_csc(struct kmb_drm_private *kmb, int plane_id)
 	kmb_write_lcd(kmb, LCD_LAYERn_CSC_OFF3(plane_id), csc_coef_lcd[11]);
 }
 
+static void kmb_plane_set_alpha(struct kmb_drm_private *kmb,
+				const struct drm_plane_state *state,
+				unsigned char plane_id,
+				unsigned int *val)
+{
+	u16 plane_alpha = state->alpha;
+	u16 pixel_blend_mode = state->pixel_blend_mode;
+	int has_alpha = state->fb->format->has_alpha;
+
+	if (plane_alpha != DRM_BLEND_ALPHA_OPAQUE)
+		*val |= LCD_LAYER_ALPHA_STATIC;
+
+	if (has_alpha) {
+		switch (pixel_blend_mode) {
+		case DRM_MODE_BLEND_PIXEL_NONE:
+			break;
+		case DRM_MODE_BLEND_PREMULTI:
+			*val |= LCD_LAYER_ALPHA_EMBED | LCD_LAYER_ALPHA_PREMULT;
+			break;
+		case DRM_MODE_BLEND_COVERAGE:
+			*val |= LCD_LAYER_ALPHA_EMBED;
+			break;
+		default:
+			DRM_DEBUG("Missing pixel blend mode case (%s == %ld)\n",
+				  __stringify(pixel_blend_mode),
+				  (long)pixel_blend_mode);
+			break;
+		}
+	}
+
+	if (plane_alpha == DRM_BLEND_ALPHA_OPAQUE && !has_alpha) {
+		*val &= LCD_LAYER_ALPHA_DISABLED;
+		return;
+	}
+
+	kmb_write_lcd(kmb, LCD_LAYERn_ALPHA(plane_id), plane_alpha);
+}
+
 static void kmb_plane_atomic_update(struct drm_plane *plane,
 				    struct drm_atomic_state *state)
 {
@@ -303,11 +342,12 @@ static void kmb_plane_atomic_update(struct drm_plane *plane,
 	fb = new_plane_state->fb;
 	if (!fb)
 		return;
+
 	num_planes = fb->format->num_planes;
 	kmb_plane = to_kmb_plane(plane);
-	plane_id = kmb_plane->id;
 
 	kmb = to_kmb(plane->dev);
+	plane_id = kmb_plane->id;
 
 	spin_lock_irq(&kmb->irq_lock);
 	if (kmb->kmb_under_flow || kmb->kmb_flush_done) {
@@ -400,20 +440,32 @@ static void kmb_plane_atomic_update(struct drm_plane *plane,
 		config_csc(kmb, plane_id);
 	}
 
+	kmb_plane_set_alpha(kmb, plane->state, plane_id, &val);
+
 	kmb_write_lcd(kmb, LCD_LAYERn_CFG(plane_id), val);
 
+	/* Configure LCD_CONTROL */
+	ctrl = kmb_read_lcd(kmb, LCD_CONTROL);
+
+	/* Set layer blending config */
+	ctrl &= ~LCD_CTRL_ALPHA_ALL;
+	ctrl |= LCD_CTRL_ALPHA_BOTTOM_VL1 |
+		LCD_CTRL_ALPHA_BLEND_VL2;
+
+	ctrl &= ~LCD_CTRL_ALPHA_BLEND_BKGND_DISABLE;
+
 	switch (plane_id) {
 	case LAYER_0:
-		ctrl = LCD_CTRL_VL1_ENABLE;
+		ctrl |= LCD_CTRL_VL1_ENABLE;
 		break;
 	case LAYER_1:
-		ctrl = LCD_CTRL_VL2_ENABLE;
+		ctrl |= LCD_CTRL_VL2_ENABLE;
 		break;
 	case LAYER_2:
-		ctrl = LCD_CTRL_GL1_ENABLE;
+		ctrl |= LCD_CTRL_GL1_ENABLE;
 		break;
 	case LAYER_3:
-		ctrl = LCD_CTRL_GL2_ENABLE;
+		ctrl |= LCD_CTRL_GL2_ENABLE;
 		break;
 	}
 
@@ -425,7 +477,7 @@ static void kmb_plane_atomic_update(struct drm_plane *plane,
 	 */
 	ctrl |= LCD_CTRL_VHSYNC_IDLE_LVL;
 
-	kmb_set_bitmask_lcd(kmb, LCD_CONTROL, ctrl);
+	kmb_write_lcd(kmb, LCD_CONTROL, ctrl);
 
 	/* Enable pipeline AXI read transactions for the DMA
 	 * after setting graphics layers. This must be done
@@ -490,6 +542,9 @@ struct kmb_plane *kmb_plane_init(struct drm_device *drm)
 	enum drm_plane_type plane_type;
 	const u32 *plane_formats;
 	int num_plane_formats;
+	unsigned int blend_caps = BIT(DRM_MODE_BLEND_PIXEL_NONE) |
+				  BIT(DRM_MODE_BLEND_PREMULTI)   |
+				  BIT(DRM_MODE_BLEND_COVERAGE);
 
 	for (i = 0; i < KMB_MAX_PLANES; i++) {
 		plane = drmm_kzalloc(drm, sizeof(*plane), GFP_KERNEL);
@@ -521,8 +576,16 @@ struct kmb_plane *kmb_plane_init(struct drm_device *drm)
 		drm_dbg(drm, "%s : %d i=%d type=%d",
 			__func__, __LINE__,
 			  i, plane_type);
+		drm_plane_create_alpha_property(&plane->base_plane);
+
+		drm_plane_create_blend_mode_property(&plane->base_plane,
+						     blend_caps);
+
+		drm_plane_create_zpos_immutable_property(&plane->base_plane, i);
+
 		drm_plane_helper_add(&plane->base_plane,
 				     &kmb_plane_helper_funcs);
+
 		if (plane_type == DRM_PLANE_TYPE_PRIMARY) {
 			primary = plane;
 			kmb->plane = plane;

drivers/gpu/drm/kmb/kmb_plane.h

@@ -35,6 +35,9 @@
 #define POSSIBLE_CRTCS 1
 #define to_kmb_plane(x) container_of(x, struct kmb_plane, base_plane)
 
+#define POSSIBLE_CRTCS		1
+#define KMB_MAX_PLANES		2
+
 enum layer_id {
 	LAYER_0,
 	LAYER_1,
@@ -43,8 +46,6 @@ enum layer_id {
 	/* KMB_MAX_PLANES */
 };
 
-#define KMB_MAX_PLANES 1
-
 enum sub_plane_id {
 	Y_PLANE,
 	U_PLANE,

drivers/gpu/drm/kmb/kmb_regs.h

@@ -43,8 +43,10 @@
 #define LCD_CTRL_OUTPUT_ENABLED			  BIT(19)
 #define LCD_CTRL_BPORCH_ENABLE			  BIT(21)
 #define LCD_CTRL_FPORCH_ENABLE			  BIT(22)
+#define LCD_CTRL_ALPHA_BLEND_BKGND_DISABLE	  BIT(23)
 #define LCD_CTRL_PIPELINE_DMA			  BIT(28)
 #define LCD_CTRL_VHSYNC_IDLE_LVL		  BIT(31)
+#define LCD_CTRL_ALPHA_ALL			  (0xff << 6)
 
 /* interrupts */
 #define LCD_INT_STATUS				(0x4 * 0x001)
@@ -115,6 +117,7 @@
 #define LCD_LAYER_ALPHA_EMBED			BIT(5)
 #define LCD_LAYER_ALPHA_COMBI			(LCD_LAYER_ALPHA_STATIC | \
 						      LCD_LAYER_ALPHA_EMBED)
+#define LCD_LAYER_ALPHA_DISABLED		~(LCD_LAYER_ALPHA_COMBI)
 /* RGB multiplied with alpha */
 #define LCD_LAYER_ALPHA_PREMULT			BIT(6)
 #define LCD_LAYER_INVERT_COL			BIT(7)