Commit c9736600 authored by Abel Vesa's avatar Abel Vesa Committed by Vinod Koul

phy: qcom-qmp: qserdes-txrx-ufs: Add v6 register offsets

The new SM8550 SoC bumps up the HW version of QMP phy to v6 for USB,
UFS and PCIE g3x2. Add the new qserdes TX RX but UFS specific offsets
in a dedicated header file.
Signed-off-by: default avatarAbel Vesa <abel.vesa@linaro.org>
Reviewed-by: default avatarDmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20230117224148.1914627-5-abel.vesa@linaro.orgSigned-off-by: default avatarVinod Koul <vkoul@kernel.org>
parent ddf070f6
/* SPDX-License-Identifier: GPL-2.0 */
/*
* Copyright (c) 2023, Linaro Limited
*/
#ifndef QCOM_PHY_QMP_QSERDES_TXRX_UFS_V6_H_
#define QCOM_PHY_QMP_QSERDES_TXRX_UFS_V6_H_
#define QSERDES_UFS_V6_TX_RES_CODE_LANE_TX 0x28
#define QSERDES_UFS_V6_TX_RES_CODE_LANE_RX 0x2c
#define QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_TX 0x30
#define QSERDES_UFS_V6_TX_RES_CODE_LANE_OFFSET_RX 0x34
#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE2 0x08
#define QSERDES_UFS_V6_RX_UCDR_FASTLOCK_FO_GAIN_RATE4 0x10
#define QSERDES_UFS_V6_RX_VGA_CAL_MAN_VAL 0x178
#define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B0 0x208
#define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B1 0x20c
#define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B3 0x214
#define QSERDES_UFS_V6_RX_MODE_RATE_0_1_B6 0x220
#define QSERDES_UFS_V6_RX_MODE_RATE2_B3 0x238
#define QSERDES_UFS_V6_RX_MODE_RATE2_B6 0x244
#define QSERDES_UFS_V6_RX_MODE_RATE3_B3 0x25c
#define QSERDES_UFS_V6_RX_MODE_RATE3_B4 0x260
#define QSERDES_UFS_V6_RX_MODE_RATE3_B5 0x264
#define QSERDES_UFS_V6_RX_MODE_RATE3_B8 0x270
#define QSERDES_UFS_V6_RX_MODE_RATE4_B3 0x280
#define QSERDES_UFS_V6_RX_MODE_RATE4_B6 0x28c
#endif
......@@ -27,6 +27,8 @@
#include "phy-qcom-qmp-pcs-ufs-v4.h"
#include "phy-qcom-qmp-pcs-ufs-v5.h"
#include "phy-qcom-qmp-qserdes-txrx-ufs-v6.h"
/* QPHY_SW_RESET bit */
#define SW_RESET BIT(0)
/* QPHY_POWER_DOWN_CONTROL */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment