Commit d510d12f authored by Pavel Machek's avatar Pavel Machek Committed by Tony Lindgren

ARM: dts: nokia n900: update dts with camera support

Add camera support to N900 dts. Also add a note about MMC & debugging.
Signed-off-by: default avatarPavel Machek <pavel@ucw.cz>
Acked-by: default avatarPali Rohár <pali.rohar@gmail.com>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
parent 895bd4b3
......@@ -144,6 +144,15 @@ battery: n900-battery {
io-channel-names = "temp", "bsi", "vbat";
};
rear_camera: camera@0 {
compatible = "linux,camera";
module {
model = "TCM8341MD";
sensor = <&cam1>;
};
};
pwm9: dmtimer-pwm {
compatible = "ti,omap-dmtimer-pwm";
#pwm-cells = <3>;
......@@ -164,6 +173,31 @@ vctcxo: vctcxo {
};
};
&isp {
vdds_csib-supply = <&vaux2>;
pinctrl-names = "default";
pinctrl-0 = <&camera_pins>;
ports {
port@1 {
reg = <1>;
csi_isp: endpoint {
remote-endpoint = <&csi_cam1>;
bus-type = <3>; /* CCP2 */
clock-lanes = <1>;
data-lanes = <0>;
lane-polarity = <0 0>;
clock-inv = <0>;
/* Select strobe = <1> for back camera, <0> for front camera */
strobe = <1>;
crc = <0>;
};
};
};
};
&omap3_pmx_core {
pinctrl-names = "default";
......@@ -328,6 +362,22 @@ modem_pins: pinmux_modem {
OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* gpio 157 => cmt_bsi */
>;
};
camera_pins: pinmux_camera {
pinctrl-single,pins = <
OMAP3_CORE1_IOPAD(0x210c, PIN_OUTPUT | MUX_MODE7) /* cam_hs */
OMAP3_CORE1_IOPAD(0x210e, PIN_OUTPUT | MUX_MODE7) /* cam_vs */
OMAP3_CORE1_IOPAD(0x2110, PIN_OUTPUT | MUX_MODE0) /* cam_xclka */
OMAP3_CORE1_IOPAD(0x211e, PIN_OUTPUT | MUX_MODE7) /* cam_d4 */
OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE0) /* cam_d6 */
OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE0) /* cam_d7 */
OMAP3_CORE1_IOPAD(0x2126, PIN_INPUT | MUX_MODE0) /* cam_d8 */
OMAP3_CORE1_IOPAD(0x2128, PIN_INPUT | MUX_MODE0) /* cam_d9 */
OMAP3_CORE1_IOPAD(0x212a, PIN_OUTPUT | MUX_MODE7) /* cam_d10 */
OMAP3_CORE1_IOPAD(0x212e, PIN_OUTPUT | MUX_MODE7) /* cam_xclkb */
OMAP3_CORE1_IOPAD(0x2132, PIN_OUTPUT | MUX_MODE0) /* cam_strobe */
>;
};
};
&i2c1 {
......@@ -726,6 +776,40 @@ lis302dl: lis3lv02d@1d {
st,max-limit-y = <32>;
st,max-limit-z = <32>;
};
cam1: camera@3e {
compatible = "toshiba,et8ek8";
reg = <0x3e>;
vana-supply = <&vaux4>;
clocks = <&isp 0>;
clock-names = "extclk";
clock-frequency = <9600000>;
reset-gpio = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */
port {
csi_cam1: endpoint {
bus-type = <3>; /* CCP2 */
strobe = <1>;
clock-inv = <0>;
crc = <1>;
remote-endpoint = <&csi_isp>;
};
};
};
/* D/A converter for auto-focus */
ad5820: dac@0c {
compatible = "adi,ad5820";
reg = <0x0c>;
VANA-supply = <&vaux4>;
#io-channel-cells = <0>;
};
};
&mmc1 {
......@@ -733,6 +817,9 @@ &mmc1 {
pinctrl-0 = <&mmc1_pins>;
vmmc-supply = <&vmmc1>;
bus-width = <4>;
/* For debugging, it is often good idea to remove this GPIO.
It means you can remove back cover (to reboot by removing
battery) and still use the MMC card. */
cd-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* 160 */
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment