serial: stm32: update throttle and unthrottle ops for dma mode

Disable DMA request line (if enabled) to switch in PIO mode in throttle
ops, so the RX data gets queues into the FIFO. The hardware flow control
is triggered when the RX FIFO is full.

Switch back to DMA mode (re-enable DMA request line) in unthrottle ops.
Hardware flow control is stopped when FIFO is not full anymore.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20211020150332.10214-4-erwan.leray@foss.st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/stm32-usart.c

@@ -577,9 +577,12 @@ static irqreturn_t stm32_usart_interrupt(int irq, void *ptr)
 	 * rx errors in dma mode has to be handled ASAP to avoid overrun as the DMA request
 	 * line has been masked by HW and rx data are stacking in FIFO.
 	 */
-	if (((sr & USART_SR_RXNE) && !stm32_usart_rx_dma_enabled(port)) ||
-	    ((sr & USART_SR_ERR_MASK) && stm32_usart_rx_dma_enabled(port)))
-		stm32_usart_receive_chars(port, false);
+	if (!stm32_port->throttled) {
+		if (((sr & USART_SR_RXNE) && !stm32_usart_rx_dma_enabled(port)) ||
+		    ((sr & USART_SR_ERR_MASK) && stm32_usart_rx_dma_enabled(port))) {
+			stm32_usart_receive_chars(port, false);
+		}
+	}
 
 	if ((sr & USART_SR_TXE) && !(stm32_port->tx_ch)) {
 		spin_lock(&port->lock);
@@ -596,9 +599,11 @@ static irqreturn_t stm32_usart_interrupt(int irq, void *ptr)
 static irqreturn_t stm32_usart_threaded_interrupt(int irq, void *ptr)
 {
 	struct uart_port *port = ptr;
+	struct stm32_port *stm32_port = to_stm32_port(port);
 
 	/* Receiver timeout irq for DMA RX */
-	stm32_usart_receive_chars(port, false);
+	if (!stm32_port->throttled)
+		stm32_usart_receive_chars(port, false);
 
 	return IRQ_HANDLED;
 }
@@ -711,10 +716,19 @@ static void stm32_usart_throttle(struct uart_port *port)
 	unsigned long flags;
 
 	spin_lock_irqsave(&port->lock, flags);
+
+	/*
+	 * Disable DMA request line if enabled, so the RX data gets queued into the FIFO.
+	 * Hardware flow control is triggered when RX FIFO is full.
+	 */
+	if (stm32_usart_rx_dma_enabled(port))
+		stm32_usart_clr_bits(port, ofs->cr3, USART_CR3_DMAR);
+
 	stm32_usart_clr_bits(port, ofs->cr1, stm32_port->cr1_irq);
 	if (stm32_port->cr3_irq)
 		stm32_usart_clr_bits(port, ofs->cr3, stm32_port->cr3_irq);
 
+	stm32_port->throttled = true;
 	spin_unlock_irqrestore(&port->lock, flags);
 }
 
@@ -730,6 +744,14 @@ static void stm32_usart_unthrottle(struct uart_port *port)
 	if (stm32_port->cr3_irq)
 		stm32_usart_set_bits(port, ofs->cr3, stm32_port->cr3_irq);
 
+	/*
+	 * Switch back to DMA mode (re-enable DMA request line).
+	 * Hardware flow control is stopped when FIFO is not full any more.
+	 */
+	if (stm32_port->rx_ch)
+		stm32_usart_set_bits(port, ofs->cr3, USART_CR3_DMAR);
+
+	stm32_port->throttled = false;
 	spin_unlock_irqrestore(&port->lock, flags);
 }
 
@@ -775,6 +797,13 @@ static int stm32_usart_startup(struct uart_port *port)
 	if (ofs->rqr != UNDEF_REG)
 		writel_relaxed(USART_RQR_RXFRQ, port->membase + ofs->rqr);
 
+	/*
+	 * DMA request line not re-enabled at resume when port is throttled.
+	 * It will be re-enabled by unthrottle ops.
+	 */
+	if (!stm32_port->throttled)
+		stm32_usart_set_bits(port, ofs->cr3, USART_CR3_DMAR);
+
 	/* RX enabling */
 	val = stm32_port->cr1_irq | USART_CR1_RE | BIT(cfg->uart_enable_bit);
 	stm32_usart_set_bits(port, ofs->cr1, val);

drivers/tty/serial/stm32-usart.h

@@ -265,6 +265,7 @@ struct stm32_port {
 	u32 cr3_irq;		 /* USART_CR3_RXFTIE */
 	int last_res;
 	bool tx_dma_busy;	 /* dma tx busy               */
+	bool throttled;		 /* port throttled            */
 	bool hw_flow_control;
 	bool swap;		 /* swap RX & TX pins */
 	bool fifoen;