serial:st-asc: Add ST ASC driver.

This patch adds support to ASC (asynchronous serial controller)
driver, which is basically a standard serial driver. This IP is common
across all the ST parts for settop box platforms.

ASC is embedded in ST COMMS IP block. It supports Rx & Tx functionality.
It support all industry standard baud rates.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
CC: Stephen Gallimore <stephen.gallimore@st.com>
CC: Stuart Menefy <stuart.menefy@st.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Documentation/devicetree/bindings/tty/serial/st-asc.txt

+*st-asc(Serial Port)
+
+Required properties:
+- compatible : Should be "st,asc".
+- reg, reg-names, interrupts, interrupt-names	: Standard way to define device
+			resources with names. look in
+			Documentation/devicetree/bindings/resource-names.txt
+
+Optional properties:
+- st,hw-flow-ctrl	bool flag to enable hardware flow control.
+- st,force-m1		bool flat to force asc to be in Mode-1 recommeded
+			for high bit rates (above 19.2K)
+Example:
+serial@fe440000{
+    compatible    = "st,asc";
+    reg         = <0xfe440000 0x2c>;
+    interrupts     =  <0 209 0>;
+};

drivers/tty/serial/Kconfig

@@ -1497,6 +1497,22 @@ config SERIAL_FSL_LPUART_CONSOLE
 	  If you have enabled the lpuart serial port on the Freescale SoCs,
 	  you can make it the console by answering Y to this option.
 
+config SERIAL_ST_ASC
+	tristate "ST ASC serial port support"
+	select SERIAL_CORE
+	help
+	  This driver is for the on-chip Asychronous Serial Controller on
+	  STMicroelectronics STi SoCs.
+	  ASC is embedded in ST COMMS IP block. It supports Rx & Tx functionality.
+	  It support all industry standard baud rates.
+
+	  If unsure, say N.
+
+config SERIAL_ST_ASC_CONSOLE
+	bool "Support for console on ST ASC"
+	depends on SERIAL_ST_ASC=y
+	select SERIAL_CORE_CONSOLE
+
 endmenu
 
 endif # TTY

drivers/tty/serial/Makefile

@@ -65,6 +65,7 @@ obj-$(CONFIG_SERIAL_KGDB_NMI) += kgdb_nmi.o
 obj-$(CONFIG_SERIAL_KS8695) += serial_ks8695.o
 obj-$(CONFIG_SERIAL_OMAP) += omap-serial.o
 obj-$(CONFIG_SERIAL_ALTERA_UART) += altera_uart.o
+obj-$(CONFIG_SERIAL_ST_ASC) += st-asc.o
 obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o
 obj-$(CONFIG_SERIAL_QE) += ucc_uart.o
 obj-$(CONFIG_SERIAL_TIMBERDALE)	+= timbuart.o

include/uapi/linux/serial_core.h

@@ -232,4 +232,7 @@
 /* SH-SCI */
 #define PORT_HSCIF	104
 
+/* ST ASC type numbers */
+#define PORT_ASC       105
+
 #endif /* _UAPILINUX_SERIAL_CORE_H */