[ARM] pxa: correct SSCR0_SCR to support multiple SoCs

The previous definitions of SSCR0_SCR and SSCR0_SerClkDiv() prevented
them being used simultaneously when supporting multiple PXA SoCs, esp.
in drivers/spi/pxa2xx_spi.c, make them correct.

The change from SSCR0_SerClkDiv(2) to SSCR0_SCR(2), will make the result
a little bit different in pxa2xx_spi_probe(), however, since that's only
used as a default initialization value, it's acceptable.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

arch/arm/mach-pxa/include/mach/regs-ssp.h

@@ -33,14 +33,7 @@
 #define SSCR0_National	(0x2 << 4)	/* National Microwire */
 #define SSCR0_ECS	(1 << 6)	/* External clock select */
 #define SSCR0_SSE	(1 << 7)	/* Synchronous Serial Port Enable */
-
-#if defined(CONFIG_PXA25x)
-#define SSCR0_SCR	(0x0000ff00)	/* Serial Clock Rate (mask) */
-#define SSCR0_SerClkDiv(x) ((((x) - 2)/2) << 8) /* Divisor [2..512] */
-#elif defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
-#define SSCR0_SCR	(0x000fff00)	/* Serial Clock Rate (mask) */
-#define SSCR0_SerClkDiv(x) (((x) - 1) << 8) /* Divisor [1..4096] */
-#endif
+#define SSCR0_SCR(x)	((x) << 8)	/* Serial Clock Rate (mask) */
 
 #if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx)
 #define SSCR0_EDSS	(1 << 20)	/* Extended data size select */

drivers/spi/pxa2xx_spi.c

@@ -1318,14 +1318,14 @@ static int setup(struct spi_device *spi)
 	/* NOTE:  PXA25x_SSP _could_ use external clocking ... */
 	if (drv_data->ssp_type != PXA25x_SSP)
 		dev_dbg(&spi->dev, "%ld Hz actual, %s\n",
-				clk_get_rate(ssp->clk)
-					/ (1 + ((chip->cr0 & SSCR0_SCR) >> 8)),
-				chip->enable_dma ? "DMA" : "PIO");
+			clk_get_rate(ssp->clk)
+				/ (1 + ((chip->cr0 & SSCR0_SCR(0xfff)) >> 8)),
+			chip->enable_dma ? "DMA" : "PIO");
 	else
 		dev_dbg(&spi->dev, "%ld Hz actual, %s\n",
-				clk_get_rate(ssp->clk) / 2
-					/ (1 + ((chip->cr0 & SSCR0_SCR) >> 8)),
-				chip->enable_dma ? "DMA" : "PIO");
+			clk_get_rate(ssp->clk) / 2
+				/ (1 + ((chip->cr0 & SSCR0_SCR(0x0ff)) >> 8)),
+			chip->enable_dma ? "DMA" : "PIO");
 
 	if (spi->bits_per_word <= 8) {
 		chip->n_bytes = 1;
@@ -1558,7 +1558,7 @@ static int __init pxa2xx_spi_probe(struct platform_device *pdev)
 	write_SSCR1(SSCR1_RxTresh(RX_THRESH_DFLT) |
 				SSCR1_TxTresh(TX_THRESH_DFLT),
 				drv_data->ioaddr);
-	write_SSCR0(SSCR0_SerClkDiv(2)
+	write_SSCR0(SSCR0_SCR(2)
 			| SSCR0_Motorola
 			| SSCR0_DataSize(8),
 			drv_data->ioaddr);