Commit d51da4d4 authored by Archit Taneja's avatar Archit Taneja Committed by Vinod Koul

dmaengine: qcom_bam_dma: Add support for BAM v1.7.0

Add register offset table entry for the newer (v1.7.0) version of the BAM IP
found on MSM8916. Update the DT bindings documentation.
Signed-off-by: default avatarArchit Taneja <architt@codeaurora.org>
Tested-by: default avatarIvan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: default avatarVinod Koul <vinod.koul@intel.com>
parent b2607227
......@@ -4,6 +4,7 @@ Required properties:
- compatible: must be one of the following:
* "qcom,bam-v1.4.0" for MSM8974, APQ8074 and APQ8084
* "qcom,bam-v1.3.0" for APQ8064, IPQ8064 and MSM8960
* "qcom,bam-v1.7.0" for MSM8916
- reg: Address range for DMA registers
- interrupts: Should contain the one interrupt shared by all channels
- #dma-cells: must be <1>, the cell in the dmas property of the client device
......
......@@ -171,6 +171,35 @@ static const struct reg_offset_data bam_v1_4_reg_info[] = {
[BAM_P_FIFO_SIZES] = { 0x1820, 0x00, 0x1000, 0x00 },
};
static const struct reg_offset_data bam_v1_7_reg_info[] = {
[BAM_CTRL] = { 0x00000, 0x00, 0x00, 0x00 },
[BAM_REVISION] = { 0x01000, 0x00, 0x00, 0x00 },
[BAM_NUM_PIPES] = { 0x01008, 0x00, 0x00, 0x00 },
[BAM_DESC_CNT_TRSHLD] = { 0x00008, 0x00, 0x00, 0x00 },
[BAM_IRQ_SRCS] = { 0x03010, 0x00, 0x00, 0x00 },
[BAM_IRQ_SRCS_MSK] = { 0x03014, 0x00, 0x00, 0x00 },
[BAM_IRQ_SRCS_UNMASKED] = { 0x03018, 0x00, 0x00, 0x00 },
[BAM_IRQ_STTS] = { 0x00014, 0x00, 0x00, 0x00 },
[BAM_IRQ_CLR] = { 0x00018, 0x00, 0x00, 0x00 },
[BAM_IRQ_EN] = { 0x0001C, 0x00, 0x00, 0x00 },
[BAM_CNFG_BITS] = { 0x0007C, 0x00, 0x00, 0x00 },
[BAM_IRQ_SRCS_EE] = { 0x03000, 0x00, 0x00, 0x1000 },
[BAM_IRQ_SRCS_MSK_EE] = { 0x03004, 0x00, 0x00, 0x1000 },
[BAM_P_CTRL] = { 0x13000, 0x1000, 0x00, 0x00 },
[BAM_P_RST] = { 0x13004, 0x1000, 0x00, 0x00 },
[BAM_P_HALT] = { 0x13008, 0x1000, 0x00, 0x00 },
[BAM_P_IRQ_STTS] = { 0x13010, 0x1000, 0x00, 0x00 },
[BAM_P_IRQ_CLR] = { 0x13014, 0x1000, 0x00, 0x00 },
[BAM_P_IRQ_EN] = { 0x13018, 0x1000, 0x00, 0x00 },
[BAM_P_EVNT_DEST_ADDR] = { 0x1382C, 0x00, 0x1000, 0x00 },
[BAM_P_EVNT_REG] = { 0x13818, 0x00, 0x1000, 0x00 },
[BAM_P_SW_OFSTS] = { 0x13800, 0x00, 0x1000, 0x00 },
[BAM_P_DATA_FIFO_ADDR] = { 0x13824, 0x00, 0x1000, 0x00 },
[BAM_P_DESC_FIFO_ADDR] = { 0x1381C, 0x00, 0x1000, 0x00 },
[BAM_P_EVNT_GEN_TRSHLD] = { 0x13828, 0x00, 0x1000, 0x00 },
[BAM_P_FIFO_SIZES] = { 0x13820, 0x00, 0x1000, 0x00 },
};
/* BAM CTRL */
#define BAM_SW_RST BIT(0)
#define BAM_EN BIT(1)
......@@ -1051,6 +1080,7 @@ static void bam_channel_init(struct bam_device *bdev, struct bam_chan *bchan,
static const struct of_device_id bam_of_match[] = {
{ .compatible = "qcom,bam-v1.3.0", .data = &bam_v1_3_reg_info },
{ .compatible = "qcom,bam-v1.4.0", .data = &bam_v1_4_reg_info },
{ .compatible = "qcom,bam-v1.7.0", .data = &bam_v1_7_reg_info },
{}
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment