Merge branch 'topic/r820t' into patchwork

* topic/r820t: (31 commits)
  [media] r820t: Don't divide the IF by two
  [media] r820t: disable auto gain/VGA setting
  [media] rtl2832: Fix IF calculus
  [media] r820t: put it into automatic gain mode
  [media] r820t: Fix hp_cor filter mask
  [media] r820t: fix PLL calculus
  [media] r820t: Don't put it in standby if not initialized yet
  [media] r820t: avoid rewrite all regs when not needed
  [media] r820t: Allow disabling IMR callibration
  [media] r820t: add a commented code for GPIO
  [media] r820t: add IMR calibrate code
  [media] r820t: proper initialize the PLL register
  [media] r820t: use usleep_range()
  [media] r820t: fix prefix of the r820t_read() function
  [media] r820t: split the function that read cached regs
  [media] r820t: better report signal strength
  [media] r820t: add support for diplexer
  [media] r820t: Show the read data in the bit-reversed order
  [media] r820t: use the second table for 7MHz
  [media] r820t: Invert bits for read ops
  ...

drivers/media/dvb-frontends/rtl2832.c

@@ -380,13 +380,41 @@ static int rtl2832_i2c_gate_ctrl(struct dvb_frontend *fe, int enable)
 	return ret;
 }
 
-static int rtl2832_init(struct dvb_frontend *fe)
+
+static int rtl2832_set_if(struct dvb_frontend *fe, u32 if_freq)
 {
 	struct rtl2832_priv *priv = fe->demodulator_priv;
-	int i, ret, len;
-	u8 en_bbin;
+	int ret;
 	u64 pset_iffreq;
+	u8 en_bbin = (if_freq == 0 ? 0x1 : 0x0);
+
+	/*
+	* PSET_IFFREQ = - floor((IfFreqHz % CrystalFreqHz) * pow(2, 22)
+	*		/ CrystalFreqHz)
+	*/
+
+	pset_iffreq = if_freq % priv->cfg.xtal;
+	pset_iffreq *= 0x400000;
+	pset_iffreq = div_u64(pset_iffreq, priv->cfg.xtal);
+	pset_iffreq = -pset_iffreq;
+	pset_iffreq = pset_iffreq & 0x3fffff;
+	dev_dbg(&priv->i2c->dev, "%s: if_frequency=%d pset_iffreq=%08x\n",
+			__func__, if_freq, (unsigned)pset_iffreq);
+
+	ret = rtl2832_wr_demod_reg(priv, DVBT_EN_BBIN, en_bbin);
+	if (ret)
+		return ret;
+
+	ret = rtl2832_wr_demod_reg(priv, DVBT_PSET_IFFREQ, pset_iffreq);
+
+	return (ret);
+}
+
+static int rtl2832_init(struct dvb_frontend *fe)
+{
+	struct rtl2832_priv *priv = fe->demodulator_priv;
 	const struct rtl2832_reg_value *init;
+	int i, ret, len;
 
 	/* initialization values for the demodulator registers */
 	struct rtl2832_reg_value rtl2832_initial_regs[] = {
@@ -432,22 +460,10 @@ static int rtl2832_init(struct dvb_frontend *fe)
 		{DVBT_TR_THD_SET2,		0x6},
 		{DVBT_TRK_KC_I2,		0x5},
 		{DVBT_CR_THD_SET2,		0x1},
-		{DVBT_SPEC_INV,			0x0},
 	};
 
 	dev_dbg(&priv->i2c->dev, "%s:\n", __func__);
 
-	en_bbin = (priv->cfg.if_dvbt == 0 ? 0x1 : 0x0);
-
-	/*
-	* PSET_IFFREQ = - floor((IfFreqHz % CrystalFreqHz) * pow(2, 22)
-	*		/ CrystalFreqHz)
-	*/
-	pset_iffreq = priv->cfg.if_dvbt % priv->cfg.xtal;
-	pset_iffreq *= 0x400000;
-	pset_iffreq = div_u64(pset_iffreq, priv->cfg.xtal);
-	pset_iffreq = pset_iffreq & 0x3fffff;
-
 	for (i = 0; i < ARRAY_SIZE(rtl2832_initial_regs); i++) {
 		ret = rtl2832_wr_demod_reg(priv, rtl2832_initial_regs[i].reg,
 			rtl2832_initial_regs[i].value);
@@ -472,6 +488,10 @@ static int rtl2832_init(struct dvb_frontend *fe)
 		len = ARRAY_SIZE(rtl2832_tuner_init_e4000);
 		init = rtl2832_tuner_init_e4000;
 		break;
+	case RTL2832_TUNER_R820T:
+		len = ARRAY_SIZE(rtl2832_tuner_init_r820t);
+		init = rtl2832_tuner_init_r820t;
+		break;
 	default:
 		ret = -EINVAL;
 		goto err;
@@ -483,14 +503,26 @@ static int rtl2832_init(struct dvb_frontend *fe)
 			goto err;
 	}
 
-	/* if frequency settings */
-	ret = rtl2832_wr_demod_reg(priv, DVBT_EN_BBIN, en_bbin);
+	if (!fe->ops.tuner_ops.get_if_frequency) {
+		ret = rtl2832_set_if(fe, priv->cfg.if_dvbt);
 		if (ret)
 			goto err;
+	}
 
-	ret = rtl2832_wr_demod_reg(priv, DVBT_PSET_IFFREQ, pset_iffreq);
-		if (ret)
-			goto err;
+	/*
+	 * r820t NIM code does a software reset here at the demod -
+	 * may not be needed, as there's already a software reset at set_params()
+	 */
+#if 1
+	/* soft reset */
+	ret = rtl2832_wr_demod_reg(priv, DVBT_SOFT_RST, 0x1);
+	if (ret)
+		goto err;
+
+	ret = rtl2832_wr_demod_reg(priv, DVBT_SOFT_RST, 0x0);
+	if (ret)
+		goto err;
+#endif
 
 	priv->sleeping = false;
 
@@ -564,6 +596,19 @@ static int rtl2832_set_frontend(struct dvb_frontend *fe)
 	if (fe->ops.tuner_ops.set_params)
 		fe->ops.tuner_ops.set_params(fe);
 
+	/* If the frontend has get_if_frequency(), use it */
+	if (fe->ops.tuner_ops.get_if_frequency) {
+		u32 if_freq;
+
+		ret = fe->ops.tuner_ops.get_if_frequency(fe, &if_freq);
+		if (ret)
+			goto err;
+
+		ret = rtl2832_set_if(fe, if_freq);
+		if (ret)
+			goto err;
+	}
+
 	switch (c->bandwidth_hz) {
 	case 6000000:
 		i = 0;

drivers/media/dvb-frontends/rtl2832.h

@@ -52,6 +52,7 @@ struct rtl2832_config {
 #define RTL2832_TUNER_FC0012    0x26
 #define RTL2832_TUNER_E4000     0x27
 #define RTL2832_TUNER_FC0013    0x29
+#define RTL2832_TUNER_R820T	0x2a
 	u8 tuner;
 };
 

drivers/media/dvb-frontends/rtl2832_priv.h

@@ -267,6 +267,7 @@ static const struct rtl2832_reg_value rtl2832_tuner_init_tua9001[] = {
 	{DVBT_OPT_ADC_IQ,                0x1},
 	{DVBT_AD_AVI,                    0x0},
 	{DVBT_AD_AVQ,                    0x0},
+	{DVBT_SPEC_INV,			 0x0},
 };
 
 static const struct rtl2832_reg_value rtl2832_tuner_init_fc0012[] = {
@@ -300,6 +301,7 @@ static const struct rtl2832_reg_value rtl2832_tuner_init_fc0012[] = {
 	{DVBT_GI_PGA_STATE,              0x0},
 	{DVBT_EN_AGC_PGA,                0x1},
 	{DVBT_IF_AGC_MAN,                0x0},
+	{DVBT_SPEC_INV,			 0x0},
 };
 
 static const struct rtl2832_reg_value rtl2832_tuner_init_e4000[] = {
@@ -337,6 +339,32 @@ static const struct rtl2832_reg_value rtl2832_tuner_init_e4000[] = {
 	{DVBT_REG_MONSEL,                0x1},
 	{DVBT_REG_MON,                   0x1},
 	{DVBT_REG_4MSEL,                 0x0},
+	{DVBT_SPEC_INV,			 0x0},
+};
+
+static const struct rtl2832_reg_value rtl2832_tuner_init_r820t[] = {
+	{DVBT_DAGC_TRG_VAL,		0x39},
+	{DVBT_AGC_TARG_VAL_0,		0x0},
+	{DVBT_AGC_TARG_VAL_8_1,		0x40},
+	{DVBT_AAGC_LOOP_GAIN,		0x16},
+	{DVBT_LOOP_GAIN2_3_0,		0x8},
+	{DVBT_LOOP_GAIN2_4,		0x1},
+	{DVBT_LOOP_GAIN3,		0x18},
+	{DVBT_VTOP1,			0x35},
+	{DVBT_VTOP2,			0x21},
+	{DVBT_VTOP3,			0x21},
+	{DVBT_KRF1,			0x0},
+	{DVBT_KRF2,			0x40},
+	{DVBT_KRF3,			0x10},
+	{DVBT_KRF4,			0x10},
+	{DVBT_IF_AGC_MIN,		0x80},
+	{DVBT_IF_AGC_MAX,		0x7f},
+	{DVBT_RF_AGC_MIN,		0x80},
+	{DVBT_RF_AGC_MAX,		0x7f},
+	{DVBT_POLAR_RF_AGC,		0x0},
+	{DVBT_POLAR_IF_AGC,		0x0},
+	{DVBT_AD7_SETTING,		0xe9f4},
+	{DVBT_SPEC_INV,			0x1},
 };
 
 #endif /* RTL2832_PRIV_H */

drivers/media/tuners/Kconfig

@@ -248,4 +248,11 @@ config MEDIA_TUNER_IT913X
 	default m if !MEDIA_SUBDRV_AUTOSELECT
 	help
 	  ITE Tech IT913x silicon tuner driver.
+
+config MEDIA_TUNER_R820T
+	tristate "Rafael Micro R820T silicon tuner"
+	depends on MEDIA_SUPPORT && I2C
+	default m if !MEDIA_SUBDRV_AUTOSELECT
+	help
+	  Rafael Micro R820T silicon tuner driver.
 endmenu

drivers/media/tuners/Makefile

@@ -35,6 +35,7 @@ obj-$(CONFIG_MEDIA_TUNER_FC0011) += fc0011.o
 obj-$(CONFIG_MEDIA_TUNER_FC0012) += fc0012.o
 obj-$(CONFIG_MEDIA_TUNER_FC0013) += fc0013.o
 obj-$(CONFIG_MEDIA_TUNER_IT913X) += tuner_it913x.o
+obj-$(CONFIG_MEDIA_TUNER_R820T) += r820t.o
 
 ccflags-y += -I$(srctree)/drivers/media/dvb-core
 ccflags-y += -I$(srctree)/drivers/media/dvb-frontends

drivers/media/tuners/r820t.h

+/*
+ * Elonics R820T silicon tuner driver
+ *
+ * Copyright (C) 2012 Antti Palosaari <crope@iki.fi>
+ *
+ *    This program is free software; you can redistribute it and/or modify
+ *    it under the terms of the GNU General Public License as published by
+ *    the Free Software Foundation; either version 2 of the License, or
+ *    (at your option) any later version.
+ *
+ *    This program is distributed in the hope that it will be useful,
+ *    but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *    GNU General Public License for more details.
+ *
+ *    You should have received a copy of the GNU General Public License along
+ *    with this program; if not, write to the Free Software Foundation, Inc.,
+ *    51 Franklin Street, Fifth Floor, Boston, MA 02110-1301 USA.
+ */
+
+#ifndef R820T_H
+#define R820T_H
+
+#include <linux/kconfig.h>
+#include "dvb_frontend.h"
+
+enum r820t_chip {
+	CHIP_R820T,
+	CHIP_R620D,
+	CHIP_R828D,
+	CHIP_R828,
+	CHIP_R828S,
+	CHIP_R820C,
+};
+
+struct r820t_config {
+	u8 i2c_addr;		/* 0x34 */
+	u32 xtal;
+	enum r820t_chip rafael_chip;
+	unsigned max_i2c_msg_len;
+	bool use_diplexer;
+};
+
+#if IS_ENABLED(CONFIG_MEDIA_TUNER_R820T)
+struct dvb_frontend *r820t_attach(struct dvb_frontend *fe,
+				  struct i2c_adapter *i2c,
+				  const struct r820t_config *cfg);
+#else
+static inline struct dvb_frontend *r820t_attach(struct dvb_frontend *fe,
+						struct i2c_adapter *i2c,
+						const struct r820t_config *cfg)
+{
+	pr_warn("%s: driver disabled by Kconfig\n", __func__);
+	return NULL;
+}
+#endif
+
+#endif

drivers/media/usb/dvb-usb-v2/Kconfig

@@ -143,6 +143,7 @@ config DVB_USB_RTL28XXU
 	select MEDIA_TUNER_FC0013 if MEDIA_SUBDRV_AUTOSELECT
 	select MEDIA_TUNER_E4000 if MEDIA_SUBDRV_AUTOSELECT
 	select MEDIA_TUNER_FC2580 if MEDIA_SUBDRV_AUTOSELECT
+	select MEDIA_TUNER_R820T if MEDIA_SUBDRV_AUTOSELECT
 	help
 	  Say Y here to support the Realtek RTL28xxU DVB USB receiver.
 

drivers/media/usb/dvb-usb-v2/rtl28xxu.c

@@ -33,6 +33,7 @@
 #include "e4000.h"
 #include "fc2580.h"
 #include "tua9001.h"
+#include "r820t.h"
 
 DVB_DEFINE_MOD_OPT_ADAPTER_NR(adapter_nr);
 
@@ -375,6 +376,7 @@ static int rtl2832u_read_config(struct dvb_usb_device *d)
 	struct rtl28xxu_req req_mxl5007t = {0xd9c0, CMD_I2C_RD, 1, buf};
 	struct rtl28xxu_req req_e4000 = {0x02c8, CMD_I2C_RD, 1, buf};
 	struct rtl28xxu_req req_tda18272 = {0x00c0, CMD_I2C_RD, 2, buf};
+	struct rtl28xxu_req req_r820t = {0x0034, CMD_I2C_RD, 5, buf};
 
 	dev_dbg(&d->udev->dev, "%s:\n", __func__);
 
@@ -479,6 +481,14 @@ static int rtl2832u_read_config(struct dvb_usb_device *d)
 		goto found;
 	}
 
+	/* check R820T by reading tuner stats at I2C addr 0x1a */
+	ret = rtl28xxu_ctrl_msg(d, &req_r820t);
+	if (ret == 0) {
+		priv->tuner = TUNER_RTL2832_R820T;
+		priv->tuner_name = "R820T";
+		goto found;
+	}
+
 found:
 	dev_dbg(&d->udev->dev, "%s: tuner=%s\n", __func__, priv->tuner_name);
 
@@ -589,6 +599,12 @@ static struct rtl2832_config rtl28xxu_rtl2832_e4000_config = {
 	.tuner = TUNER_RTL2832_E4000,
 };
 
+static struct rtl2832_config rtl28xxu_rtl2832_r820t_config = {
+	.i2c_addr = 0x10,
+	.xtal = 28800000,
+	.tuner = TUNER_RTL2832_R820T,
+};
+
 static int rtl2832u_fc0012_tuner_callback(struct dvb_usb_device *d,
 		int cmd, int arg)
 {
@@ -728,6 +744,9 @@ static int rtl2832u_frontend_attach(struct dvb_usb_adapter *adap)
 	case TUNER_RTL2832_E4000:
 		rtl2832_config = &rtl28xxu_rtl2832_e4000_config;
 		break;
+	case TUNER_RTL2832_R820T:
+		rtl2832_config = &rtl28xxu_rtl2832_r820t_config;
+		break;
 	default:
 		dev_err(&d->udev->dev, "%s: unknown tuner=%s\n",
 				KBUILD_MODNAME, priv->tuner_name);
@@ -840,6 +859,13 @@ static const struct fc0012_config rtl2832u_fc0012_config = {
 	.xtal_freq = FC_XTAL_28_8_MHZ,
 };
 
+static const struct r820t_config rtl2832u_r820t_config = {
+	.i2c_addr = 0x1a,
+	.xtal = 28800000,
+	.max_i2c_msg_len = 2,
+	.rafael_chip = CHIP_R820T,
+};
+
 static int rtl2832u_tuner_attach(struct dvb_usb_adapter *adap)
 {
 	int ret;
@@ -889,6 +915,14 @@ static int rtl2832u_tuner_attach(struct dvb_usb_adapter *adap)
 		fe = dvb_attach(tua9001_attach, adap->fe[0], &d->i2c_adap,
 				&rtl2832u_tua9001_config);
 		break;
+	case TUNER_RTL2832_R820T:
+		fe = dvb_attach(r820t_attach, adap->fe[0], &d->i2c_adap,
+				&rtl2832u_r820t_config);
+
+		/* Use tuner to get the signal strength */
+		adap->fe[0]->ops.read_signal_strength =
+				adap->fe[0]->ops.tuner_ops.get_rf_strength;
+		break;
 	default:
 		fe = NULL;
 		dev_err(&d->udev->dev, "%s: unknown tuner=%d\n", KBUILD_MODNAME,

drivers/media/usb/dvb-usb-v2/rtl28xxu.h

@@ -82,6 +82,7 @@ enum rtl28xxu_tuner {
 	TUNER_RTL2832_E4000,
 	TUNER_RTL2832_TDA18272,
 	TUNER_RTL2832_FC0013,
+	TUNER_RTL2832_R820T,
 };
 
 struct rtl28xxu_req {