Commit d9893d13 authored by David S. Miller's avatar David S. Miller

Merge tag 'nfc-next-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next

Samuel Ortiz says:

====================
NFC 4.3 pull request

This is the NFC pull request for 4.3.
With this one we have:

- A new driver for Samsung's S3FWRN5 NFC chipset. In order to
  properly support this driver, a few NCI core routines needed
  to be exported. Future drivers like Intel's Fields Peak will
  benefit from this.

- SPI support as a physical transport for STM st21nfcb.

- An additional netlink API for sending replies back to userspace
  from vendor commands.

- 2 small fixes for TI's trf7970a

- A few st-nci fixes.
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parents 751a587a 29e76924
* Samsung S3FWRN5 NCI NFC Controller
Required properties:
- compatible: Should be "samsung,s3fwrn5-i2c".
- reg: address on the bus
- interrupt-parent: phandle for the interrupt gpio controller
- interrupts: GPIO interrupt to which the chip is connected
- s3fwrn5,en-gpios: Output GPIO pin used for enabling/disabling the chip
- s3fwrn5,fw-gpios: Output GPIO pin used to enter firmware mode and
sleep/wakeup control
Example:
&hsi2c_4 {
status = "okay";
s3fwrn5@27 {
compatible = "samsung,s3fwrn5-i2c";
reg = <0x27>;
interrupt-parent = <&gpa1>;
interrupts = <3 0 0>;
s3fwrn5,en-gpios = <&gpf1 4 0>;
s3fwrn5,fw-gpios = <&gpj0 2 0>;
};
};
* STMicroelectronics SAS. ST NCI NFC Controller
Required properties:
- compatible: Should be "st,st21nfcb-spi"
- spi-max-frequency: Maximum SPI frequency (<= 10000000).
- interrupt-parent: phandle for the interrupt gpio controller
- interrupts: GPIO interrupt to which the chip is connected
- reset-gpios: Output GPIO pin used to reset the ST21NFCB
Optional SoC Specific Properties:
- pinctrl-names: Contains only one value - "default".
- pintctrl-0: Specifies the pin control groups used for this controller.
Example (for ARM-based BeagleBoard xM with ST21NFCB on SPI4):
&mcspi4 {
status = "okay";
st21nfcb: st21nfcb@0 {
compatible = "st,st21nfcb-spi";
clock-frequency = <4000000>;
interrupt-parent = <&gpio5>;
interrupts = <2 IRQ_TYPE_EDGE_RISING>;
reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>;
};
};
......@@ -8881,6 +8881,12 @@ L: linux-media@vger.kernel.org
S: Supported
F: drivers/media/i2c/s5k5baf.c
SAMSUNG S3FWRN5 NFC DRIVER
M: Robert Baldyga <r.baldyga@samsung.com>
L: linux-nfc@lists.01.org (moderated for non-subscribers)
S: Supported
F: drivers/nfc/s3fwrn5
SAMSUNG SOC CLOCK DRIVERS
M: Sylwester Nawrocki <s.nawrocki@samsung.com>
M: Tomasz Figa <tomasz.figa@gmail.com>
......
......@@ -74,4 +74,5 @@ source "drivers/nfc/nfcmrvl/Kconfig"
source "drivers/nfc/st21nfca/Kconfig"
source "drivers/nfc/st-nci/Kconfig"
source "drivers/nfc/nxp-nci/Kconfig"
source "drivers/nfc/s3fwrn5/Kconfig"
endmenu
......@@ -14,3 +14,4 @@ obj-$(CONFIG_NFC_TRF7970A) += trf7970a.o
obj-$(CONFIG_NFC_ST21NFCA) += st21nfca/
obj-$(CONFIG_NFC_ST_NCI) += st-nci/
obj-$(CONFIG_NFC_NXP_NCI) += nxp-nci/
obj-$(CONFIG_NFC_S3FWRN5) += s3fwrn5/
config NFC_S3FWRN5
tristate
---help---
Core driver for Samsung S3FWRN5 NFC chip. Contains core utilities
of chip. It's intended to be used by PHYs to avoid duplicating lots
of common code.
config NFC_S3FWRN5_I2C
tristate "Samsung S3FWRN5 I2C support"
depends on NFC_NCI && I2C
select NFC_S3FWRN5
default n
---help---
This module adds support for an I2C interface to the S3FWRN5 chip.
Select this if your platform is using the I2C bus.
To compile this driver as a module, choose m here. The module will
be called s3fwrn5_i2c.ko.
Say N if unsure.
#
# Makefile for Samsung S3FWRN5 NFC driver
#
s3fwrn5-objs = core.o firmware.o nci.o
s3fwrn5_i2c-objs = i2c.o
obj-$(CONFIG_NFC_S3FWRN5) += s3fwrn5.o
obj-$(CONFIG_NFC_S3FWRN5_I2C) += s3fwrn5_i2c.o
ccflags-$(CONFIG_NFC_DEBUG) := -DDEBUG
/*
* NCI based driver for Samsung S3FWRN5 NFC chip
*
* Copyright (C) 2015 Samsung Electrnoics
* Robert Baldyga <r.baldyga@samsung.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2 or later, as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, see <http://www.gnu.org/licenses/>.
*/
#include <linux/module.h>
#include <net/nfc/nci_core.h>
#include "s3fwrn5.h"
#include "firmware.h"
#include "nci.h"
#define S3FWRN5_NFC_PROTOCOLS (NFC_PROTO_JEWEL_MASK | \
NFC_PROTO_MIFARE_MASK | \
NFC_PROTO_FELICA_MASK | \
NFC_PROTO_ISO14443_MASK | \
NFC_PROTO_ISO14443_B_MASK | \
NFC_PROTO_ISO15693_MASK)
static int s3fwrn5_firmware_update(struct s3fwrn5_info *info)
{
bool need_update;
int ret;
s3fwrn5_fw_init(&info->fw_info, "sec_s3fwrn5_firmware.bin");
/* Update firmware */
s3fwrn5_set_wake(info, false);
s3fwrn5_set_mode(info, S3FWRN5_MODE_FW);
ret = s3fwrn5_fw_setup(&info->fw_info);
if (ret < 0)
return ret;
need_update = s3fwrn5_fw_check_version(&info->fw_info,
info->ndev->manufact_specific_info);
if (!need_update)
goto out;
dev_info(&info->ndev->nfc_dev->dev, "Detected new firmware version\n");
ret = s3fwrn5_fw_download(&info->fw_info);
if (ret < 0)
goto out;
/* Update RF configuration */
s3fwrn5_set_mode(info, S3FWRN5_MODE_NCI);
s3fwrn5_set_wake(info, true);
ret = s3fwrn5_nci_rf_configure(info, "sec_s3fwrn5_rfreg.bin");
s3fwrn5_set_wake(info, false);
out:
s3fwrn5_set_mode(info, S3FWRN5_MODE_COLD);
s3fwrn5_fw_cleanup(&info->fw_info);
return ret;
}
static int s3fwrn5_nci_open(struct nci_dev *ndev)
{
struct s3fwrn5_info *info = nci_get_drvdata(ndev);
if (s3fwrn5_get_mode(info) != S3FWRN5_MODE_COLD)
return -EBUSY;
s3fwrn5_set_mode(info, S3FWRN5_MODE_NCI);
s3fwrn5_set_wake(info, true);
return 0;
}
static int s3fwrn5_nci_close(struct nci_dev *ndev)
{
struct s3fwrn5_info *info = nci_get_drvdata(ndev);
s3fwrn5_set_wake(info, false);
s3fwrn5_set_mode(info, S3FWRN5_MODE_COLD);
return 0;
}
static int s3fwrn5_nci_send(struct nci_dev *ndev, struct sk_buff *skb)
{
struct s3fwrn5_info *info = nci_get_drvdata(ndev);
int ret;
mutex_lock(&info->mutex);
if (s3fwrn5_get_mode(info) != S3FWRN5_MODE_NCI) {
mutex_unlock(&info->mutex);
return -EINVAL;
}
ret = s3fwrn5_write(info, skb);
if (ret < 0)
kfree_skb(skb);
mutex_unlock(&info->mutex);
return ret;
}
static int s3fwrn5_nci_post_setup(struct nci_dev *ndev)
{
struct s3fwrn5_info *info = nci_get_drvdata(ndev);
int ret;
ret = s3fwrn5_firmware_update(info);
if (ret < 0)
goto out;
/* NCI core reset */
s3fwrn5_set_mode(info, S3FWRN5_MODE_NCI);
s3fwrn5_set_wake(info, true);
ret = nci_core_reset(info->ndev);
if (ret < 0)
goto out;
ret = nci_core_init(info->ndev);
out:
return ret;
}
static struct nci_ops s3fwrn5_nci_ops = {
.open = s3fwrn5_nci_open,
.close = s3fwrn5_nci_close,
.send = s3fwrn5_nci_send,
.post_setup = s3fwrn5_nci_post_setup,
};
int s3fwrn5_probe(struct nci_dev **ndev, void *phy_id, struct device *pdev,
struct s3fwrn5_phy_ops *phy_ops, unsigned int max_payload)
{
struct s3fwrn5_info *info;
int ret;
info = devm_kzalloc(pdev, sizeof(*info), GFP_KERNEL);
if (!info)
return -ENOMEM;
info->phy_id = phy_id;
info->pdev = pdev;
info->phy_ops = phy_ops;
info->max_payload = max_payload;
mutex_init(&info->mutex);
s3fwrn5_set_mode(info, S3FWRN5_MODE_COLD);
s3fwrn5_nci_get_prop_ops(&s3fwrn5_nci_ops.prop_ops,
&s3fwrn5_nci_ops.n_prop_ops);
info->ndev = nci_allocate_device(&s3fwrn5_nci_ops,
S3FWRN5_NFC_PROTOCOLS, 0, 0);
if (!info->ndev)
return -ENOMEM;
nci_set_parent_dev(info->ndev, pdev);
nci_set_drvdata(info->ndev, info);
ret = nci_register_device(info->ndev);
if (ret < 0) {
nci_free_device(info->ndev);
return ret;
}
info->fw_info.ndev = info->ndev;
*ndev = info->ndev;
return ret;
}
EXPORT_SYMBOL(s3fwrn5_probe);
void s3fwrn5_remove(struct nci_dev *ndev)
{
struct s3fwrn5_info *info = nci_get_drvdata(ndev);
s3fwrn5_set_mode(info, S3FWRN5_MODE_COLD);
nci_unregister_device(ndev);
nci_free_device(ndev);
}
EXPORT_SYMBOL(s3fwrn5_remove);
int s3fwrn5_recv_frame(struct nci_dev *ndev, struct sk_buff *skb,
enum s3fwrn5_mode mode)
{
switch (mode) {
case S3FWRN5_MODE_NCI:
return nci_recv_frame(ndev, skb);
case S3FWRN5_MODE_FW:
return s3fwrn5_fw_recv_frame(ndev, skb);
default:
return -ENODEV;
}
}
EXPORT_SYMBOL(s3fwrn5_recv_frame);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Samsung S3FWRN5 NFC driver");
MODULE_AUTHOR("Robert Baldyga <r.baldyga@samsung.com>");
This diff is collapsed.
/*
* NCI based driver for Samsung S3FWRN5 NFC chip
*
* Copyright (C) 2015 Samsung Electrnoics
* Robert Baldyga <r.baldyga@samsung.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2 or later, as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, see <http://www.gnu.org/licenses/>.
*/
#ifndef __LOCAL_S3FWRN5_FIRMWARE_H_
#define __LOCAL_S3FWRN5_FIRMWARE_H_
/* FW Message Types */
#define S3FWRN5_FW_MSG_CMD 0x00
#define S3FWRN5_FW_MSG_RSP 0x01
#define S3FWRN5_FW_MSG_DATA 0x02
/* FW Return Codes */
#define S3FWRN5_FW_RET_SUCCESS 0x00
#define S3FWRN5_FW_RET_MESSAGE_TYPE_INVALID 0x01
#define S3FWRN5_FW_RET_COMMAND_INVALID 0x02
#define S3FWRN5_FW_RET_PAGE_DATA_OVERFLOW 0x03
#define S3FWRN5_FW_RET_SECT_DATA_OVERFLOW 0x04
#define S3FWRN5_FW_RET_AUTHENTICATION_FAIL 0x05
#define S3FWRN5_FW_RET_FLASH_OPERATION_FAIL 0x06
#define S3FWRN5_FW_RET_ADDRESS_OUT_OF_RANGE 0x07
#define S3FWRN5_FW_RET_PARAMETER_INVALID 0x08
/* ---- FW Packet structures ---- */
#define S3FWRN5_FW_HDR_SIZE 4
struct s3fwrn5_fw_header {
__u8 type;
__u8 code;
__u16 len;
};
#define S3FWRN5_FW_CMD_RESET 0x00
#define S3FWRN5_FW_CMD_GET_BOOTINFO 0x01
struct s3fwrn5_fw_cmd_get_bootinfo_rsp {
__u8 hw_version[4];
__u16 sector_size;
__u16 page_size;
__u16 frame_max_size;
__u16 hw_buffer_size;
};
#define S3FWRN5_FW_CMD_ENTER_UPDATE_MODE 0x02
struct s3fwrn5_fw_cmd_enter_updatemode {
__u16 hashcode_size;
__u16 signature_size;
};
#define S3FWRN5_FW_CMD_UPDATE_SECTOR 0x04
struct s3fwrn5_fw_cmd_update_sector {
__u32 base_address;
};
#define S3FWRN5_FW_CMD_COMPLETE_UPDATE_MODE 0x05
struct s3fwrn5_fw_image {
const struct firmware *fw;
char date[13];
u32 version;
const void *sig;
u32 sig_size;
const void *image;
u32 image_sectors;
const void *custom_sig;
u32 custom_sig_size;
};
struct s3fwrn5_fw_info {
struct nci_dev *ndev;
struct s3fwrn5_fw_image fw;
char fw_name[NFC_FIRMWARE_NAME_MAXSIZE + 1];
const void *sig;
u32 sig_size;
u32 sector_size;
u32 base_addr;
struct completion completion;
struct sk_buff *rsp;
char parity;
};
void s3fwrn5_fw_init(struct s3fwrn5_fw_info *fw_info, const char *fw_name);
int s3fwrn5_fw_setup(struct s3fwrn5_fw_info *fw_info);
bool s3fwrn5_fw_check_version(struct s3fwrn5_fw_info *fw_info, u32 version);
int s3fwrn5_fw_download(struct s3fwrn5_fw_info *fw_info);
void s3fwrn5_fw_cleanup(struct s3fwrn5_fw_info *fw_info);
int s3fwrn5_fw_recv_frame(struct nci_dev *ndev, struct sk_buff *skb);
#endif /* __LOCAL_S3FWRN5_FIRMWARE_H_ */
/*
* I2C Link Layer for Samsung S3FWRN5 NCI based Driver
*
* Copyright (C) 2015 Samsung Electrnoics
* Robert Baldyga <r.baldyga@samsung.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2 or later, as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, see <http://www.gnu.org/licenses/>.
*/
#include <linux/i2c.h>
#include <linux/gpio.h>
#include <linux/delay.h>
#include <linux/of_gpio.h>
#include <linux/of_irq.h>
#include <linux/module.h>
#include <net/nfc/nfc.h>
#include "s3fwrn5.h"
#define S3FWRN5_I2C_DRIVER_NAME "s3fwrn5_i2c"
#define S3FWRN5_I2C_MAX_PAYLOAD 32
#define S3FWRN5_EN_WAIT_TIME 150
struct s3fwrn5_i2c_phy {
struct i2c_client *i2c_dev;
struct nci_dev *ndev;
unsigned int gpio_en;
unsigned int gpio_fw_wake;
struct mutex mutex;
enum s3fwrn5_mode mode;
unsigned int irq_skip:1;
};
static void s3fwrn5_i2c_set_wake(void *phy_id, bool wake)
{
struct s3fwrn5_i2c_phy *phy = phy_id;
mutex_lock(&phy->mutex);
gpio_set_value(phy->gpio_fw_wake, wake);
msleep(S3FWRN5_EN_WAIT_TIME/2);
mutex_unlock(&phy->mutex);
}
static void s3fwrn5_i2c_set_mode(void *phy_id, enum s3fwrn5_mode mode)
{
struct s3fwrn5_i2c_phy *phy = phy_id;
mutex_lock(&phy->mutex);
if (phy->mode == mode)
goto out;
phy->mode = mode;
gpio_set_value(phy->gpio_en, 1);
gpio_set_value(phy->gpio_fw_wake, 0);
if (mode == S3FWRN5_MODE_FW)
gpio_set_value(phy->gpio_fw_wake, 1);
if (mode != S3FWRN5_MODE_COLD) {
msleep(S3FWRN5_EN_WAIT_TIME);
gpio_set_value(phy->gpio_en, 0);
msleep(S3FWRN5_EN_WAIT_TIME/2);
}
phy->irq_skip = true;
out:
mutex_unlock(&phy->mutex);
}
static enum s3fwrn5_mode s3fwrn5_i2c_get_mode(void *phy_id)
{
struct s3fwrn5_i2c_phy *phy = phy_id;
enum s3fwrn5_mode mode;
mutex_lock(&phy->mutex);
mode = phy->mode;
mutex_unlock(&phy->mutex);
return mode;
}
static int s3fwrn5_i2c_write(void *phy_id, struct sk_buff *skb)
{
struct s3fwrn5_i2c_phy *phy = phy_id;
int ret;
mutex_lock(&phy->mutex);
phy->irq_skip = false;
ret = i2c_master_send(phy->i2c_dev, skb->data, skb->len);
if (ret == -EREMOTEIO) {
/* Retry, chip was in standby */
usleep_range(110000, 120000);
ret = i2c_master_send(phy->i2c_dev, skb->data, skb->len);
}
mutex_unlock(&phy->mutex);
if (ret < 0)
return ret;
if (ret != skb->len)
return -EREMOTEIO;
return 0;
}
static struct s3fwrn5_phy_ops i2c_phy_ops = {
.set_wake = s3fwrn5_i2c_set_wake,
.set_mode = s3fwrn5_i2c_set_mode,
.get_mode = s3fwrn5_i2c_get_mode,
.write = s3fwrn5_i2c_write,
};
static int s3fwrn5_i2c_read(struct s3fwrn5_i2c_phy *phy)
{
struct sk_buff *skb;
size_t hdr_size;
size_t data_len;
char hdr[4];
int ret;
hdr_size = (phy->mode == S3FWRN5_MODE_NCI) ?
NCI_CTRL_HDR_SIZE : S3FWRN5_FW_HDR_SIZE;
ret = i2c_master_recv(phy->i2c_dev, hdr, hdr_size);
if (ret < 0)
return ret;
if (ret < hdr_size)
return -EBADMSG;
data_len = (phy->mode == S3FWRN5_MODE_NCI) ?
((struct nci_ctrl_hdr *)hdr)->plen :
((struct s3fwrn5_fw_header *)hdr)->len;
skb = alloc_skb(hdr_size + data_len, GFP_KERNEL);
if (!skb)
return -ENOMEM;
memcpy(skb_put(skb, hdr_size), hdr, hdr_size);
if (data_len == 0)
goto out;
ret = i2c_master_recv(phy->i2c_dev, skb_put(skb, data_len), data_len);
if (ret != data_len) {
kfree_skb(skb);
return -EBADMSG;
}
out:
return s3fwrn5_recv_frame(phy->ndev, skb, phy->mode);
}
static irqreturn_t s3fwrn5_i2c_irq_thread_fn(int irq, void *phy_id)
{
struct s3fwrn5_i2c_phy *phy = phy_id;
int ret = 0;
if (!phy || !phy->ndev) {
WARN_ON_ONCE(1);
return IRQ_NONE;
}
mutex_lock(&phy->mutex);
if (phy->irq_skip)
goto out;
switch (phy->mode) {
case S3FWRN5_MODE_NCI:
case S3FWRN5_MODE_FW:
ret = s3fwrn5_i2c_read(phy);
break;
case S3FWRN5_MODE_COLD:
ret = -EREMOTEIO;
break;
}
out:
mutex_unlock(&phy->mutex);
return IRQ_HANDLED;
}
static int s3fwrn5_i2c_parse_dt(struct i2c_client *client)
{
struct s3fwrn5_i2c_phy *phy = i2c_get_clientdata(client);
struct device_node *np = client->dev.of_node;
if (!np)
return -ENODEV;
phy->gpio_en = of_get_named_gpio(np, "s3fwrn5,en-gpios", 0);
if (!gpio_is_valid(phy->gpio_en))
return -ENODEV;
phy->gpio_fw_wake = of_get_named_gpio(np, "s3fwrn5,fw-gpios", 0);
if (!gpio_is_valid(phy->gpio_fw_wake))
return -ENODEV;
return 0;
}
static int s3fwrn5_i2c_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct s3fwrn5_i2c_phy *phy;
int ret;
phy = devm_kzalloc(&client->dev, sizeof(*phy), GFP_KERNEL);
if (!phy)
return -ENOMEM;
mutex_init(&phy->mutex);
phy->mode = S3FWRN5_MODE_COLD;
phy->irq_skip = true;
phy->i2c_dev = client;
i2c_set_clientdata(client, phy);
ret = s3fwrn5_i2c_parse_dt(client);
if (ret < 0)
return ret;
ret = devm_gpio_request_one(&phy->i2c_dev->dev, phy->gpio_en,
GPIOF_OUT_INIT_HIGH, "s3fwrn5_en");
if (ret < 0)
return ret;
ret = devm_gpio_request_one(&phy->i2c_dev->dev, phy->gpio_fw_wake,
GPIOF_OUT_INIT_LOW, "s3fwrn5_fw_wake");
if (ret < 0)
return ret;
ret = s3fwrn5_probe(&phy->ndev, phy, &phy->i2c_dev->dev, &i2c_phy_ops,
S3FWRN5_I2C_MAX_PAYLOAD);
if (ret < 0)
return ret;
ret = request_threaded_irq(phy->i2c_dev->irq, NULL,
s3fwrn5_i2c_irq_thread_fn, IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
S3FWRN5_I2C_DRIVER_NAME, phy);
if (ret)
s3fwrn5_remove(phy->ndev);
return ret;
}
static int s3fwrn5_i2c_remove(struct i2c_client *client)
{
struct s3fwrn5_i2c_phy *phy = i2c_get_clientdata(client);
s3fwrn5_remove(phy->ndev);
return 0;
}
static struct i2c_device_id s3fwrn5_i2c_id_table[] = {
{S3FWRN5_I2C_DRIVER_NAME, 0},
{}
};
MODULE_DEVICE_TABLE(i2c, s3fwrn5_i2c_id_table);
static const struct of_device_id of_s3fwrn5_i2c_match[] = {
{ .compatible = "samsung,s3fwrn5-i2c", },
{}
};
MODULE_DEVICE_TABLE(of, of_s3fwrn5_i2c_match);
static struct i2c_driver s3fwrn5_i2c_driver = {
.driver = {
.owner = THIS_MODULE,
.name = S3FWRN5_I2C_DRIVER_NAME,
.of_match_table = of_match_ptr(of_s3fwrn5_i2c_match),
},
.probe = s3fwrn5_i2c_probe,
.remove = s3fwrn5_i2c_remove,
.id_table = s3fwrn5_i2c_id_table,
};
module_i2c_driver(s3fwrn5_i2c_driver);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("I2C driver for Samsung S3FWRN5");
MODULE_AUTHOR("Robert Baldyga <r.baldyga@samsung.com>");
/*
* NCI based driver for Samsung S3FWRN5 NFC chip
*
* Copyright (C) 2015 Samsung Electrnoics
* Robert Baldyga <r.baldyga@samsung.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2 or later, as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, see <http://www.gnu.org/licenses/>.
*/
#include <linux/completion.h>
#include <linux/firmware.h>
#include "s3fwrn5.h"
#include "nci.h"
static int s3fwrn5_nci_prop_rsp(struct nci_dev *ndev, struct sk_buff *skb)
{
__u8 status = skb->data[0];
nci_req_complete(ndev, status);
return 0;
}
static struct nci_prop_ops s3fwrn5_nci_prop_ops[] = {
{
.opcode = nci_opcode_pack(NCI_GID_PROPRIETARY,
NCI_PROP_AGAIN),
.rsp = s3fwrn5_nci_prop_rsp,
},
{
.opcode = nci_opcode_pack(NCI_GID_PROPRIETARY,
NCI_PROP_GET_RFREG),
.rsp = s3fwrn5_nci_prop_rsp,
},
{
.opcode = nci_opcode_pack(NCI_GID_PROPRIETARY,
NCI_PROP_SET_RFREG),
.rsp = s3fwrn5_nci_prop_rsp,
},
{
.opcode = nci_opcode_pack(NCI_GID_PROPRIETARY,
NCI_PROP_GET_RFREG_VER),
.rsp = s3fwrn5_nci_prop_rsp,
},
{
.opcode = nci_opcode_pack(NCI_GID_PROPRIETARY,
NCI_PROP_SET_RFREG_VER),
.rsp = s3fwrn5_nci_prop_rsp,
},
{
.opcode = nci_opcode_pack(NCI_GID_PROPRIETARY,
NCI_PROP_START_RFREG),
.rsp = s3fwrn5_nci_prop_rsp,
},
{
.opcode = nci_opcode_pack(NCI_GID_PROPRIETARY,
NCI_PROP_STOP_RFREG),
.rsp = s3fwrn5_nci_prop_rsp,
},
{
.opcode = nci_opcode_pack(NCI_GID_PROPRIETARY,
NCI_PROP_FW_CFG),
.rsp = s3fwrn5_nci_prop_rsp,
},
{
.opcode = nci_opcode_pack(NCI_GID_PROPRIETARY,
NCI_PROP_WR_RESET),
.rsp = s3fwrn5_nci_prop_rsp,
},
};
void s3fwrn5_nci_get_prop_ops(struct nci_prop_ops **ops, size_t *n)
{
*ops = s3fwrn5_nci_prop_ops;
*n = ARRAY_SIZE(s3fwrn5_nci_prop_ops);
}
#define S3FWRN5_RFREG_SECTION_SIZE 252
int s3fwrn5_nci_rf_configure(struct s3fwrn5_info *info, const char *fw_name)
{
const struct firmware *fw;
struct nci_prop_fw_cfg_cmd fw_cfg;
struct nci_prop_set_rfreg_cmd set_rfreg;
struct nci_prop_stop_rfreg_cmd stop_rfreg;
u32 checksum;
int i, len;
int ret;
ret = request_firmware(&fw, fw_name, &info->ndev->nfc_dev->dev);
if (ret < 0)
return ret;
/* Compute rfreg checksum */
checksum = 0;
for (i = 0; i < fw->size; i += 4)
checksum += *((u32 *)(fw->data+i));
/* Set default clock configuration for external crystal */
fw_cfg.clk_type = 0x01;
fw_cfg.clk_speed = 0xff;
fw_cfg.clk_req = 0xff;
ret = nci_prop_cmd(info->ndev, NCI_PROP_FW_CFG,
sizeof(fw_cfg), (__u8 *)&fw_cfg);
if (ret < 0)
goto out;
/* Start rfreg configuration */
dev_info(&info->ndev->nfc_dev->dev,
"rfreg configuration update: %s\n", fw_name);
ret = nci_prop_cmd(info->ndev, NCI_PROP_START_RFREG, 0, NULL);
if (ret < 0) {
dev_err(&info->ndev->nfc_dev->dev,
"Unable to start rfreg update\n");
goto out;
}
/* Update rfreg */
set_rfreg.index = 0;
for (i = 0; i < fw->size; i += S3FWRN5_RFREG_SECTION_SIZE) {
len = (fw->size - i < S3FWRN5_RFREG_SECTION_SIZE) ?
(fw->size - i) : S3FWRN5_RFREG_SECTION_SIZE;
memcpy(set_rfreg.data, fw->data+i, len);
ret = nci_prop_cmd(info->ndev, NCI_PROP_SET_RFREG,
len+1, (__u8 *)&set_rfreg);
if (ret < 0) {
dev_err(&info->ndev->nfc_dev->dev,
"rfreg update error (code=%d)\n", ret);
goto out;
}
set_rfreg.index++;
}
/* Finish rfreg configuration */
stop_rfreg.checksum = checksum & 0xffff;
ret = nci_prop_cmd(info->ndev, NCI_PROP_STOP_RFREG,
sizeof(stop_rfreg), (__u8 *)&stop_rfreg);
if (ret < 0) {
dev_err(&info->ndev->nfc_dev->dev,
"Unable to stop rfreg update\n");
goto out;
}
dev_info(&info->ndev->nfc_dev->dev,
"rfreg configuration update: success\n");
out:
release_firmware(fw);
return ret;
}
/*
* NCI based driver for Samsung S3FWRN5 NFC chip
*
* Copyright (C) 2015 Samsung Electrnoics
* Robert Baldyga <r.baldyga@samsung.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2 or later, as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, see <http://www.gnu.org/licenses/>.
*/
#ifndef __LOCAL_S3FWRN5_NCI_H_
#define __LOCAL_S3FWRN5_NCI_H_
#include "s3fwrn5.h"
#define NCI_PROP_AGAIN 0x01
#define NCI_PROP_GET_RFREG 0x21
#define NCI_PROP_SET_RFREG 0x22
struct nci_prop_set_rfreg_cmd {
__u8 index;
__u8 data[252];
};
struct nci_prop_set_rfreg_rsp {
__u8 status;
};
#define NCI_PROP_GET_RFREG_VER 0x24
struct nci_prop_get_rfreg_ver_rsp {
__u8 status;
__u8 data[8];
};
#define NCI_PROP_SET_RFREG_VER 0x25
struct nci_prop_set_rfreg_ver_cmd {
__u8 data[8];
};
struct nci_prop_set_rfreg_ver_rsp {
__u8 status;
};
#define NCI_PROP_START_RFREG 0x26
struct nci_prop_start_rfreg_rsp {
__u8 status;
};
#define NCI_PROP_STOP_RFREG 0x27
struct nci_prop_stop_rfreg_cmd {
__u16 checksum;
};
struct nci_prop_stop_rfreg_rsp {
__u8 status;
};
#define NCI_PROP_FW_CFG 0x28
struct nci_prop_fw_cfg_cmd {
__u8 clk_type;
__u8 clk_speed;
__u8 clk_req;
};
struct nci_prop_fw_cfg_rsp {
__u8 status;
};
#define NCI_PROP_WR_RESET 0x2f
void s3fwrn5_nci_get_prop_ops(struct nci_prop_ops **ops, size_t *n);
int s3fwrn5_nci_rf_configure(struct s3fwrn5_info *info, const char *fw_name);
#endif /* __LOCAL_S3FWRN5_NCI_H_ */
/*
* NCI based driver for Samsung S3FWRN5 NFC chip
*
* Copyright (C) 2015 Samsung Electrnoics
* Robert Baldyga <r.baldyga@samsung.com>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2 or later, as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, see <http://www.gnu.org/licenses/>.
*/
#ifndef __LOCAL_S3FWRN5_H_
#define __LOCAL_S3FWRN5_H_
#include <linux/nfc.h>
#include <net/nfc/nci_core.h>
#include "firmware.h"
enum s3fwrn5_mode {
S3FWRN5_MODE_COLD,
S3FWRN5_MODE_NCI,
S3FWRN5_MODE_FW,
};
struct s3fwrn5_phy_ops {
void (*set_wake)(void *id, bool sleep);
void (*set_mode)(void *id, enum s3fwrn5_mode);
enum s3fwrn5_mode (*get_mode)(void *id);
int (*write)(void *id, struct sk_buff *skb);
};
struct s3fwrn5_info {
struct nci_dev *ndev;
void *phy_id;
struct device *pdev;
struct s3fwrn5_phy_ops *phy_ops;
unsigned int max_payload;
struct s3fwrn5_fw_info fw_info;
struct mutex mutex;
};
static inline int s3fwrn5_set_mode(struct s3fwrn5_info *info,
enum s3fwrn5_mode mode)
{
if (!info->phy_ops->set_mode)
return -ENOTSUPP;
info->phy_ops->set_mode(info->phy_id, mode);
return 0;
}
static inline enum s3fwrn5_mode s3fwrn5_get_mode(struct s3fwrn5_info *info)
{
if (!info->phy_ops->get_mode)
return -ENOTSUPP;
return info->phy_ops->get_mode(info->phy_id);
}
static inline int s3fwrn5_set_wake(struct s3fwrn5_info *info, bool wake)
{
if (!info->phy_ops->set_wake)
return -ENOTSUPP;
info->phy_ops->set_wake(info->phy_id, wake);
return 0;
}
static inline int s3fwrn5_write(struct s3fwrn5_info *info, struct sk_buff *skb)
{
if (!info->phy_ops->write)
return -ENOTSUPP;
return info->phy_ops->write(info->phy_id, skb);
}
int s3fwrn5_probe(struct nci_dev **ndev, void *phy_id, struct device *pdev,
struct s3fwrn5_phy_ops *phy_ops, unsigned int max_payload);
void s3fwrn5_remove(struct nci_dev *ndev);
int s3fwrn5_recv_frame(struct nci_dev *ndev, struct sk_buff *skb,
enum s3fwrn5_mode mode);
#endif /* __LOCAL_S3FWRN5_H_ */
......@@ -21,3 +21,14 @@ config NFC_ST_NCI_I2C
If you choose to build a module, it'll be called st-nci_i2c.
Say N if unsure.
config NFC_ST_NCI_SPI
tristate "NFC ST NCI spi support"
depends on NFC_ST_NCI && SPI
---help---
This module adds support for an SPI interface to the
STMicroelectronics NFC NCI chips familly.
Select this if your platform is using the spi bus.
If you choose to build a module, it'll be called st-nci_spi.
Say N if unsure.
......@@ -7,3 +7,6 @@ obj-$(CONFIG_NFC_ST_NCI) += st-nci.o
st-nci_i2c-objs = i2c.o
obj-$(CONFIG_NFC_ST_NCI_I2C) += st-nci_i2c.o
st-nci_spi-objs = spi.o
obj-$(CONFIG_NFC_ST_NCI_SPI) += st-nci_spi.o
......@@ -25,15 +25,15 @@
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/nfc.h>
#include <linux/platform_data/st_nci.h>
#include <linux/platform_data/st-nci.h>
#include "ndlc.h"
#define DRIVER_DESC "NCI NFC driver for ST21NFCB"
#define DRIVER_DESC "NCI NFC driver for ST_NCI"
/* ndlc header */
#define ST21NFCB_FRAME_HEADROOM 1
#define ST21NFCB_FRAME_TAILROOM 0
#define ST_NCI_FRAME_HEADROOM 1
#define ST_NCI_FRAME_TAILROOM 0
#define ST_NCI_I2C_MIN_SIZE 4 /* PCB(1) + NCI Packet header(3) */
#define ST_NCI_I2C_MAX_SIZE 250 /* req 4.2.1 */
......@@ -118,15 +118,10 @@ static int st_nci_i2c_write(void *phy_id, struct sk_buff *skb)
/*
* Reads an ndlc frame and returns it in a newly allocated sk_buff.
* returns:
* frame size : if received frame is complete (find ST21NFCB_SOF_EOF at
* end of read)
* -EAGAIN : if received frame is incomplete (not find ST21NFCB_SOF_EOF
* at end of read)
* 0 : if received frame is complete
* -EREMOTEIO : i2c read error (fatal)
* -EBADMSG : frame was incorrect and discarded
* (value returned from st_nci_i2c_repack)
* -EIO : if no ST21NFCB_SOF_EOF is found after reaching
* the read length end sequence
* -ENOMEM : cannot allocate skb, frame dropped
*/
static int st_nci_i2c_read(struct st_nci_i2c_phy *phy,
struct sk_buff **skb)
......@@ -179,7 +174,7 @@ static int st_nci_i2c_read(struct st_nci_i2c_phy *phy,
/*
* Reads an ndlc frame from the chip.
*
* On ST21NFCB, IRQ goes in idle state when read starts.
* On ST_NCI, IRQ goes in idle state when read starts.
*/
static irqreturn_t st_nci_irq_thread_fn(int irq, void *phy_id)
{
......@@ -325,12 +320,12 @@ static int st_nci_i2c_probe(struct i2c_client *client,
}
} else {
nfc_err(&client->dev,
"st21nfcb platform resources not available\n");
"st_nci platform resources not available\n");
return -ENODEV;
}
r = ndlc_probe(phy, &i2c_phy_ops, &client->dev,
ST21NFCB_FRAME_HEADROOM, ST21NFCB_FRAME_TAILROOM,
ST_NCI_FRAME_HEADROOM, ST_NCI_FRAME_TAILROOM,
&phy->ndlc);
if (r < 0) {
nfc_err(&client->dev, "Unable to register ndlc layer\n");
......
......@@ -171,6 +171,8 @@ static void llt_ndlc_rcv_queue(struct llt_ndlc *ndlc)
if ((pcb & PCB_TYPE_MASK) == PCB_TYPE_SUPERVISOR) {
switch (pcb & PCB_SYNC_MASK) {
case PCB_SYNC_ACK:
skb = skb_dequeue(&ndlc->ack_pending_q);
kfree_skb(skb);
del_timer_sync(&ndlc->t1_timer);
del_timer_sync(&ndlc->t2_timer);
ndlc->t2_active = false;
......@@ -192,12 +194,13 @@ static void llt_ndlc_rcv_queue(struct llt_ndlc *ndlc)
msecs_to_jiffies(NDLC_TIMER_T1_WAIT));
break;
default:
pr_err("UNKNOWN Packet Control Byte=%d\n", pcb);
kfree_skb(skb);
break;
}
} else {
} else if ((pcb & PCB_TYPE_MASK) == PCB_TYPE_DATAFRAME) {
nci_recv_frame(ndlc->ndev, skb);
} else {
kfree_skb(skb);
}
}
}
......
/*
* SPI Link Layer for ST NCI based Driver
* Copyright (C) 2014-2015 STMicroelectronics SAS. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2, as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, see <http://www.gnu.org/licenses/>.
*/
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/module.h>
#include <linux/spi/spi.h>
#include <linux/gpio.h>
#include <linux/of_irq.h>
#include <linux/of_gpio.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/nfc.h>
#include <linux/platform_data/st-nci.h>
#include "ndlc.h"
#define DRIVER_DESC "NCI NFC driver for ST_NCI"
/* ndlc header */
#define ST_NCI_FRAME_HEADROOM 1
#define ST_NCI_FRAME_TAILROOM 0
#define ST_NCI_SPI_MIN_SIZE 4 /* PCB(1) + NCI Packet header(3) */
#define ST_NCI_SPI_MAX_SIZE 250 /* req 4.2.1 */
#define ST_NCI_SPI_DRIVER_NAME "st_nci_spi"
static struct spi_device_id st_nci_spi_id_table[] = {
{ST_NCI_SPI_DRIVER_NAME, 0},
{}
};
MODULE_DEVICE_TABLE(spi, st_nci_spi_id_table);
struct st_nci_spi_phy {
struct spi_device *spi_dev;
struct llt_ndlc *ndlc;
unsigned int gpio_reset;
unsigned int irq_polarity;
};
#define SPI_DUMP_SKB(info, skb) \
do { \
pr_debug("%s:\n", info); \
print_hex_dump(KERN_DEBUG, "spi: ", DUMP_PREFIX_OFFSET, \
16, 1, (skb)->data, (skb)->len, 0); \
} while (0)
static int st_nci_spi_enable(void *phy_id)
{
struct st_nci_spi_phy *phy = phy_id;
gpio_set_value(phy->gpio_reset, 0);
usleep_range(10000, 15000);
gpio_set_value(phy->gpio_reset, 1);
usleep_range(80000, 85000);
if (phy->ndlc->powered == 0)
enable_irq(phy->spi_dev->irq);
return 0;
}
static void st_nci_spi_disable(void *phy_id)
{
struct st_nci_spi_phy *phy = phy_id;
disable_irq_nosync(phy->spi_dev->irq);
}
/*
* Writing a frame must not return the number of written bytes.
* It must return either zero for success, or <0 for error.
* In addition, it must not alter the skb
*/
static int st_nci_spi_write(void *phy_id, struct sk_buff *skb)
{
int r;
struct st_nci_spi_phy *phy = phy_id;
struct spi_device *dev = phy->spi_dev;
struct sk_buff *skb_rx;
u8 buf[ST_NCI_SPI_MAX_SIZE];
struct spi_transfer spi_xfer = {
.tx_buf = skb->data,
.rx_buf = buf,
.len = skb->len,
};
SPI_DUMP_SKB("st_nci_spi_write", skb);
if (phy->ndlc->hard_fault != 0)
return phy->ndlc->hard_fault;
r = spi_sync_transfer(dev, &spi_xfer, 1);
/*
* We may have received some valuable data on miso line.
* Send them back in the ndlc state machine.
*/
if (!r) {
skb_rx = alloc_skb(skb->len, GFP_KERNEL);
if (!skb_rx) {
r = -ENOMEM;
goto exit;
}
skb_put(skb_rx, skb->len);
memcpy(skb_rx->data, buf, skb->len);
ndlc_recv(phy->ndlc, skb_rx);
}
exit:
return r;
}
/*
* Reads an ndlc frame and returns it in a newly allocated sk_buff.
* returns:
* 0 : if received frame is complete
* -EREMOTEIO : i2c read error (fatal)
* -EBADMSG : frame was incorrect and discarded
* -ENOMEM : cannot allocate skb, frame dropped
*/
static int st_nci_spi_read(struct st_nci_spi_phy *phy,
struct sk_buff **skb)
{
int r;
u8 len;
u8 buf[ST_NCI_SPI_MAX_SIZE];
struct spi_device *dev = phy->spi_dev;
struct spi_transfer spi_xfer = {
.rx_buf = buf,
.len = ST_NCI_SPI_MIN_SIZE,
};
r = spi_sync_transfer(dev, &spi_xfer, 1);
if (r < 0)
return -EREMOTEIO;
len = be16_to_cpu(*(__be16 *) (buf + 2));
if (len > ST_NCI_SPI_MAX_SIZE) {
nfc_err(&dev->dev, "invalid frame len\n");
phy->ndlc->hard_fault = 1;
return -EBADMSG;
}
*skb = alloc_skb(ST_NCI_SPI_MIN_SIZE + len, GFP_KERNEL);
if (*skb == NULL)
return -ENOMEM;
skb_reserve(*skb, ST_NCI_SPI_MIN_SIZE);
skb_put(*skb, ST_NCI_SPI_MIN_SIZE);
memcpy((*skb)->data, buf, ST_NCI_SPI_MIN_SIZE);
if (!len)
return 0;
spi_xfer.len = len;
r = spi_sync_transfer(dev, &spi_xfer, 1);
if (r < 0) {
kfree_skb(*skb);
return -EREMOTEIO;
}
skb_put(*skb, len);
memcpy((*skb)->data + ST_NCI_SPI_MIN_SIZE, buf, len);
SPI_DUMP_SKB("spi frame read", *skb);
return 0;
}
/*
* Reads an ndlc frame from the chip.
*
* On ST21NFCB, IRQ goes in idle state when read starts.
*/
static irqreturn_t st_nci_irq_thread_fn(int irq, void *phy_id)
{
struct st_nci_spi_phy *phy = phy_id;
struct spi_device *dev;
struct sk_buff *skb = NULL;
int r;
if (!phy || !phy->ndlc || irq != phy->spi_dev->irq) {
WARN_ON_ONCE(1);
return IRQ_NONE;
}
dev = phy->spi_dev;
dev_dbg(&dev->dev, "IRQ\n");
if (phy->ndlc->hard_fault)
return IRQ_HANDLED;
if (!phy->ndlc->powered) {
st_nci_spi_disable(phy);
return IRQ_HANDLED;
}
r = st_nci_spi_read(phy, &skb);
if (r == -EREMOTEIO || r == -ENOMEM || r == -EBADMSG)
return IRQ_HANDLED;
ndlc_recv(phy->ndlc, skb);
return IRQ_HANDLED;
}
static struct nfc_phy_ops spi_phy_ops = {
.write = st_nci_spi_write,
.enable = st_nci_spi_enable,
.disable = st_nci_spi_disable,
};
#ifdef CONFIG_OF
static int st_nci_spi_of_request_resources(struct spi_device *dev)
{
struct st_nci_spi_phy *phy = spi_get_drvdata(dev);
struct device_node *pp;
int gpio;
int r;
pp = dev->dev.of_node;
if (!pp)
return -ENODEV;
/* Get GPIO from device tree */
gpio = of_get_named_gpio(pp, "reset-gpios", 0);
if (gpio < 0) {
nfc_err(&dev->dev,
"Failed to retrieve reset-gpios from device tree\n");
return gpio;
}
/* GPIO request and configuration */
r = devm_gpio_request_one(&dev->dev, gpio,
GPIOF_OUT_INIT_HIGH, "clf_reset");
if (r) {
nfc_err(&dev->dev, "Failed to request reset pin\n");
return r;
}
phy->gpio_reset = gpio;
phy->irq_polarity = irq_get_trigger_type(dev->irq);
return 0;
}
#else
static int st_nci_spi_of_request_resources(struct spi_device *dev)
{
return -ENODEV;
}
#endif
static int st_nci_spi_request_resources(struct spi_device *dev)
{
struct st_nci_nfc_platform_data *pdata;
struct st_nci_spi_phy *phy = spi_get_drvdata(dev);
int r;
pdata = dev->dev.platform_data;
if (pdata == NULL) {
nfc_err(&dev->dev, "No platform data\n");
return -EINVAL;
}
/* store for later use */
phy->gpio_reset = pdata->gpio_reset;
phy->irq_polarity = pdata->irq_polarity;
r = devm_gpio_request_one(&dev->dev,
phy->gpio_reset, GPIOF_OUT_INIT_HIGH, "clf_reset");
if (r) {
pr_err("%s : reset gpio_request failed\n", __FILE__);
return r;
}
return 0;
}
static int st_nci_spi_probe(struct spi_device *dev)
{
struct st_nci_spi_phy *phy;
struct st_nci_nfc_platform_data *pdata;
int r;
dev_dbg(&dev->dev, "%s\n", __func__);
dev_dbg(&dev->dev, "IRQ: %d\n", dev->irq);
/* Check SPI platform functionnalities */
if (!dev) {
pr_debug("%s: dev is NULL. Device is not accessible.\n",
__func__);
return -ENODEV;
}
phy = devm_kzalloc(&dev->dev, sizeof(struct st_nci_spi_phy),
GFP_KERNEL);
if (!phy)
return -ENOMEM;
phy->spi_dev = dev;
spi_set_drvdata(dev, phy);
pdata = dev->dev.platform_data;
if (!pdata && dev->dev.of_node) {
r = st_nci_spi_of_request_resources(dev);
if (r) {
nfc_err(&dev->dev, "No platform data\n");
return r;
}
} else if (pdata) {
r = st_nci_spi_request_resources(dev);
if (r) {
nfc_err(&dev->dev,
"Cannot get platform resources\n");
return r;
}
} else {
nfc_err(&dev->dev,
"st_nci platform resources not available\n");
return -ENODEV;
}
r = ndlc_probe(phy, &spi_phy_ops, &dev->dev,
ST_NCI_FRAME_HEADROOM, ST_NCI_FRAME_TAILROOM,
&phy->ndlc);
if (r < 0) {
nfc_err(&dev->dev, "Unable to register ndlc layer\n");
return r;
}
r = devm_request_threaded_irq(&dev->dev, dev->irq, NULL,
st_nci_irq_thread_fn,
phy->irq_polarity | IRQF_ONESHOT,
ST_NCI_SPI_DRIVER_NAME, phy);
if (r < 0)
nfc_err(&dev->dev, "Unable to register IRQ handler\n");
return r;
}
static int st_nci_spi_remove(struct spi_device *dev)
{
struct st_nci_spi_phy *phy = spi_get_drvdata(dev);
dev_dbg(&dev->dev, "%s\n", __func__);
ndlc_remove(phy->ndlc);
return 0;
}
#ifdef CONFIG_OF
static const struct of_device_id of_st_nci_spi_match[] = {
{ .compatible = "st,st21nfcb-spi", },
{}
};
MODULE_DEVICE_TABLE(of, of_st_nci_spi_match);
#endif
static struct spi_driver st_nci_spi_driver = {
.driver = {
.owner = THIS_MODULE,
.name = ST_NCI_SPI_DRIVER_NAME,
.of_match_table = of_match_ptr(of_st_nci_spi_match),
},
.probe = st_nci_spi_probe,
.id_table = st_nci_spi_id_table,
.remove = st_nci_spi_remove,
};
module_spi_driver(st_nci_spi_driver);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION(DRIVER_DESC);
......@@ -189,14 +189,14 @@ int st_nci_hci_load_session(struct nci_dev *ndev)
ST_NCI_DEVICE_MGNT_GATE,
ST_NCI_DEVICE_MGNT_PIPE);
if (r < 0)
goto free_info;
return r;
/* Get pipe list */
r = nci_hci_send_cmd(ndev, ST_NCI_DEVICE_MGNT_GATE,
ST_NCI_DM_GETINFO, pipe_list, sizeof(pipe_list),
&skb_pipe_list);
if (r < 0)
goto free_info;
return r;
/* Complete the existing gate_pipe table */
for (i = 0; i < skb_pipe_list->len; i++) {
......@@ -222,6 +222,7 @@ int st_nci_hci_load_session(struct nci_dev *ndev)
dm_pipe_info->src_host_id != ST_NCI_ESE_HOST_ID) {
pr_err("Unexpected apdu_reader pipe on host %x\n",
dm_pipe_info->src_host_id);
kfree_skb(skb_pipe_info);
continue;
}
......@@ -241,13 +242,12 @@ int st_nci_hci_load_session(struct nci_dev *ndev)
ndev->hci_dev->pipes[st_nci_gates[j].pipe].host =
dm_pipe_info->src_host_id;
}
kfree_skb(skb_pipe_info);
}
memcpy(ndev->hci_dev->init_data.gates, st_nci_gates,
sizeof(st_nci_gates));
free_info:
kfree_skb(skb_pipe_info);
kfree_skb(skb_pipe_list);
return r;
}
......
......@@ -148,14 +148,14 @@ static int st21nfca_hci_load_session(struct nfc_hci_dev *hdev)
ST21NFCA_DEVICE_MGNT_GATE,
ST21NFCA_DEVICE_MGNT_PIPE);
if (r < 0)
goto free_info;
return r;
/* Get pipe list */
r = nfc_hci_send_cmd(hdev, ST21NFCA_DEVICE_MGNT_GATE,
ST21NFCA_DM_GETINFO, pipe_list, sizeof(pipe_list),
&skb_pipe_list);
if (r < 0)
goto free_info;
return r;
/* Complete the existing gate_pipe table */
for (i = 0; i < skb_pipe_list->len; i++) {
......@@ -181,6 +181,7 @@ static int st21nfca_hci_load_session(struct nfc_hci_dev *hdev)
info->src_host_id != ST21NFCA_ESE_HOST_ID) {
pr_err("Unexpected apdu_reader pipe on host %x\n",
info->src_host_id);
kfree_skb(skb_pipe_info);
continue;
}
......@@ -200,6 +201,7 @@ static int st21nfca_hci_load_session(struct nfc_hci_dev *hdev)
hdev->pipes[st21nfca_gates[j].pipe].dest_host =
info->src_host_id;
}
kfree_skb(skb_pipe_info);
}
/*
......@@ -214,13 +216,12 @@ static int st21nfca_hci_load_session(struct nfc_hci_dev *hdev)
st21nfca_gates[i].gate,
st21nfca_gates[i].pipe);
if (r < 0)
goto free_info;
goto free_list;
}
}
memcpy(hdev->init_data.gates, st21nfca_gates, sizeof(st21nfca_gates));
free_info:
kfree_skb(skb_pipe_info);
free_list:
kfree_skb(skb_pipe_list);
return r;
}
......
