Merge tag 'phy-for-4.14_v2' of...

Merge tag 'phy-for-4.14_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

Kishon writes:

phy: for 4.14

 *) Add USB PHY driver for Ralink SoC
 *) Make phy-mt65xx-usb3 driver support PCIe and SATA phy
 *) Add mediatek directory and rename phy-mt65xx-usb3 to phy-mtk-tphy.c
    since it now supports USB3.0, PCIe and SATA PHYs
 *) Make sun4i-usb-phy driver support USB PHYs for A83T SoC
 *) Make phy-qcom-qmp driver support USB PHYs for IPQ8074 SoC
 *) Make rockchip-inno-usb2 driver support usb2-phy for rv1108 SoC
 *) Minor fixes in phy drivers
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt → Documentation/devicetree/bindings/phy/phy-mtk-tphy.txt

-mt65xx USB3.0 PHY binding
+MediaTek T-PHY binding
 --------------------------
 
-This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC.
+T-phy controller supports physical layer functionality for a number of
+controllers on MediaTek SoCs, such as, USB2.0, USB3.0, PCIe, and SATA.
 
 Required properties (controller (parent) node):
  - compatible	: should be one of
-		  "mediatek,mt2701-u3phy"
-		  "mediatek,mt2712-u3phy"
-		  "mediatek,mt8173-u3phy"
+		  "mediatek,generic-tphy-v1"
+		  "mediatek,generic-tphy-v2"
+		  "mediatek,mt2701-u3phy" (deprecated)
+		  "mediatek,mt2712-u3phy" (deprecated)
+		  "mediatek,mt8173-u3phy";
+		  make use of "mediatek,generic-tphy-v1" on mt2701 instead and
+		  "mediatek,generic-tphy-v2" on mt2712 instead.
  - clocks	: (deprecated, use port's clocks instead) a list of phandle +
 		  clock-specifier pairs, one for each entry in clock-names
  - clock-names	: (deprecated, use port's one instead) must contain
@@ -35,6 +40,8 @@ Required properties (port (child) node):
 		  cell after port phandle is phy type from:
 			- PHY_TYPE_USB2
 			- PHY_TYPE_USB3
+			- PHY_TYPE_PCIE
+			- PHY_TYPE_SATA
 
 Example:
 

Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt

@@ -6,6 +6,7 @@ Required properties (phy (parent) node):
 	* "rockchip,rk3328-usb2phy"
 	* "rockchip,rk3366-usb2phy"
 	* "rockchip,rk3399-usb2phy"
+	* "rockchip,rv1108-usb2phy"
  - reg : the address offset of grf for usb-phy configuration.
  - #clock-cells : should be 0.
  - clock-output-names : specify the 480m output clock name.
@@ -18,6 +19,10 @@ Optional properties:
 		 usb-phy output 480m and xin24m.
 		 Refer to clk/clock-bindings.txt for generic clock
 		 consumer properties.
+ - rockchip,usbgrf : phandle to the syscon managing the "usb general
+		 register files". When set driver will request its
+		 phandle as one companion-grf for some special SoCs
+		 (e.g RV1108).
 
 Required nodes : a sub-node is required for each port the phy provides.
 		 The sub-node name is used to identify host or otg port,
@@ -28,10 +33,14 @@ Required nodes : a sub-node is required for each port the phy provides.
 Required properties (port (child) node):
  - #phy-cells : must be 0. See ./phy-bindings.txt for details.
  - interrupts : specify an interrupt for each entry in interrupt-names.
- - interrupt-names : a list which shall be the following entries:
+ - interrupt-names : a list which should be one of the following cases:
+	Regular case:
 	* "otg-id" : for the otg id interrupt.
 	* "otg-bvalid" : for the otg vbus interrupt.
 	* "linestate" : for the host/otg linestate interrupt.
+	Some SoCs use one interrupt with the above muxed together, so for these
+	* "otg-mux" : otg-port interrupt, which mux otg-id/otg-bvalid/linestate
+		to one.
 
 Optional properties:
  - phy-supply : phandle to a regulator that provides power to VBUS.

Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt

@@ -6,6 +6,7 @@ controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB.
 
 Required properties:
  - compatible: compatible list, contains:
+	       "qcom,ipq8074-qmp-pcie-phy" for PCIe phy on IPQ8074
 	       "qcom,msm8996-qmp-pcie-phy" for 14nm PCIe phy on msm8996,
 	       "qcom,msm8996-qmp-usb3-phy" for 14nm USB3 phy on msm8996.
 
@@ -38,6 +39,8 @@ Required properties:
 		 "phy", "common", "cfg".
 		For "qcom,msm8996-qmp-usb3-phy" must contain
 		 "phy", "common".
+		For "qcom,ipq8074-qmp-pcie-phy" must contain:
+		 "phy", "common".
 
  - vdda-phy-supply: Phandle to a regulator supply to PHY core block.
  - vdda-pll-supply: Phandle to 1.8V regulator supply to PHY refclk pll block.
@@ -60,6 +63,13 @@ Required properties for child node:
 	   one for each entry in clock-names.
  - clock-names: Must contain following for pcie and usb qmp phys:
 		 "pipe<lane-number>" for pipe clock specific to each lane.
+ - clock-output-names: Name of the PHY clock that will be the parent for
+		       the above pipe clock.
+
+	For "qcom,ipq8074-qmp-pcie-phy":
+		- "pcie20_phy0_pipe_clk"	Pipe Clock parent
+			(or)
+		  "pcie20_phy1_pipe_clk"
 
  - resets: a list of phandles and reset controller specifier pairs,
 	   one for each entry in reset-names.
@@ -96,6 +106,7 @@ Example:
 
 			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
 			clock-names = "pipe0";
+			clock-output-names = "pcie_0_pipe_clk_src";
 			resets = <&gcc GCC_PCIE_0_PHY_BCR>;
 			reset-names = "lane0";
 		};

Documentation/devicetree/bindings/phy/ralink-usb-phy.txt

+Mediatek/Ralink USB PHY
+
+Required properties:
+ - compatible: "ralink,rt3352-usbphy"
+	       "mediatek,mt7620-usbphy"
+	       "mediatek,mt7628-usbphy"
+ - reg: required for "mediatek,mt7628-usbphy", unused otherwise
+ - #phy-cells: should be 0
+ - ralink,sysctl: a phandle to a ralink syscon register region
+ - resets: the two reset controllers for host and device
+ - reset-names: the names of the 2 reset controllers
+
+Example:
+
+usbphy: phy {
+	compatible = "mediatek,mt7628-usbphy";
+	reg = <0x10120000 0x1000>;
+	#phy-cells = <0>;
+
+	ralink,sysctl = <&sysc>;
+	resets = <&rstctrl 22 &rstctrl 25>;
+	reset-names = "host", "device";
+};

Documentation/devicetree/bindings/phy/sun4i-usb-phy.txt

@@ -9,6 +9,7 @@ Required properties:
   * allwinner,sun7i-a20-usb-phy
   * allwinner,sun8i-a23-usb-phy
   * allwinner,sun8i-a33-usb-phy
+  * allwinner,sun8i-a83t-usb-phy
   * allwinner,sun8i-h3-usb-phy
   * allwinner,sun8i-v3s-usb-phy
   * allwinner,sun50i-a64-usb-phy
@@ -17,18 +18,22 @@ Required properties:
   * "phy_ctrl"
   * "pmu0" for H3, V3s and A64
   * "pmu1"
-  * "pmu2" for sun4i, sun6i or sun7i
+  * "pmu2" for sun4i, sun6i, sun7i, sun8i-a83t or sun8i-h3
+  * "pmu3" for sun8i-h3
 - #phy-cells : from the generic phy bindings, must be 1
 - clocks : phandle + clock specifier for the phy clocks
 - clock-names :
   * "usb_phy" for sun4i, sun5i or sun7i
   * "usb0_phy", "usb1_phy" and "usb2_phy" for sun6i
   * "usb0_phy", "usb1_phy" for sun8i
+  * "usb0_phy", "usb1_phy", "usb2_phy" and "usb2_hsic_12M" for sun8i-a83t
+  * "usb0_phy", "usb1_phy", "usb2_phy" and "usb3_phy" for sun8i-h3
 - resets : a list of phandle + reset specifier pairs
 - reset-names :
   * "usb0_reset"
   * "usb1_reset"
-  * "usb2_reset" for sun4i, sun6i or sun7i
+  * "usb2_reset" for sun4i, sun6i, sun7i, sun8i-a83t or sun8i-h3
+  * "usb3_reset" for sun8i-h3
 
 Optional properties:
 - usb0_id_det-gpios : gpio phandle for reading the otg id pin value
@@ -37,6 +42,7 @@ Optional properties:
 - usb0_vbus-supply : regulator phandle for controller usb0 vbus
 - usb1_vbus-supply : regulator phandle for controller usb1 vbus
 - usb2_vbus-supply : regulator phandle for controller usb2 vbus
+- usb3_vbus-supply : regulator phandle for controller usb3 vbus
 
 Example:
 	usbphy: phy@0x01c13400 {

MAINTAINERS

@@ -1570,7 +1570,7 @@ M:	Chunfeng Yun <chunfeng.yun@mediatek.com>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 L:	linux-mediatek@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
-F:	drivers/phy/phy-mt65xx-usb3.c
+F:	drivers/phy/mediatek/phy-mtk-tphy.c
 
 ARM/MICREL KS8695 ARCHITECTURE
 M:	Greg Ungerer <gerg@uclinux.org>

drivers/phy/Kconfig

@@ -26,14 +26,6 @@ config PHY_LPC18XX_USB_OTG
 	  This driver is need for USB0 support on LPC18xx/43xx and takes
 	  care of enabling and clock setup.
 
-config PHY_MT65XX_USB3
-	tristate "Mediatek USB3.0 PHY Driver"
-	depends on ARCH_MEDIATEK && OF
-	select GENERIC_PHY
-	help
-	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver,
-	  it supports multiple usb2.0 and usb3.0 ports.
-
 config PHY_PISTACHIO_USB
 	tristate "IMG Pistachio USB2.0 PHY driver"
 	depends on MACH_PISTACHIO
@@ -53,8 +45,10 @@ source "drivers/phy/amlogic/Kconfig"
 source "drivers/phy/broadcom/Kconfig"
 source "drivers/phy/hisilicon/Kconfig"
 source "drivers/phy/marvell/Kconfig"
+source "drivers/phy/mediatek/Kconfig"
 source "drivers/phy/motorola/Kconfig"
 source "drivers/phy/qualcomm/Kconfig"
+source "drivers/phy/ralink/Kconfig"
 source "drivers/phy/renesas/Kconfig"
 source "drivers/phy/rockchip/Kconfig"
 source "drivers/phy/samsung/Kconfig"

drivers/phy/Makefile

@@ -4,12 +4,12 @@
 
 obj-$(CONFIG_GENERIC_PHY)		+= phy-core.o
 obj-$(CONFIG_PHY_LPC18XX_USB_OTG)	+= phy-lpc18xx-usb-otg.o
-obj-$(CONFIG_PHY_MT65XX_USB3)		+= phy-mt65xx-usb3.o
 obj-$(CONFIG_PHY_XGENE)			+= phy-xgene.o
 obj-$(CONFIG_PHY_PISTACHIO_USB)		+= phy-pistachio-usb.o
 
 obj-$(CONFIG_ARCH_SUNXI)		+= allwinner/
 obj-$(CONFIG_ARCH_MESON)		+= amlogic/
+obj-$(CONFIG_ARCH_MEDIATEK)		+= mediatek/
 obj-$(CONFIG_ARCH_RENESAS)		+= renesas/
 obj-$(CONFIG_ARCH_ROCKCHIP)		+= rockchip/
 obj-$(CONFIG_ARCH_TEGRA)		+= tegra/
@@ -18,6 +18,7 @@ obj-y					+= broadcom/	\
 					   marvell/	\
 					   motorola/	\
 					   qualcomm/	\
+					   ralink/	\
 					   samsung/	\
 					   st/		\
 					   ti/

drivers/phy/allwinner/phy-sun4i-usb.c

@@ -87,6 +87,16 @@
 #define PHY_DISCON_TH_SEL		0x2a
 #define PHY_SQUELCH_DETECT		0x3c
 
+/* A83T specific control bits for PHY0 */
+#define PHY_CTL_VBUSVLDEXT		BIT(5)
+#define PHY_CTL_SIDDQ			BIT(3)
+
+/* A83T specific control bits for PHY2 HSIC */
+#define SUNXI_EHCI_HS_FORCE		BIT(20)
+#define SUNXI_HSIC_CONNECT_DET		BIT(17)
+#define SUNXI_HSIC_CONNECT_INT		BIT(16)
+#define SUNXI_HSIC			BIT(1)
+
 #define MAX_PHYS			4
 
 /*
@@ -100,6 +110,7 @@ enum sun4i_usb_phy_type {
 	sun4i_a10_phy,
 	sun6i_a31_phy,
 	sun8i_a33_phy,
+	sun8i_a83t_phy,
 	sun8i_h3_phy,
 	sun8i_v3s_phy,
 	sun50i_a64_phy,
@@ -107,6 +118,7 @@ enum sun4i_usb_phy_type {
 
 struct sun4i_usb_phy_cfg {
 	int num_phys;
+	int hsic_index;
 	enum sun4i_usb_phy_type type;
 	u32 disc_thresh;
 	u8 phyctl_offset;
@@ -126,6 +138,7 @@ struct sun4i_usb_phy_data {
 		struct regulator *vbus;
 		struct reset_control *reset;
 		struct clk *clk;
+		struct clk *clk2;
 		bool regulator_on;
 		int index;
 	} phys[MAX_PHYS];
@@ -232,6 +245,7 @@ static void sun4i_usb_phy_write(struct sun4i_usb_phy *phy, u32 addr, u32 data,
 
 static void sun4i_usb_phy_passby(struct sun4i_usb_phy *phy, int enable)
 {
+	struct sun4i_usb_phy_data *phy_data = to_sun4i_usb_phy_data(phy);
 	u32 bits, reg_value;
 
 	if (!phy->pmu)
@@ -240,6 +254,11 @@ static void sun4i_usb_phy_passby(struct sun4i_usb_phy *phy, int enable)
 	bits = SUNXI_AHB_ICHR8_EN | SUNXI_AHB_INCR4_BURST_EN |
 		SUNXI_AHB_INCRX_ALIGN_EN | SUNXI_ULPI_BYPASS_EN;
 
+	/* A83T USB2 is HSIC */
+	if (phy_data->cfg->type == sun8i_a83t_phy && phy->index == 2)
+		bits |= SUNXI_EHCI_HS_FORCE | SUNXI_HSIC_CONNECT_INT |
+			SUNXI_HSIC;
+
 	reg_value = readl(phy->pmu);
 
 	if (enable)
@@ -261,27 +280,43 @@ static int sun4i_usb_phy_init(struct phy *_phy)
 	if (ret)
 		return ret;
 
-	ret = reset_control_deassert(phy->reset);
+	ret = clk_prepare_enable(phy->clk2);
 	if (ret) {
 		clk_disable_unprepare(phy->clk);
 		return ret;
 	}
 
-	if (phy->pmu && data->cfg->enable_pmu_unk1) {
-		val = readl(phy->pmu + REG_PMU_UNK1);
-		writel(val & ~2, phy->pmu + REG_PMU_UNK1);
+	ret = reset_control_deassert(phy->reset);
+	if (ret) {
+		clk_disable_unprepare(phy->clk2);
+		clk_disable_unprepare(phy->clk);
+		return ret;
 	}
 
-	/* Enable USB 45 Ohm resistor calibration */
-	if (phy->index == 0)
-		sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1);
+	if (data->cfg->type == sun8i_a83t_phy) {
+		if (phy->index == 0) {
+			val = readl(data->base + data->cfg->phyctl_offset);
+			val |= PHY_CTL_VBUSVLDEXT;
+			val &= ~PHY_CTL_SIDDQ;
+			writel(val, data->base + data->cfg->phyctl_offset);
+		}
+	} else {
+		if (phy->pmu && data->cfg->enable_pmu_unk1) {
+			val = readl(phy->pmu + REG_PMU_UNK1);
+			writel(val & ~2, phy->pmu + REG_PMU_UNK1);
+		}
 
-	/* Adjust PHY's magnitude and rate */
-	sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE, 0x14, 5);
+		/* Enable USB 45 Ohm resistor calibration */
+		if (phy->index == 0)
+			sun4i_usb_phy_write(phy, PHY_RES45_CAL_EN, 0x01, 1);
 
-	/* Disconnect threshold adjustment */
-	sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL,
-			    data->cfg->disc_thresh, 2);
+		/* Adjust PHY's magnitude and rate */
+		sun4i_usb_phy_write(phy, PHY_TX_AMPLITUDE_TUNE, 0x14, 5);
+
+		/* Disconnect threshold adjustment */
+		sun4i_usb_phy_write(phy, PHY_DISCON_TH_SEL,
+				    data->cfg->disc_thresh, 2);
+	}
 
 	sun4i_usb_phy_passby(phy, 1);
 
@@ -307,6 +342,13 @@ static int sun4i_usb_phy_exit(struct phy *_phy)
 	struct sun4i_usb_phy_data *data = to_sun4i_usb_phy_data(phy);
 
 	if (phy->index == 0) {
+		if (data->cfg->type == sun8i_a83t_phy) {
+			void __iomem *phyctl = data->base +
+				data->cfg->phyctl_offset;
+
+			writel(readl(phyctl) | PHY_CTL_SIDDQ, phyctl);
+		}
+
 		/* Disable pull-ups */
 		sun4i_usb_phy0_update_iscr(_phy, ISCR_DPDM_PULLUP_EN, 0);
 		sun4i_usb_phy0_update_iscr(_phy, ISCR_ID_PULLUP_EN, 0);
@@ -315,6 +357,7 @@ static int sun4i_usb_phy_exit(struct phy *_phy)
 
 	sun4i_usb_phy_passby(phy, 0);
 	reset_control_assert(phy->reset);
+	clk_disable_unprepare(phy->clk2);
 	clk_disable_unprepare(phy->clk);
 
 	return 0;
@@ -653,19 +696,25 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
 
 	data->id_det_gpio = devm_gpiod_get_optional(dev, "usb0_id_det",
 						    GPIOD_IN);
-	if (IS_ERR(data->id_det_gpio))
+	if (IS_ERR(data->id_det_gpio)) {
+		dev_err(dev, "Couldn't request ID GPIO\n");
 		return PTR_ERR(data->id_det_gpio);
+	}
 
 	data->vbus_det_gpio = devm_gpiod_get_optional(dev, "usb0_vbus_det",
 						      GPIOD_IN);
-	if (IS_ERR(data->vbus_det_gpio))
+	if (IS_ERR(data->vbus_det_gpio)) {
+		dev_err(dev, "Couldn't request VBUS detect GPIO\n");
 		return PTR_ERR(data->vbus_det_gpio);
+	}
 
 	if (of_find_property(np, "usb0_vbus_power-supply", NULL)) {
 		data->vbus_power_supply = devm_power_supply_get_by_phandle(dev,
 						     "usb0_vbus_power-supply");
-		if (IS_ERR(data->vbus_power_supply))
+		if (IS_ERR(data->vbus_power_supply)) {
+			dev_err(dev, "Couldn't get the VBUS power supply\n");
 			return PTR_ERR(data->vbus_power_supply);
+		}
 
 		if (!data->vbus_power_supply)
 			return -EPROBE_DEFER;
@@ -674,8 +723,10 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
 	data->dr_mode = of_usb_get_dr_mode_by_phy(np, 0);
 
 	data->extcon = devm_extcon_dev_allocate(dev, sun4i_usb_phy0_cable);
-	if (IS_ERR(data->extcon))
+	if (IS_ERR(data->extcon)) {
+		dev_err(dev, "Couldn't allocate our extcon device\n");
 		return PTR_ERR(data->extcon);
+	}
 
 	ret = devm_extcon_dev_register(dev, data->extcon);
 	if (ret) {
@@ -690,8 +741,13 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
 		snprintf(name, sizeof(name), "usb%d_vbus", i);
 		phy->vbus = devm_regulator_get_optional(dev, name);
 		if (IS_ERR(phy->vbus)) {
-			if (PTR_ERR(phy->vbus) == -EPROBE_DEFER)
+			if (PTR_ERR(phy->vbus) == -EPROBE_DEFER) {
+				dev_err(dev,
+					"Couldn't get regulator %s... Deferring probe\n",
+					name);
 				return -EPROBE_DEFER;
+			}
+
 			phy->vbus = NULL;
 		}
 
@@ -706,6 +762,17 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
 			return PTR_ERR(phy->clk);
 		}
 
+		/* The first PHY is always tied to OTG, and never HSIC */
+		if (data->cfg->hsic_index && i == data->cfg->hsic_index) {
+			/* HSIC needs secondary clock */
+			snprintf(name, sizeof(name), "usb%d_hsic_12M", i);
+			phy->clk2 = devm_clk_get(dev, name);
+			if (IS_ERR(phy->clk2)) {
+				dev_err(dev, "failed to get clock %s\n", name);
+				return PTR_ERR(phy->clk2);
+			}
+		}
+
 		snprintf(name, sizeof(name), "usb%d_reset", i);
 		phy->reset = devm_reset_control_get(dev, name);
 		if (IS_ERR(phy->reset)) {
@@ -775,6 +842,8 @@ static int sun4i_usb_phy_probe(struct platform_device *pdev)
 		return PTR_ERR(phy_provider);
 	}
 
+	dev_dbg(dev, "successfully loaded\n");
+
 	return 0;
 }
 
@@ -832,6 +901,14 @@ static const struct sun4i_usb_phy_cfg sun8i_a33_cfg = {
 	.enable_pmu_unk1 = false,
 };
 
+static const struct sun4i_usb_phy_cfg sun8i_a83t_cfg = {
+	.num_phys = 3,
+	.hsic_index = 2,
+	.type = sun8i_a83t_phy,
+	.phyctl_offset = REG_PHYCTL_A33,
+	.dedicated_clocks = true,
+};
+
 static const struct sun4i_usb_phy_cfg sun8i_h3_cfg = {
 	.num_phys = 4,
 	.type = sun8i_h3_phy,
@@ -868,6 +945,7 @@ static const struct of_device_id sun4i_usb_phy_of_match[] = {
 	{ .compatible = "allwinner,sun7i-a20-usb-phy", .data = &sun7i_a20_cfg },
 	{ .compatible = "allwinner,sun8i-a23-usb-phy", .data = &sun8i_a23_cfg },
 	{ .compatible = "allwinner,sun8i-a33-usb-phy", .data = &sun8i_a33_cfg },
+	{ .compatible = "allwinner,sun8i-a83t-usb-phy", .data = &sun8i_a83t_cfg },
 	{ .compatible = "allwinner,sun8i-h3-usb-phy", .data = &sun8i_h3_cfg },
 	{ .compatible = "allwinner,sun8i-v3s-usb-phy", .data = &sun8i_v3s_cfg },
 	{ .compatible = "allwinner,sun50i-a64-usb-phy",

drivers/phy/broadcom/phy-brcm-sata.c

@@ -335,7 +335,7 @@ static int brcm_nsp_sata_init(struct brcm_sata_port *port)
 
 	/* Wait for pll_seq_done bit */
 	try = 50;
-	while (try--) {
+	while (--try) {
 		val = brcm_sata_phy_rd(base, BLOCK0_REG_BANK,
 					BLOCK0_XGXSSTATUS);
 		if (val & BLOCK0_XGXSSTATUS_PLL_LOCK)

drivers/phy/mediatek/Kconfig

+#
+# Phy drivers for Mediatek devices
+#
+config PHY_MTK_TPHY
+    tristate "MediaTek T-PHY Driver"
+    depends on ARCH_MEDIATEK && OF
+    select GENERIC_PHY
+    help
+      Say 'Y' here to add support for MediaTek T-PHY driver,
+      it supports multiple usb2.0, usb3.0 ports, PCIe and
+	  SATA, and meanwhile supports two version T-PHY which have
+	  different banks layout, the T-PHY with shared banks between
+	  multi-ports is first version, otherwise is second veriosn,
+	  so you can easily distinguish them by banks layout.

drivers/phy/mediatek/Makefile

+#
+# Makefile for the phy drivers.
+#
+
+obj-$(CONFIG_PHY_MTK_TPHY)		+= phy-mtk-tphy.o

drivers/phy/motorola/phy-cpcap-usb.c

@@ -506,7 +506,7 @@ static void cpcap_usb_init_optional_gpios(struct cpcap_phy_ddata *ddata)
 		if (IS_ERR(ddata->gpio[i])) {
 			dev_info(ddata->dev, "no mode change GPIO%i: %li\n",
 				 i, PTR_ERR(ddata->gpio[i]));
-				 ddata->gpio[i] = NULL;
+			ddata->gpio[i] = NULL;
 		}
 	}
 }

drivers/phy/qualcomm/phy-qcom-qmp.c

@@ -59,6 +59,7 @@
 #define QSERDES_COM_PLL_RCTRL_MODE1			0x088
 #define QSERDES_COM_PLL_CCTRL_MODE0			0x090
 #define QSERDES_COM_PLL_CCTRL_MODE1			0x094
+#define QSERDES_COM_BIAS_EN_CTRL_BY_PSM			0x0a8
 #define QSERDES_COM_SYSCLK_EN_SEL			0x0ac
 #define QSERDES_COM_RESETSM_CNTRL			0x0b4
 #define QSERDES_COM_RESTRIM_CTRL			0x0bc
@@ -143,6 +144,11 @@
 #define QPHY_LOCK_DETECT_CONFIG3			0x88
 #define QPHY_PWRUP_RESET_DLY_TIME_AUXCLK		0xa0
 #define QPHY_LP_WAKEUP_DLY_TIME_AUXCLK			0xa4
+#define QPHY_PLL_LOCK_CHK_DLY_TIME_AUXCLK_LSB		0x1A8
+#define QPHY_OSC_DTCT_ACTIONS				0x1AC
+#define QPHY_RX_SIGDET_LVL				0x1D8
+#define QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_LSB		0x1DC
+#define QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_MSB		0x1E0
 
 /* QPHY_SW_RESET bit */
 #define SW_RESET				BIT(0)
@@ -382,6 +388,85 @@ static const struct qmp_phy_init_tbl msm8996_usb3_pcs_tbl[] = {
 	QMP_PHY_INIT_CFG(QPHY_POWER_STATE_CONFIG2, 0x08),
 };
 
+static const struct qmp_phy_init_tbl ipq8074_pcie_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CLKBUFLR_EN, 0x18),
+	QMP_PHY_INIT_CFG(QSERDES_COM_CLK_ENABLE1, 0x10),
+	QMP_PHY_INIT_CFG(QSERDES_COM_BG_TRIM, 0xf),
+	QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP_EN, 0x1),
+	QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_MAP, 0x0),
+	QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER1, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_TIMER2, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x6),
+	QMP_PHY_INIT_CFG(QSERDES_COM_PLL_IVCO, 0xf),
+	QMP_PHY_INIT_CFG(QSERDES_COM_HSCLK_SEL, 0x0),
+	QMP_PHY_INIT_CFG(QSERDES_COM_SVS_MODE_CLK_SEL, 0x1),
+	QMP_PHY_INIT_CFG(QSERDES_COM_CORE_CLK_EN, 0x20),
+	QMP_PHY_INIT_CFG(QSERDES_COM_CORECLK_DIV, 0xa),
+	QMP_PHY_INIT_CFG(QSERDES_COM_RESETSM_CNTRL, 0x20),
+	QMP_PHY_INIT_CFG(QSERDES_COM_BG_TIMER, 0xa),
+	QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0xa),
+	QMP_PHY_INIT_CFG(QSERDES_COM_DEC_START_MODE0, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START3_MODE0, 0x3),
+	QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START2_MODE0, 0x55),
+	QMP_PHY_INIT_CFG(QSERDES_COM_DIV_FRAC_START1_MODE0, 0x55),
+	QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP3_MODE0, 0x0),
+	QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP2_MODE0, 0xD),
+	QMP_PHY_INIT_CFG(QSERDES_COM_LOCK_CMP1_MODE0, 0xD04),
+	QMP_PHY_INIT_CFG(QSERDES_COM_CLK_SELECT, 0x33),
+	QMP_PHY_INIT_CFG(QSERDES_COM_SYS_CLK_CTRL, 0x2),
+	QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_BUF_ENABLE, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_COM_CP_CTRL_MODE0, 0xb),
+	QMP_PHY_INIT_CFG(QSERDES_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_COM_PLL_CCTRL_MODE0, 0x28),
+	QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN1_MODE0, 0x0),
+	QMP_PHY_INIT_CFG(QSERDES_COM_INTEGLOOP_GAIN0_MODE0, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_COM_BIAS_EN_CTRL_BY_PSM, 0x1),
+	QMP_PHY_INIT_CFG(QSERDES_COM_VCO_TUNE_CTRL, 0xa),
+	QMP_PHY_INIT_CFG(QSERDES_COM_SSC_EN_CENTER, 0x1),
+	QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER1, 0x31),
+	QMP_PHY_INIT_CFG(QSERDES_COM_SSC_PER2, 0x1),
+	QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER1, 0x2),
+	QMP_PHY_INIT_CFG(QSERDES_COM_SSC_ADJ_PER2, 0x0),
+	QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE1, 0x2f),
+	QMP_PHY_INIT_CFG(QSERDES_COM_SSC_STEP_SIZE2, 0x19),
+	QMP_PHY_INIT_CFG(QSERDES_COM_CLK_EP_DIV, 0x19),
+	QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_CNTRL, 0x7),
+};
+
+static const struct qmp_phy_init_tbl ipq8074_pcie_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_TX_HIGHZ_TRANSCEIVEREN_BIAS_DRVR_EN, 0x45),
+	QMP_PHY_INIT_CFG(QSERDES_TX_LANE_MODE, 0x6),
+	QMP_PHY_INIT_CFG(QSERDES_TX_RES_CODE_LANE_OFFSET, 0x2),
+	QMP_PHY_INIT_CFG(QSERDES_TX_RCV_DETECT_LVL_2, 0x12),
+};
+
+static const struct qmp_phy_init_tbl ipq8074_pcie_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_ENABLES, 0x1c),
+	QMP_PHY_INIT_CFG(QSERDES_RX_SIGDET_DEGLITCH_CNTRL, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x1),
+	QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL3, 0x0),
+	QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL4, 0xdb),
+	QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x4b),
+	QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN, 0x4),
+	QMP_PHY_INIT_CFG(QSERDES_RX_UCDR_SO_GAIN_HALF, 0x4),
+};
+
+static const struct qmp_phy_init_tbl ipq8074_pcie_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_ENDPOINT_REFCLK_DRIVE, 0x4),
+	QMP_PHY_INIT_CFG(QPHY_OSC_DTCT_ACTIONS, 0x0),
+	QMP_PHY_INIT_CFG(QPHY_PWRUP_RESET_DLY_TIME_AUXCLK, 0x40),
+	QMP_PHY_INIT_CFG(QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_MSB, 0x0),
+	QMP_PHY_INIT_CFG(QPHY_L1SS_WAKEUP_DLY_TIME_AUXCLK_LSB, 0x40),
+	QMP_PHY_INIT_CFG(QPHY_PLL_LOCK_CHK_DLY_TIME_AUXCLK_LSB, 0x0),
+	QMP_PHY_INIT_CFG(QPHY_LP_WAKEUP_DLY_TIME_AUXCLK, 0x40),
+	QMP_PHY_INIT_CFG_L(QPHY_PLL_LOCK_CHK_DLY_TIME, 0x73),
+	QMP_PHY_INIT_CFG(QPHY_RX_SIGDET_LVL, 0x99),
+	QMP_PHY_INIT_CFG(QPHY_TXDEEMPH_M6DB_V0, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_TXDEEMPH_M3P5DB_V0, 0xe),
+	QMP_PHY_INIT_CFG_L(QPHY_SW_RESET, 0x0),
+	QMP_PHY_INIT_CFG_L(QPHY_START_CTRL, 0x3),
+};
+
 /* struct qmp_phy_cfg - per-PHY initialization config */
 struct qmp_phy_cfg {
 	/* phy-type - PCIE/UFS/USB */
@@ -580,6 +665,42 @@ static const struct qmp_phy_cfg msm8996_usb3phy_cfg = {
 	.mask_pcs_ready		= PHYSTATUS,
 };
 
+/* list of resets */
+static const char * const ipq8074_pciephy_reset_l[] = {
+	"phy", "common",
+};
+
+static const struct qmp_phy_cfg ipq8074_pciephy_cfg = {
+	.type			= PHY_TYPE_PCIE,
+	.nlanes			= 1,
+
+	.serdes_tbl		= ipq8074_pcie_serdes_tbl,
+	.serdes_tbl_num		= ARRAY_SIZE(ipq8074_pcie_serdes_tbl),
+	.tx_tbl			= ipq8074_pcie_tx_tbl,
+	.tx_tbl_num		= ARRAY_SIZE(ipq8074_pcie_tx_tbl),
+	.rx_tbl			= ipq8074_pcie_rx_tbl,
+	.rx_tbl_num		= ARRAY_SIZE(ipq8074_pcie_rx_tbl),
+	.pcs_tbl		= ipq8074_pcie_pcs_tbl,
+	.pcs_tbl_num		= ARRAY_SIZE(ipq8074_pcie_pcs_tbl),
+	.clk_list		= NULL,
+	.num_clks		= 0,
+	.reset_list		= ipq8074_pciephy_reset_l,
+	.num_resets		= ARRAY_SIZE(ipq8074_pciephy_reset_l),
+	.vreg_list		= NULL,
+	.num_vregs		= 0,
+	.regs			= pciephy_regs_layout,
+
+	.start_ctrl		= SERDES_START | PCS_START,
+	.pwrdn_ctrl		= SW_PWRDN | REFCLK_DRV_DSBL,
+	.mask_pcs_ready		= PHYSTATUS,
+
+	.has_phy_com_ctrl	= false,
+	.has_lane_rst		= false,
+	.has_pwrdn_delay	= true,
+	.pwrdn_delay_min	= 995,		/* us */
+	.pwrdn_delay_max	= 1005,		/* us */
+};
+
 static void qcom_qmp_phy_configure(void __iomem *base,
 				   const unsigned int *regs,
 				   const struct qmp_phy_init_tbl tbl[],
@@ -654,8 +775,6 @@ static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
 		if (ret) {
 			dev_err(qmp->dev, "%s reset deassert failed\n",
 				qmp->cfg->reset_list[i]);
-			while (--i >= 0)
-				reset_control_assert(qmp->resets[i]);
 			goto err_rst;
 		}
 	}
@@ -684,7 +803,7 @@ static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
 		if (ret) {
 			dev_err(qmp->dev,
 				"phy common block init timed-out\n");
-			goto err_com_init;
+			goto err_rst;
 		}
 	}
 
@@ -692,11 +811,11 @@ static int qcom_qmp_phy_com_init(struct qcom_qmp *qmp)
 
 	return 0;
 
-err_com_init:
+err_rst:
 	while (--i >= 0)
 		reset_control_assert(qmp->resets[i]);
-err_rst:
 	mutex_unlock(&qmp->phy_mutex);
+
 	return ret;
 }
 
@@ -749,14 +868,13 @@ static int qcom_qmp_phy_init(struct phy *phy)
 		if (ret) {
 			dev_err(qmp->dev, "failed to enable %s clk, err=%d\n",
 				qmp->cfg->clk_list[i], ret);
-			while (--i >= 0)
-				clk_disable_unprepare(qmp->clks[i]);
+			goto err_clk;
 		}
 	}
 
 	ret = qcom_qmp_phy_com_init(qmp);
 	if (ret)
-		goto err_com_init;
+		goto err_clk;
 
 	if (cfg->has_lane_rst) {
 		ret = reset_control_deassert(qphy->lane_rst);
@@ -804,7 +922,7 @@ static int qcom_qmp_phy_init(struct phy *phy)
 		reset_control_assert(qphy->lane_rst);
 err_lane_rst:
 	qcom_qmp_phy_com_exit(qmp);
-err_com_init:
+err_clk:
 	while (--i >= 0)
 		clk_disable_unprepare(qmp->clks[i]);
 
@@ -925,29 +1043,28 @@ static int qcom_qmp_phy_clk_init(struct device *dev)
  *    clk  |   +-------+   |                   +-----+
  *         +---------------+
  */
-static int phy_pipe_clk_register(struct qcom_qmp *qmp, int id)
+static int phy_pipe_clk_register(struct qcom_qmp *qmp, struct device_node *np)
 {
-	char name[24];
 	struct clk_fixed_rate *fixed;
 	struct clk_init_data init = { };
+	int ret;
 
-	switch (qmp->cfg->type) {
-	case PHY_TYPE_USB3:
-		snprintf(name, sizeof(name), "usb3_phy_pipe_clk_src");
-		break;
-	case PHY_TYPE_PCIE:
-		snprintf(name, sizeof(name), "pcie_%d_pipe_clk_src", id);
-		break;
-	default:
+	if ((qmp->cfg->type != PHY_TYPE_USB3) &&
+	    (qmp->cfg->type != PHY_TYPE_PCIE)) {
 		/* not all phys register pipe clocks, so return success */
 		return 0;
 	}
 
+	ret = of_property_read_string(np, "clock-output-names", &init.name);
+	if (ret) {
+		dev_err(qmp->dev, "%s: No clock-output-names\n", np->name);
+		return ret;
+	}
+
 	fixed = devm_kzalloc(qmp->dev, sizeof(*fixed), GFP_KERNEL);
 	if (!fixed)
 		return -ENOMEM;
 
-	init.name = name;
 	init.ops = &clk_fixed_rate_ops;
 
 	/* controllers using QMP phys use 125MHz pipe clock interface */
@@ -1049,6 +1166,9 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
 	}, {
 		.compatible = "qcom,msm8996-qmp-usb3-phy",
 		.data = &msm8996_usb3phy_cfg,
+	}, {
+		.compatible = "qcom,ipq8074-qmp-pcie-phy",
+		.data = &ipq8074_pciephy_cfg,
 	},
 	{ },
 };
@@ -1122,7 +1242,7 @@ static int qcom_qmp_phy_probe(struct platform_device *pdev)
 		 * Register the pipe clock provided by phy.
 		 * See function description to see details of this pipe clock.
 		 */
-		ret = phy_pipe_clk_register(qmp, id);
+		ret = phy_pipe_clk_register(qmp, child);
 		if (ret) {
 			dev_err(qmp->dev,
 				"failed to register pipe clock source\n");

drivers/phy/ralink/Kconfig

+#
+# PHY drivers for Ralink platforms.
+#
+config PHY_RALINK_USB
+	tristate "Ralink USB PHY driver"
+	depends on RALINK || COMPILE_TEST
+	select GENERIC_PHY
+	select MFD_SYSCON
+	help
+	  This option enables support for the Ralink USB PHY found inside
+	  RT3352, MT7620, MT7628 and MT7688.

drivers/phy/ralink/Makefile

+obj-$(CONFIG_PHY_RALINK_USB)	+= phy-ralink-usb.o

drivers/phy/ralink/phy-ralink-usb.c

+/*
+ * Copyright (C) 2017 John Crispin <john@phrozen.org>
+ *
+ * Based on code from
+ * Allwinner Technology Co., Ltd. <www.allwinnertech.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of_platform.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+#define RT_SYSC_REG_SYSCFG1		0x014
+#define RT_SYSC_REG_CLKCFG1		0x030
+#define RT_SYSC_REG_USB_PHY_CFG		0x05c
+
+#define OFS_U2_PHY_AC0			0x800
+#define OFS_U2_PHY_AC1			0x804
+#define OFS_U2_PHY_AC2			0x808
+#define OFS_U2_PHY_ACR0			0x810
+#define OFS_U2_PHY_ACR1			0x814
+#define OFS_U2_PHY_ACR2			0x818
+#define OFS_U2_PHY_ACR3			0x81C
+#define OFS_U2_PHY_ACR4			0x820
+#define OFS_U2_PHY_AMON0		0x824
+#define OFS_U2_PHY_DCR0			0x860
+#define OFS_U2_PHY_DCR1			0x864
+#define OFS_U2_PHY_DTM0			0x868
+#define OFS_U2_PHY_DTM1			0x86C
+
+#define RT_RSTCTRL_UDEV			BIT(25)
+#define RT_RSTCTRL_UHST			BIT(22)
+#define RT_SYSCFG1_USB0_HOST_MODE	BIT(10)
+
+#define MT7620_CLKCFG1_UPHY0_CLK_EN	BIT(25)
+#define MT7620_CLKCFG1_UPHY1_CLK_EN	BIT(22)
+#define RT_CLKCFG1_UPHY1_CLK_EN		BIT(20)
+#define RT_CLKCFG1_UPHY0_CLK_EN		BIT(18)
+
+#define USB_PHY_UTMI_8B60M		BIT(1)
+#define UDEV_WAKEUP			BIT(0)
+
+struct ralink_usb_phy {
+	struct reset_control	*rstdev;
+	struct reset_control	*rsthost;
+	u32			clk;
+	struct phy		*phy;
+	void __iomem		*base;
+	struct regmap		*sysctl;
+};
+
+static void u2_phy_w32(struct ralink_usb_phy *phy, u32 val, u32 reg)
+{
+	writel(val, phy->base + reg);
+}
+
+static u32 u2_phy_r32(struct ralink_usb_phy *phy, u32 reg)
+{
+	return readl(phy->base + reg);
+}
+
+static void ralink_usb_phy_init(struct ralink_usb_phy *phy)
+{
+	u2_phy_r32(phy, OFS_U2_PHY_AC2);
+	u2_phy_r32(phy, OFS_U2_PHY_ACR0);
+	u2_phy_r32(phy, OFS_U2_PHY_DCR0);
+
+	u2_phy_w32(phy, 0x00ffff02, OFS_U2_PHY_DCR0);
+	u2_phy_r32(phy, OFS_U2_PHY_DCR0);
+	u2_phy_w32(phy, 0x00555502, OFS_U2_PHY_DCR0);
+	u2_phy_r32(phy, OFS_U2_PHY_DCR0);
+	u2_phy_w32(phy, 0x00aaaa02, OFS_U2_PHY_DCR0);
+	u2_phy_r32(phy, OFS_U2_PHY_DCR0);
+	u2_phy_w32(phy, 0x00000402, OFS_U2_PHY_DCR0);
+	u2_phy_r32(phy, OFS_U2_PHY_DCR0);
+	u2_phy_w32(phy, 0x0048086a, OFS_U2_PHY_AC0);
+	u2_phy_w32(phy, 0x4400001c, OFS_U2_PHY_AC1);
+	u2_phy_w32(phy, 0xc0200000, OFS_U2_PHY_ACR3);
+	u2_phy_w32(phy, 0x02000000, OFS_U2_PHY_DTM0);
+}
+
+static int ralink_usb_phy_power_on(struct phy *_phy)
+{
+	struct ralink_usb_phy *phy = phy_get_drvdata(_phy);
+	u32 t;
+
+	/* enable the phy */
+	regmap_update_bits(phy->sysctl, RT_SYSC_REG_CLKCFG1,
+			   phy->clk, phy->clk);
+
+	/* setup host mode */
+	regmap_update_bits(phy->sysctl, RT_SYSC_REG_SYSCFG1,
+			   RT_SYSCFG1_USB0_HOST_MODE,
+			   RT_SYSCFG1_USB0_HOST_MODE);
+
+	/* deassert the reset lines */
+	reset_control_deassert(phy->rsthost);
+	reset_control_deassert(phy->rstdev);
+
+	/*
+	 * The SDK kernel had a delay of 100ms. however on device
+	 * testing showed that 10ms is enough
+	 */
+	mdelay(10);
+
+	if (phy->base)
+		ralink_usb_phy_init(phy);
+
+	/* print some status info */
+	regmap_read(phy->sysctl, RT_SYSC_REG_USB_PHY_CFG, &t);
+	dev_info(&phy->phy->dev, "remote usb device wakeup %s\n",
+		(t & UDEV_WAKEUP) ? ("enabled") : ("disabled"));
+	if (t & USB_PHY_UTMI_8B60M)
+		dev_info(&phy->phy->dev, "UTMI 8bit 60MHz\n");
+	else
+		dev_info(&phy->phy->dev, "UTMI 16bit 30MHz\n");
+
+	return 0;
+}
+
+static int ralink_usb_phy_power_off(struct phy *_phy)
+{
+	struct ralink_usb_phy *phy = phy_get_drvdata(_phy);
+
+	/* disable the phy */
+	regmap_update_bits(phy->sysctl, RT_SYSC_REG_CLKCFG1,
+			   phy->clk, 0);
+
+	/* assert the reset lines */
+	reset_control_assert(phy->rstdev);
+	reset_control_assert(phy->rsthost);
+
+	return 0;
+}
+
+static struct phy_ops ralink_usb_phy_ops = {
+	.power_on	= ralink_usb_phy_power_on,
+	.power_off	= ralink_usb_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static const struct of_device_id ralink_usb_phy_of_match[] = {
+	{
+		.compatible = "ralink,rt3352-usbphy",
+		.data = (void *) (RT_CLKCFG1_UPHY1_CLK_EN |
+				  RT_CLKCFG1_UPHY0_CLK_EN)
+	},
+	{
+		.compatible = "mediatek,mt7620-usbphy",
+		.data = (void *) (MT7620_CLKCFG1_UPHY1_CLK_EN |
+				  MT7620_CLKCFG1_UPHY0_CLK_EN)
+	},
+	{
+		.compatible = "mediatek,mt7628-usbphy",
+		.data = (void *) (MT7620_CLKCFG1_UPHY1_CLK_EN |
+				  MT7620_CLKCFG1_UPHY0_CLK_EN) },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, ralink_usb_phy_of_match);
+
+static int ralink_usb_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	struct phy_provider *phy_provider;
+	const struct of_device_id *match;
+	struct ralink_usb_phy *phy;
+
+	match = of_match_device(ralink_usb_phy_of_match, &pdev->dev);
+	if (!match)
+		return -ENODEV;
+
+	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
+	if (!phy)
+		return -ENOMEM;
+
+	phy->clk = (u32) match->data;
+	phy->base = NULL;
+
+	phy->sysctl = syscon_regmap_lookup_by_phandle(dev->of_node, "ralink,sysctl");
+	if (IS_ERR(phy->sysctl)) {
+		dev_err(dev, "failed to get sysctl registers\n");
+		return PTR_ERR(phy->sysctl);
+	}
+
+	/* The MT7628 and MT7688 require extra setup of PHY registers. */
+	if (of_device_is_compatible(dev->of_node, "mediatek,mt7628-usbphy")) {
+		res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+		phy->base = devm_ioremap_resource(&pdev->dev, res);
+		if (IS_ERR(phy->base)) {
+			dev_err(dev, "failed to remap register memory\n");
+			return PTR_ERR(phy->base);
+		}
+	}
+
+	phy->rsthost = devm_reset_control_get(&pdev->dev, "host");
+	if (IS_ERR(phy->rsthost)) {
+		dev_err(dev, "host reset is missing\n");
+		return PTR_ERR(phy->rsthost);
+	}
+
+	phy->rstdev = devm_reset_control_get(&pdev->dev, "device");
+	if (IS_ERR(phy->rstdev)) {
+		dev_err(dev, "device reset is missing\n");
+		return PTR_ERR(phy->rstdev);
+	}
+
+	phy->phy = devm_phy_create(dev, NULL, &ralink_usb_phy_ops);
+	if (IS_ERR(phy->phy)) {
+		dev_err(dev, "failed to create PHY\n");
+		return PTR_ERR(phy->phy);
+	}
+	phy_set_drvdata(phy->phy, phy);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static struct platform_driver ralink_usb_phy_driver = {
+	.probe	= ralink_usb_phy_probe,
+	.driver = {
+		.of_match_table	= ralink_usb_phy_of_match,
+		.name  = "ralink-usb-phy",
+	}
+};
+module_platform_driver(ralink_usb_phy_driver);
+
+MODULE_DESCRIPTION("Ralink USB phy driver");
+MODULE_AUTHOR("John Crispin <john@phrozen.org>");
+MODULE_LICENSE("GPL v2");

drivers/phy/rockchip/phy-rockchip-typec.c

@@ -622,12 +622,11 @@ static int tcphy_get_mode(struct rockchip_typec_phy *tcphy)
 	struct extcon_dev *edev = tcphy->extcon;
 	union extcon_property_value property;
 	unsigned int id;
-	bool dfp, ufp, dp;
+	bool ufp, dp;
 	u8 mode;
 	int ret;
 
 	ufp = extcon_get_state(edev, EXTCON_USB);
-	dfp = extcon_get_state(edev, EXTCON_USB_HOST);
 	dp = extcon_get_state(edev, EXTCON_DISP_DP);
 
 	mode = MODE_DFP_USB;

drivers/phy/samsung/phy-exynos-dp-video.c

@@ -16,6 +16,7 @@
 #include <linux/mfd/syscon.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
+#include <linux/of_device.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
@@ -78,7 +79,6 @@ static int exynos_dp_video_phy_probe(struct platform_device *pdev)
 {
 	struct exynos_dp_video_phy *state;
 	struct device *dev = &pdev->dev;
-	const struct of_device_id *match;
 	struct phy_provider *phy_provider;
 	struct phy *phy;
 
@@ -93,8 +93,7 @@ static int exynos_dp_video_phy_probe(struct platform_device *pdev)
 		return PTR_ERR(state->regs);
 	}
 
-	match = of_match_node(exynos_dp_video_phy_of_match, dev->of_node);
-	state->drvdata = match->data;
+	state->drvdata = of_device_get_match_data(dev);
 
 	phy = devm_phy_create(dev, NULL, &exynos_dp_video_phy_ops);
 	if (IS_ERR(phy)) {

drivers/phy/samsung/phy-exynos5-usbdrd.c

@@ -18,6 +18,7 @@
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
+#include <linux/of_device.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
 #include <linux/mutex.h>
@@ -662,7 +663,6 @@ static int exynos5_usbdrd_phy_probe(struct platform_device *pdev)
 	struct exynos5_usbdrd_phy *phy_drd;
 	struct phy_provider *phy_provider;
 	struct resource *res;
-	const struct of_device_id *match;
 	const struct exynos5_usbdrd_phy_drvdata *drv_data;
 	struct regmap *reg_pmu;
 	u32 pmu_offset;
@@ -681,9 +681,10 @@ static int exynos5_usbdrd_phy_probe(struct platform_device *pdev)
 	if (IS_ERR(phy_drd->reg_phy))
 		return PTR_ERR(phy_drd->reg_phy);
 
-	match = of_match_node(exynos5_usbdrd_phy_of_match, pdev->dev.of_node);
+	drv_data = of_device_get_match_data(dev);
+	if (!drv_data)
+		return -EINVAL;
 
-	drv_data = match->data;
 	phy_drd->drv_data = drv_data;
 
 	ret = exynos5_usbdrd_phy_clk_handle(phy_drd);

drivers/phy/samsung/phy-samsung-usb2.c

@@ -14,6 +14,7 @@
 #include <linux/module.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
+#include <linux/of_device.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
 #include <linux/spinlock.h>
@@ -142,7 +143,6 @@ MODULE_DEVICE_TABLE(of, samsung_usb2_phy_of_match);
 
 static int samsung_usb2_phy_probe(struct platform_device *pdev)
 {
-	const struct of_device_id *match;
 	const struct samsung_usb2_phy_config *cfg;
 	struct device *dev = &pdev->dev;
 	struct phy_provider *phy_provider;
@@ -155,12 +155,9 @@ static int samsung_usb2_phy_probe(struct platform_device *pdev)
 		return -EINVAL;
 	}
 
-	match = of_match_node(samsung_usb2_phy_of_match, pdev->dev.of_node);
-	if (!match) {
-		dev_err(dev, "of_match_node() failed\n");
+	cfg = of_device_get_match_data(dev);
+	if (!cfg)
 		return -EINVAL;
-	}
-	cfg = match->data;
 
 	drv = devm_kzalloc(dev, sizeof(struct samsung_usb2_phy_driver) +
 		cfg->num_phys * sizeof(struct samsung_usb2_phy_instance),

drivers/phy/ti/phy-ti-pipe3.c

@@ -118,12 +118,12 @@ static struct pipe3_dpll_map dpll_map_usb[] = {
 };
 
 static struct pipe3_dpll_map dpll_map_sata[] = {
-	{12000000, {1000, 7, 4, 6, 0} },	/* 12 MHz */
-	{16800000, {714, 7, 4, 6, 0} },		/* 16.8 MHz */
+	{12000000, {625, 4, 4, 6, 0} },	/* 12 MHz */
+	{16800000, {625, 6, 4, 7, 0} },		/* 16.8 MHz */
 	{19200000, {625, 7, 4, 6, 0} },		/* 19.2 MHz */
-	{20000000, {600, 7, 4, 6, 0} },		/* 20 MHz */
-	{26000000, {461, 7, 4, 6, 0} },		/* 26 MHz */
-	{38400000, {312, 7, 4, 6, 0} },		/* 38.4 MHz */
+	{20000000, {750, 9, 4, 6, 0} },		/* 20 MHz */
+	{26000000, {750, 12, 4, 6, 0} },	/* 26 MHz */
+	{38400000, {625, 15, 4, 6, 0} },	/* 38.4 MHz */
 	{ },					/* Terminator */
 };
 

drivers/phy/ti/phy-twl4030-usb.c

@@ -185,7 +185,7 @@ struct twl4030_usb {
 static int twl4030_i2c_write_u8_verify(struct twl4030_usb *twl,
 		u8 module, u8 data, u8 address)
 {
-	u8 check;
+	u8 check = 0xFF;
 
 	if ((twl_i2c_write_u8(module, data, address) >= 0) &&
 	    (twl_i2c_read_u8(module, &check, address) >= 0) &&