Merge branch 'for-6.10/i2c-hid' into for-linus

- PM fixes for STM and Weida Tech devices (Kenny Levinsen)

drivers/hid/i2c-hid/i2c-hid-core.c

@@ -163,6 +163,24 @@ static u32 i2c_hid_lookup_quirk(const u16 idVendor, const u16 idProduct)
 	return quirks;
 }
 
+static int i2c_hid_probe_address(struct i2c_hid *ihid)
+{
+	int ret;
+
+	/*
+	 * Some STM-based devices need 400µs after a rising clock edge to wake
+	 * from deep sleep, in which case the first read will fail. Try after a
+	 * short sleep to see if the device came alive on the bus. Certain
+	 * Weida Tech devices also need this.
+	 */
+	ret = i2c_smbus_read_byte(ihid->client);
+	if (ret < 0) {
+		usleep_range(400, 500);
+		ret = i2c_smbus_read_byte(ihid->client);
+	}
+	return ret < 0 ? ret : 0;
+}
+
 static int i2c_hid_xfer(struct i2c_hid *ihid,
 			u8 *send_buf, int send_len, u8 *recv_buf, int recv_len)
 {
@@ -384,26 +402,11 @@ static int i2c_hid_set_power(struct i2c_hid *ihid, int power_state)
 
 	i2c_hid_dbg(ihid, "%s\n", __func__);
 
-	/*
-	 * Some devices require to send a command to wakeup before power on.
-	 * The call will get a return value (EREMOTEIO) but device will be
-	 * triggered and activated. After that, it goes like a normal device.
-	 */
-	if (power_state == I2C_HID_PWR_ON) {
-		ret = i2c_hid_set_power_command(ihid, I2C_HID_PWR_ON);
-
-		/* Device was already activated */
-		if (!ret)
-			goto set_pwr_exit;
-	}
-
 	ret = i2c_hid_set_power_command(ihid, power_state);
 	if (ret)
 		dev_err(&ihid->client->dev,
 			"failed to change power setting.\n");
 
-set_pwr_exit:
-
 	/*
 	 * The HID over I2C specification states that if a DEVICE needs time
 	 * after the PWR_ON request, it should utilise CLOCK stretching.
@@ -959,6 +962,14 @@ static int i2c_hid_core_resume(struct i2c_hid *ihid)
 
 	enable_irq(client->irq);
 
+	/* Make sure the device is awake on the bus */
+	ret = i2c_hid_probe_address(ihid);
+	if (ret < 0) {
+		dev_err(&client->dev, "nothing at address after resume: %d\n",
+			ret);
+		return -ENXIO;
+	}
+
 	/* Instead of resetting device, simply powers the device on. This
 	 * solves "incomplete reports" on Raydium devices 2386:3118 and
 	 * 2386:4B33 and fixes various SIS touchscreens no longer sending
@@ -992,8 +1003,7 @@ static int __i2c_hid_core_probe(struct i2c_hid *ihid)
 	struct hid_device *hid = ihid->hid;
 	int ret;
 
-	/* Make sure there is something at this address */
-	ret = i2c_smbus_read_byte(client);
+	ret = i2c_hid_probe_address(ihid);
 	if (ret < 0) {
 		i2c_hid_dbg(ihid, "nothing at this address: %d\n", ret);
 		return -ENXIO;