Merge tag 'i2c-for-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c fixes from Wolfram Sang:
 "The main thing is the removal of 'probe_new' because all i2c client
  drivers are converted now. Thanks Uwe, this marks the end of a long
  conversion process.

  Other than that, we have a few Kconfig updates and driver bugfixes"

* tag 'i2c-for-6.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: cadence: Fix the kernel-doc warnings
  i2c: aspeed: Reset the i2c controller when timeout occurs
  i2c: I2C_MLXCPLD on ARM64 should depend on ACPI
  i2c: Make I2C_ATR invisible
  i2c: Drop legacy callback .probe_new()
  w1: ds2482: Switch back to use struct i2c_driver's .probe()

drivers/i2c/Kconfig

@@ -72,7 +72,7 @@ config I2C_MUX
 source "drivers/i2c/muxes/Kconfig"
 
 config I2C_ATR
-	tristate "I2C Address Translator (ATR) support"
+	tristate "I2C Address Translator (ATR) support" if COMPILE_TEST
 	help
 	  Enable support for I2C Address Translator (ATR) chips.
 

drivers/i2c/busses/Kconfig

@@ -1384,10 +1384,10 @@ config I2C_ICY
 
 config I2C_MLXCPLD
 	tristate "Mellanox I2C driver"
-	depends on X86_64 || ARM64 || COMPILE_TEST
+	depends on X86_64 || (ARM64 && ACPI) || COMPILE_TEST
 	help
 	  This exposes the Mellanox platform I2C busses to the linux I2C layer
-	  for X86 based systems.
+	  for X86 and ARM64/ACPI based systems.
 	  Controller is implemented as CPLD logic.
 
 	  This driver can also be built as a module. If so, the module will be

drivers/i2c/busses/i2c-aspeed.c

@@ -698,13 +698,16 @@ static int aspeed_i2c_master_xfer(struct i2c_adapter *adap,
 
 	if (time_left == 0) {
 		/*
-		 * If timed out and bus is still busy in a multi master
-		 * environment, attempt recovery at here.
+		 * In a multi-master setup, if a timeout occurs, attempt
+		 * recovery. But if the bus is idle, we still need to reset the
+		 * i2c controller to clear the remaining interrupts.
 		 */
 		if (bus->multi_master &&
 		    (readl(bus->base + ASPEED_I2C_CMD_REG) &
 		     ASPEED_I2CD_BUS_BUSY_STS))
 			aspeed_i2c_recover_bus(bus);
+		else
+			aspeed_i2c_reset(bus);
 
 		/*
 		 * If timed out and the state is still pending, drop the pending

drivers/i2c/busses/i2c-cadence.c

@@ -182,6 +182,7 @@ enum cdns_i2c_slave_state {
  * @reset:		Reset control for the device
  * @quirks:		flag for broken hold bit usage in r1p10
  * @ctrl_reg:		Cached value of the control register.
+ * @rinfo:		I2C GPIO recovery information
  * @ctrl_reg_diva_divb: value of fields DIV_A and DIV_B from CR register
  * @slave:		Registered slave instance.
  * @dev_mode:		I2C operating role(master/slave).

drivers/w1/masters/ds2482.c

@@ -551,7 +551,7 @@ static struct i2c_driver ds2482_driver = {
 	.driver = {
 		.name	= "ds2482",
 	},
-	.probe_new	= ds2482_probe,
+	.probe		= ds2482_probe,
 	.remove		= ds2482_remove,
 	.id_table	= ds2482_id,
 };

include/linux/i2c.h

@@ -237,7 +237,6 @@ enum i2c_driver_flags {
  * struct i2c_driver - represent an I2C device driver
  * @class: What kind of i2c device we instantiate (for detect)
  * @probe: Callback for device binding
- * @probe_new: Transitional callback for device binding - do not use
  * @remove: Callback for device unbinding
  * @shutdown: Callback for device shutdown
  * @alert: Alert callback, for example for the SMBus alert protocol
@@ -272,16 +271,8 @@ enum i2c_driver_flags {
 struct i2c_driver {
 	unsigned int class;
 
-	union {
 	/* Standard driver model interfaces */
-		int (*probe)(struct i2c_client *client);
-		/*
-		 * Legacy callback that was part of a conversion of .probe().
-		 * Today it has the same semantic as .probe(). Don't use for new
-		 * code.
-		 */
-		int (*probe_new)(struct i2c_client *client);
-	};
+	int (*probe)(struct i2c_client *client);
 	void (*remove)(struct i2c_client *client);