Commit c557a4b3 authored by Alexander Duyck's avatar Alexander Duyck Committed by Jeff Kirsher

e1000e: Use netdev_info instead of pr_info for link messages

Replace the pr_info calls with netdev_info in all cases related to the
netdevice link state.

As a result of this patch the link messages will change as shown below.
Before:
e1000e: ens3 NIC Link is Down
e1000e: ens3 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx

After:
e1000e 0000:00:03.0 ens3: NIC Link is Down
e1000e 0000:00:03.0 ens3: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
Suggested-by: default avatarJoe Perches <joe@perches.com>
Signed-off-by: default avatarAlexander Duyck <alexander.h.duyck@linux.intel.com>
Acked-by: default avatarNeil Horman <nhorman@tuxdriver.com>
Tested-by: default avatarAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
parent 9513d2a5
......@@ -4723,7 +4723,7 @@ int e1000e_close(struct net_device *netdev)
e1000_free_irq(adapter);
/* Link status message must follow this format */
pr_info("%s NIC Link is Down\n", netdev->name);
netdev_info(netdev, "NIC Link is Down\n");
}
napi_disable(&adapter->napi);
......@@ -5073,12 +5073,13 @@ static void e1000_print_link_info(struct e1000_adapter *adapter)
u32 ctrl = er32(CTRL);
/* Link status message must follow this format for user tools */
pr_info("%s NIC Link is Up %d Mbps %s Duplex, Flow Control: %s\n",
adapter->netdev->name, adapter->link_speed,
adapter->link_duplex == FULL_DUPLEX ? "Full" : "Half",
(ctrl & E1000_CTRL_TFCE) && (ctrl & E1000_CTRL_RFCE) ? "Rx/Tx" :
(ctrl & E1000_CTRL_RFCE) ? "Rx" :
(ctrl & E1000_CTRL_TFCE) ? "Tx" : "None");
netdev_info(adapter->netdev,
"NIC Link is Up %d Mbps %s Duplex, Flow Control: %s\n",
adapter->link_speed,
adapter->link_duplex == FULL_DUPLEX ? "Full" : "Half",
(ctrl & E1000_CTRL_TFCE) && (ctrl & E1000_CTRL_RFCE) ? "Rx/Tx" :
(ctrl & E1000_CTRL_RFCE) ? "Rx" :
(ctrl & E1000_CTRL_TFCE) ? "Tx" : "None");
}
static bool e1000e_has_link(struct e1000_adapter *adapter)
......@@ -5307,7 +5308,7 @@ static void e1000_watchdog_task(struct work_struct *work)
adapter->link_speed = 0;
adapter->link_duplex = 0;
/* Link status message must follow this format */
pr_info("%s NIC Link is Down\n", adapter->netdev->name);
netdev_info(netdev, "NIC Link is Down\n");
netif_carrier_off(netdev);
netif_stop_queue(netdev);
if (!test_bit(__E1000_DOWN, &adapter->state))
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment