Commit d400f209 authored by Venu Byravarasu's avatar Venu Byravarasu Committed by Stephen Warren

ARM: tegra: finalize USB EHCI and PHY bindings

The existing Tegra USB bindings have a few issues:

1) Many properties are documented as being part of the EHCI controller
node, yet they apply more to the PHY device. They should be moved.

2) Some registers in PHY1 are shared with PHY3, and hence PHY3 needs a
reg entry to point at PHY1's register space. We can't assume the PHY1
driver is present, so the PHY3 driver will directly access those
registers.

3) The list of clocks required by the PHY was missing some required
entries.

4) UTMI PHY Timing parameters are added

5) VBUS control is now specified using a regulator rather than a plain GPIO

6) Added nvidia,is-wired property to indicate whether the device is
hard wired on the board, or pluggable.

This patch fixes the binding definition to resolve these issues.
Signed-off-by: default avatarVenu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: default avatarStephen Warren <swarren@nvidia.com>
parent f722406f
...@@ -6,27 +6,10 @@ Practice : Universal Serial Bus" with the following modifications ...@@ -6,27 +6,10 @@ Practice : Universal Serial Bus" with the following modifications
and additions : and additions :
Required properties : Required properties :
- compatible : Should be "nvidia,tegra20-ehci" for USB controllers - compatible : Should be "nvidia,tegra20-ehci".
used in host mode. - nvidia,phy : phandle of the PHY that the controller is connected to.
- phy_type : Should be one of "ulpi" or "utmi". - clocks : Contains a single entry which defines the USB controller's clock.
- nvidia,vbus-gpio : If present, specifies a gpio that needs to be
activated for the bus to be powered.
- nvidia,phy : phandle of the PHY instance, the controller is connected to.
Required properties for phy_type == ulpi:
- nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
Optional properties: Optional properties:
- dr_mode : dual role mode. Indicates the working mode for - nvidia,needs-double-reset : boolean is to be set for some of the Tegra20
nvidia,tegra20-ehci compatible controllers. Can be "host", "peripheral", USB ports, which need reset twice due to hardware issues.
or "otg". Default to "host" if not defined for backward compatibility.
host means this is a host controller
peripheral means it is device controller
otg means it can operate as either ("on the go")
- nvidia,has-legacy-mode : boolean indicates whether this controller can
operate in legacy mode (as APX 2500 / 2600). In legacy mode some
registers are accessed through the APB_MISC base address instead of
the USB controller. Since this is a legacy issue it probably does not
warrant a compatible string of its own.
- nvidia,needs-double-reset : boolean is to be set for some of the Tegra2
USB ports, which need reset twice due to hardware issues.
...@@ -4,14 +4,49 @@ The device node for Tegra SOC USB PHY: ...@@ -4,14 +4,49 @@ The device node for Tegra SOC USB PHY:
Required properties : Required properties :
- compatible : Should be "nvidia,tegra20-usb-phy". - compatible : Should be "nvidia,tegra20-usb-phy".
- reg : Address and length of the register set for the USB PHY interface. - reg : Defines the following set of registers, in the order listed:
- phy_type : Should be one of "ulpi" or "utmi". - The PHY's own register set.
Always present.
- The register set of the PHY containing the UTMI pad control registers.
Present if-and-only-if phy_type == utmi.
- phy_type : Should be one of "utmi", "ulpi" or "hsic".
- clocks : Defines the clocks listed in the clock-names property.
- clock-names : The following clock names must be present:
- reg: The clock needed to access the PHY's own registers. This is the
associated EHCI controller's clock. Always present.
- pll_u: PLL_U. Always present.
- timer: The timeout clock (clk_m). Present if phy_type == utmi.
- utmi-pads: The clock needed to access the UTMI pad control registers.
Present if phy_type == utmi.
- ulpi-link: The clock Tegra provides to the ULPI PHY (cdev2).
Present if phy_type == ulpi, and ULPI link mode is in use.
Required properties for phy_type == ulpi: Required properties for phy_type == ulpi:
- nvidia,phy-reset-gpio : The GPIO used to reset the PHY. - nvidia,phy-reset-gpio : The GPIO used to reset the PHY.
Required PHY timing params for utmi phy:
- nvidia,hssync-start-delay : Number of 480 Mhz clock cycles to wait before
start of sync launches RxActive
- nvidia,elastic-limit : Variable FIFO Depth of elastic input store
- nvidia,idle-wait-delay : Number of 480 Mhz clock cycles of idle to wait
before declare IDLE.
- nvidia,term-range-adj : Range adjusment on terminations
- nvidia,xcvr-setup : HS driver output control
- nvidia,xcvr-lsfslew : LS falling slew rate control.
- nvidia,xcvr-lsrslew : LS rising slew rate control.
Optional properties: Optional properties:
- nvidia,has-legacy-mode : boolean indicates whether this controller can - nvidia,has-legacy-mode : boolean indicates whether this controller can
operate in legacy mode (as APX 2500 / 2600). In legacy mode some operate in legacy mode (as APX 2500 / 2600). In legacy mode some
registers are accessed through the APB_MISC base address instead of registers are accessed through the APB_MISC base address instead of
the USB controller. the USB controller.
\ No newline at end of file - nvidia,is-wired : boolean. Indicates whether we can do certain kind of power
optimizations for the devices that are always connected. e.g. modem.
- dr_mode : dual role mode. Indicates the working mode for the PHY. Can be
"host", "peripheral", or "otg". Defaults to "host" if not defined.
host means this is a host controller
peripheral means it is device controller
otg means it can operate as either ("on the go")
Required properties for dr_mode == otg:
- vbus-supply: regulator for VBUS
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment