arm64: dts: qcom: sc8180x: Add pmics

SC8180X based platforms have PM8150, PM8150C, PMC8180 and SMB2351 PMICs,
so add these as well
Co-developed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230530162454.51708-14-vkoul@kernel.org

arch/arm64/boot/dts/qcom/sc8180x-pmics.dtsi

+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2021-2023, Linaro Limited
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/spmi/spmi.h>
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+
+/ {
+	thermal-zones {
+		pmc8180-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pmc8180_temp>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+
+		pmc8180c-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <0>;
+
+			thermal-sensors = <&pmc8180c_temp>;
+
+			trips {
+				trip0 {
+					temperature = <95000>;
+					hysteresis = <0>;
+					type = "passive";
+				};
+
+				trip1 {
+					temperature = <115000>;
+					hysteresis = <0>;
+					type = "hot";
+				};
+
+				trip2 {
+					temperature = <145000>;
+					hysteresis = <0>;
+					type = "critical";
+				};
+			};
+		};
+	};
+};
+
+&spmi_bus {
+	pmc8180_0: pmic@0 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x0 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pon: power-on@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x0800>;
+			pwrkey {
+				compatible = "qcom,pm8941-pwrkey";
+				interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
+				debounce = <15625>;
+				bias-pull-up;
+				linux,code = <KEY_POWER>;
+
+				status = "disabled";
+			};
+		};
+
+		pmc8180_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			io-channels = <&pmc8180_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmc8180_adc: adc@3100 {
+			compatible = "qcom,spmi-adc5";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			die-temp@6 {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "die_temp";
+			};
+		};
+
+		pmc8180_adc_tm: adc-tm@3500 {
+			compatible = "qcom,spmi-adc-tm5";
+			reg = <0x3500>;
+			interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		rtc@6000 {
+			compatible = "qcom,pm8941-rtc";
+			reg = <0x6000>;
+			reg-names = "rtc", "alarm";
+			interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
+		};
+
+		pmc8180_gpios: gpio@c000 {
+			compatible = "qcom,pmc8180-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmic@1 {
+		compatible = "qcom,pmc8180", "qcom,spmi-pmic";
+		reg = <0x1 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	pmic@2 {
+		compatible = "qcom,smb2351", "qcom,spmi-pmic";
+		reg = <0x2 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		adc@3100 {
+			compatible = "qcom,spmi-adc-rev2";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			vcoin@85 {
+				reg = <0x85>;
+				qcom,pre-scaling = <1 1>;
+				label = "vcoin2";
+			};
+		};
+	};
+
+	pmic@6 {
+		compatible = "qcom,pm8150c", "qcom,spmi-pmic";
+		reg = <0x6 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	pmic@8 {
+		compatible = "qcom,pm8150", "qcom,spmi-pmic";
+		reg = <0x8 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	pmic@a {
+		compatible = "qcom,smb2351", "qcom,spmi-pmic";
+		reg = <0xa SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		adc@3100 {
+			compatible = "qcom,spmi-adc-rev2";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0xa 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			vcoin@85 {
+				reg = <0x85>;
+				qcom,pre-scaling = <1 1>;
+				label = "vcoin";
+			};
+		};
+	};
+
+	pmic@4 {
+		compatible = "qcom,pm8150c", "qcom,spmi-pmic";
+		reg = <0x4 SPMI_USID>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		power-on@800 {
+			compatible = "qcom,pm8916-pon";
+			reg = <0x0800>;
+
+			status = "disabled";
+		};
+
+		pmc8180c_temp: temp-alarm@2400 {
+			compatible = "qcom,spmi-temp-alarm";
+			reg = <0x2400>;
+			interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
+			io-channels = <&pmc8180c_adc ADC5_DIE_TEMP>;
+			io-channel-names = "thermal";
+			#thermal-sensor-cells = <0>;
+		};
+
+		pmc8180c_adc: adc@3100 {
+			compatible = "qcom,spmi-adc5";
+			reg = <0x3100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#io-channel-cells = <1>;
+			interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+
+			ref-gnd@0 {
+				reg = <ADC5_REF_GND>;
+				qcom,pre-scaling = <1 1>;
+				label = "ref_gnd";
+			};
+
+			vref-1p25@1 {
+				reg = <ADC5_1P25VREF>;
+				qcom,pre-scaling = <1 1>;
+				label = "vref_1p25";
+			};
+
+			die-temp@6 {
+				reg = <ADC5_DIE_TEMP>;
+				qcom,pre-scaling = <1 1>;
+				label = "die_temp";
+			};
+		};
+
+		pmc8180c_adc_tm: adc-tm@3500 {
+			compatible = "qcom,spmi-adc-tm5";
+			reg = <0x3500>;
+			interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
+			#thermal-sensor-cells = <1>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "disabled";
+		};
+
+		pmc8180c_gpios: gpio@c000 {
+			compatible = "qcom,pmc8180c-gpio";
+			reg = <0xc000>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+	};
+
+	pmic@5 {
+		compatible = "qcom,pmc8180c", "qcom,spmi-pmic";
+		reg = <0x5 SPMI_USID>;
+
+		pmc8180c_lpg: lpg {
+			compatible = "qcom,pmc8180c-lpg";
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			#pwm-cells = <2>;
+
+			status = "disabled";
+		};
+	};
+};