usb: musb: remove references to default_a of struct usb_otg

musb drivers do not use the otg fsm framework, so referencing to
otg->default_a doesn't have any effect, so remove the references.

But tusb6010 glue driver uses it locally to control the vbus power, so
keep the references in tusb6010 only.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/musb/am35x.c

@@ -201,7 +201,6 @@ static irqreturn_t am35x_musb_interrupt(int irq, void *hci)
 	struct device *dev = musb->controller;
 	struct musb_hdrc_platform_data *plat = dev_get_platdata(dev);
 	struct omap_musb_board_data *data = plat->board_data;
-	struct usb_otg *otg = musb->xceiv->otg;
 	unsigned long flags;
 	irqreturn_t ret = IRQ_NONE;
 	u32 epintr, usbintr;
@@ -264,14 +263,12 @@ static irqreturn_t am35x_musb_interrupt(int irq, void *hci)
 			WARNING("VBUS error workaround (delay coming)\n");
 		} else if (drvvbus) {
 			MUSB_HST_MODE(musb);
-			otg->default_a = 1;
 			musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
 			portstate(musb->port1_status |= USB_PORT_STAT_POWER);
 			del_timer(&musb->dev_timer);
 		} else {
 			musb->is_active = 0;
 			MUSB_DEV_MODE(musb);
-			otg->default_a = 0;
 			musb->xceiv->otg->state = OTG_STATE_B_IDLE;
 			portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
 		}

drivers/usb/musb/da8xx.c

@@ -280,7 +280,6 @@ static irqreturn_t da8xx_musb_interrupt(int irq, void *hci)
 			WARNING("VBUS error workaround (delay coming)\n");
 		} else if (drvvbus) {
 			MUSB_HST_MODE(musb);
-			otg->default_a = 1;
 			musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
 			portstate(musb->port1_status |= USB_PORT_STAT_POWER);
 			del_timer(&musb->dev_timer);
@@ -295,7 +294,6 @@ static irqreturn_t da8xx_musb_interrupt(int irq, void *hci)
 			 */
 			musb->is_active = 0;
 			MUSB_DEV_MODE(musb);
-			otg->default_a = 0;
 			musb->xceiv->otg->state = OTG_STATE_B_IDLE;
 			portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
 		}

drivers/usb/musb/davinci.c

@@ -311,14 +311,12 @@ static irqreturn_t davinci_musb_interrupt(int irq, void *__hci)
 			WARNING("VBUS error workaround (delay coming)\n");
 		} else if (drvvbus) {
 			MUSB_HST_MODE(musb);
-			otg->default_a = 1;
 			musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
 			portstate(musb->port1_status |= USB_PORT_STAT_POWER);
 			del_timer(&musb->dev_timer);
 		} else {
 			musb->is_active = 0;
 			MUSB_DEV_MODE(musb);
-			otg->default_a = 0;
 			musb->xceiv->otg->state = OTG_STATE_B_IDLE;
 			portstate(musb->port1_status &= ~USB_PORT_STAT_POWER);
 		}
@@ -425,6 +423,9 @@ static int davinci_musb_init(struct musb *musb)
 
 static int davinci_musb_exit(struct musb *musb)
 {
+	int	maxdelay = 30;
+	u8	devctl, warn = 0;
+
 	del_timer_sync(&musb->dev_timer);
 
 	/* force VBUS off */
@@ -438,31 +439,27 @@ static int davinci_musb_exit(struct musb *musb)
 
 	davinci_musb_source_power(musb, 0 /*off*/, 1);
 
-	/* delay, to avoid problems with module reload */
-	if (musb->xceiv->otg->default_a) {
-		int	maxdelay = 30;
-		u8	devctl, warn = 0;
+	/*
+	 * delay, to avoid problems with module reload.
+	 * if there's no peripheral connected, this can take a
+	 * long time to fall, especially on EVM with huge C133.
+	 */
+	do {
+		devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
+		if (!(devctl & MUSB_DEVCTL_VBUS))
+			break;
+		if ((devctl & MUSB_DEVCTL_VBUS) != warn) {
+			warn = devctl & MUSB_DEVCTL_VBUS;
+			dev_dbg(musb->controller, "VBUS %d\n",
+				warn >> MUSB_DEVCTL_VBUS_SHIFT);
+		}
+		msleep(1000);
+		maxdelay--;
+	} while (maxdelay > 0);
 
-		/* if there's no peripheral connected, this can take a
-		 * long time to fall, especially on EVM with huge C133.
-		 */
-		do {
-			devctl = musb_readb(musb->mregs, MUSB_DEVCTL);
-			if (!(devctl & MUSB_DEVCTL_VBUS))
-				break;
-			if ((devctl & MUSB_DEVCTL_VBUS) != warn) {
-				warn = devctl & MUSB_DEVCTL_VBUS;
-				dev_dbg(musb->controller, "VBUS %d\n",
-					warn >> MUSB_DEVCTL_VBUS_SHIFT);
-			}
-			msleep(1000);
-			maxdelay--;
-		} while (maxdelay > 0);
-
-		/* in OTG mode, another host might be connected */
-		if (devctl & MUSB_DEVCTL_VBUS)
-			dev_dbg(musb->controller, "VBUS off timeout (devctl %02x)\n", devctl);
-	}
+	/* in OTG mode, another host might be connected */
+	if (devctl & MUSB_DEVCTL_VBUS)
+		dev_dbg(musb->controller, "VBUS off timeout (devctl %02x)\n", devctl);
 
 	phy_off();
 

drivers/usb/musb/musb_core.c

@@ -2352,13 +2352,8 @@ musb_init_controller(struct device *dev, int nIrq, void __iomem *ctrl)
 		musb_writeb(musb->mregs, MUSB_ULPI_BUSCONTROL, busctl);
 	}
 
-	if (musb->xceiv->otg->default_a) {
-		MUSB_HST_MODE(musb);
-		musb->xceiv->otg->state = OTG_STATE_A_IDLE;
-	} else {
-		MUSB_DEV_MODE(musb);
-		musb->xceiv->otg->state = OTG_STATE_B_IDLE;
-	}
+	MUSB_DEV_MODE(musb);
+	musb->xceiv->otg->state = OTG_STATE_B_IDLE;
 
 	switch (musb->port_mode) {
 	case MUSB_HOST:

drivers/usb/musb/musb_dsps.c

@@ -360,13 +360,11 @@ static irqreturn_t dsps_interrupt(int irq, void *hci)
 			WARNING("VBUS error workaround (delay coming)\n");
 		} else if (drvvbus) {
 			MUSB_HST_MODE(musb);
-			musb->xceiv->otg->default_a = 1;
 			musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
 			dsps_mod_timer_optional(glue);
 		} else {
 			musb->is_active = 0;
 			MUSB_DEV_MODE(musb);
-			musb->xceiv->otg->default_a = 0;
 			musb->xceiv->otg->state = OTG_STATE_B_IDLE;
 		}
 

drivers/usb/musb/musb_gadget.c

@@ -1794,7 +1794,6 @@ int musb_gadget_setup(struct musb *musb)
 	musb->g.speed = USB_SPEED_UNKNOWN;
 
 	MUSB_DEV_MODE(musb);
-	musb->xceiv->otg->default_a = 0;
 	musb->xceiv->otg->state = OTG_STATE_B_IDLE;
 
 	/* this "gadget" abstracts/virtualizes the controller */

drivers/usb/musb/musb_host.c

@@ -2752,7 +2752,6 @@ int musb_host_setup(struct musb *musb, int power_budget)
 
 	if (musb->port_mode == MUSB_HOST) {
 		MUSB_HST_MODE(musb);
-		musb->xceiv->otg->default_a = 1;
 		musb->xceiv->otg->state = OTG_STATE_A_IDLE;
 	}
 	otg_set_host(musb->xceiv->otg, &hcd->self);

drivers/usb/musb/omap2430.c

@@ -77,7 +77,6 @@ static void omap2430_musb_set_vbus(struct musb *musb, int is_on)
 			otg_set_vbus(otg, 1);
 		} else {
 			musb->is_active = 1;
-			otg->default_a = 1;
 			musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
 			devctl |= MUSB_DEVCTL_SESSION;
 			MUSB_HST_MODE(musb);
@@ -89,7 +88,6 @@ static void omap2430_musb_set_vbus(struct musb *musb, int is_on)
 		 * jumping right to B_IDLE...
 		 */
 
-		otg->default_a = 0;
 		musb->xceiv->otg->state = OTG_STATE_B_IDLE;
 		devctl &= ~MUSB_DEVCTL_SESSION;
 
@@ -148,14 +146,12 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue)
 	struct musb_hdrc_platform_data *pdata =
 		dev_get_platdata(musb->controller);
 	struct omap_musb_board_data *data = pdata->board_data;
-	struct usb_otg *otg = musb->xceiv->otg;
 
 	pm_runtime_get_sync(musb->controller);
 	switch (glue->status) {
 	case MUSB_ID_GROUND:
 		dev_dbg(musb->controller, "ID GND\n");
 
-		otg->default_a = true;
 		musb->xceiv->otg->state = OTG_STATE_A_IDLE;
 		musb->xceiv->last_event = USB_EVENT_ID;
 		if (musb->gadget_driver) {
@@ -168,7 +164,6 @@ static void omap_musb_set_mailbox(struct omap2430_glue *glue)
 	case MUSB_VBUS_VALID:
 		dev_dbg(musb->controller, "VBUS Connect\n");
 
-		otg->default_a = false;
 		musb->xceiv->otg->state = OTG_STATE_B_IDLE;
 		musb->xceiv->last_event = USB_EVENT_VBUS;
 		omap_control_usb_set_mode(glue->control_otghs, USB_MODE_DEVICE);

drivers/usb/musb/sunxi.c

@@ -105,13 +105,11 @@ static void sunxi_musb_work(struct work_struct *work)
 		devctl = readb(musb->mregs + SUNXI_MUSB_DEVCTL);
 		if (test_bit(SUNXI_MUSB_FL_HOSTMODE, &glue->flags)) {
 			set_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
-			musb->xceiv->otg->default_a = 1;
 			musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
 			MUSB_HST_MODE(musb);
 			devctl |= MUSB_DEVCTL_SESSION;
 		} else {
 			clear_bit(SUNXI_MUSB_FL_VBUS_ON, &glue->flags);
-			musb->xceiv->otg->default_a = 0;
 			musb->xceiv->otg->state = OTG_STATE_B_IDLE;
 			MUSB_DEV_MODE(musb);
 			devctl &= ~MUSB_DEVCTL_SESSION;

drivers/usb/musb/ux500.c

@@ -62,7 +62,6 @@ static void ux500_musb_set_vbus(struct musb *musb, int is_on)
 
 		} else {
 			musb->is_active = 1;
-			musb->xceiv->otg->default_a = 1;
 			musb->xceiv->otg->state = OTG_STATE_A_WAIT_VRISE;
 			devctl |= MUSB_DEVCTL_SESSION;
 			MUSB_HST_MODE(musb);
@@ -73,7 +72,6 @@ static void ux500_musb_set_vbus(struct musb *musb, int is_on)
 		/* NOTE: we're skipping A_WAIT_VFALL -> A_IDLE and jumping
 		 * right to B_IDLE...
 		 */
-		musb->xceiv->otg->default_a = 0;
 		devctl &= ~MUSB_DEVCTL_SESSION;
 		MUSB_DEV_MODE(musb);
 	}