......@@ -336,7 +336,7 @@
#define TRF7970A_NFC_TARGET_LEVEL_RFDET(v) ((v) & 0x07)
#define TRF7970A_NFC_TARGET_LEVEL_HI_RF BIT(3)
#define TRF7970A_NFC_TARGET_LEVEL_SDD_EN BIT(3)
#define TRF7970A_NFC_TARGET_LEVEL_SDD_EN BIT(5)
#define TRF7970A_NFC_TARGET_LEVEL_LD_S_4BYTES (0x0 << 6)
#define TRF7970A_NFC_TARGET_LEVEL_LD_S_7BYTES (0x1 << 6)
#define TRF7970A_NFC_TARGET_LEVEL_LD_S_10BYTES (0x2 << 6)
......@@ -629,7 +629,9 @@ static void trf7970a_send_upstream(struct trf7970a *trf)
}
if (trf->adjust_resp_len) {
skb_trim(trf->rx_skb, trf->rx_skb->len - 1);
if (trf->rx_skb)
skb_trim(trf->rx_skb, trf->rx_skb->len - 1);
trf->adjust_resp_len = false;
}
......
/*
* Driver include for ST NCI NFC chip family.
*
* Copyright (C) 2014-2015 STMicroelectronics SAS. All rights reserved.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms and conditions of the GNU General Public License,
* version 2, as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, see <http://www.gnu.org/licenses/>.
*/
#ifndef _ST_NCI_H_
#define _ST_NCI_H_
#define ST_NCI_DRIVER_NAME "st_nci"
struct st_nci_nfc_platform_data {
unsigned int gpio_reset;
unsigned int irq_polarity;
};
#endif /* _ST_NCI_H_ */
......@@ -79,6 +79,7 @@ struct nci_ops {
int (*close)(struct nci_dev *ndev);
int (*send)(struct nci_dev *ndev, struct sk_buff *skb);
int (*setup)(struct nci_dev *ndev);
int (*post_setup)(struct nci_dev *ndev);
int (*fw_download)(struct nci_dev *ndev, const char *firmware_name);
__u32 (*get_rfprotocol)(struct nci_dev *ndev, __u8 rf_protocol);
int (*discover_se)(struct nci_dev *ndev);
......@@ -277,6 +278,8 @@ int nci_request(struct nci_dev *ndev,
unsigned long opt),
unsigned long opt, __u32 timeout);
int nci_prop_cmd(struct nci_dev *ndev, __u8 oid, size_t len, __u8 *payload);
int nci_core_reset(struct nci_dev *ndev);
int nci_core_init(struct nci_dev *ndev);
int nci_recv_frame(struct nci_dev *ndev, struct sk_buff *skb);
int nci_set_config(struct nci_dev *ndev, __u8 id, size_t len, __u8 *val);
......
......@@ -203,6 +203,7 @@ struct nfc_dev {
int n_vendor_cmds;
struct nfc_ops *ops;
struct genl_info *cur_cmd_info;
};
#define to_nfc_dev(_dev) container_of(_dev, struct nfc_dev, dev)
......@@ -318,4 +319,44 @@ static inline int nfc_set_vendor_cmds(struct nfc_dev *dev,
return 0;
}
struct sk_buff *__nfc_alloc_vendor_cmd_reply_skb(struct nfc_dev *dev,
enum nfc_attrs attr,
u32 oui, u32 subcmd,
int approxlen);
int nfc_vendor_cmd_reply(struct sk_buff *skb);
/**
* nfc_vendor_cmd_alloc_reply_skb - allocate vendor command reply
* @dev: nfc device
* @oui: vendor oui
* @approxlen: an upper bound of the length of the data that will
* be put into the skb
*
* This function allocates and pre-fills an skb for a reply to
* a vendor command. Since it is intended for a reply, calling
* it outside of a vendor command's doit() operation is invalid.
*
* The returned skb is pre-filled with some identifying data in
* a way that any data that is put into the skb (with skb_put(),
* nla_put() or similar) will end up being within the
* %NFC_ATTR_VENDOR_DATA attribute, so all that needs to be done
* with the skb is adding data for the corresponding userspace tool
* which can then read that data out of the vendor data attribute.
* You must not modify the skb in any other way.
*
* When done, call nfc_vendor_cmd_reply() with the skb and return
* its error code as the result of the doit() operation.
*
* Return: An allocated and pre-filled skb. %NULL if any errors happen.
*/
static inline struct sk_buff *
nfc_vendor_cmd_alloc_reply_skb(struct nfc_dev *dev,
u32 oui, u32 subcmd, int approxlen)
{
return __nfc_alloc_vendor_cmd_reply_skb(dev,
NFC_ATTR_VENDOR_DATA,
oui,
subcmd, approxlen);
}
#endif /* __NET_NFC_H */
......@@ -351,6 +351,20 @@ int nci_prop_cmd(struct nci_dev *ndev, __u8 oid, size_t len, __u8 *payload)
}
EXPORT_SYMBOL(nci_prop_cmd);
int nci_core_reset(struct nci_dev *ndev)
{
return __nci_request(ndev, nci_reset_req, 0,
msecs_to_jiffies(NCI_RESET_TIMEOUT));
}
EXPORT_SYMBOL(nci_core_reset);
int nci_core_init(struct nci_dev *ndev)
{
return __nci_request(ndev, nci_init_req, 0,
msecs_to_jiffies(NCI_INIT_TIMEOUT));
}
EXPORT_SYMBOL(nci_core_init);
static int nci_open_device(struct nci_dev *ndev)
{
int rc = 0;
......@@ -388,6 +402,10 @@ static int nci_open_device(struct nci_dev *ndev)
msecs_to_jiffies(NCI_INIT_TIMEOUT));
}
if (ndev->ops->post_setup) {
rc = ndev->ops->post_setup(ndev);
}
if (!rc) {
rc = __nci_request(ndev, nci_init_complete_req, 0,
msecs_to_jiffies(NCI_INIT_TIMEOUT));
......
......@@ -233,7 +233,7 @@ int nci_hci_send_cmd(struct nci_dev *ndev, u8 gate, u8 cmd,
r = nci_request(ndev, nci_hci_send_data_req, (unsigned long)&data,
msecs_to_jiffies(NCI_DATA_TIMEOUT));
if (r == NCI_STATUS_OK)
if (r == NCI_STATUS_OK && skb)
*skb = conn_info->rx_skb;
return r;
......
......@@ -63,6 +63,8 @@ static const struct nla_policy nfc_genl_policy[NFC_ATTR_MAX + 1] = {
[NFC_ATTR_FIRMWARE_NAME] = { .type = NLA_STRING,
.len = NFC_FIRMWARE_NAME_MAXSIZE },
[NFC_ATTR_SE_APDU] = { .type = NLA_BINARY },
[NFC_ATTR_VENDOR_DATA] = { .type = NLA_BINARY },
};
static const struct nla_policy nfc_sdp_genl_policy[NFC_SDP_ATTR_MAX + 1] = {
......@@ -1503,7 +1505,7 @@ static int nfc_genl_vendor_cmd(struct sk_buff *skb,
u32 dev_idx, vid, subcmd;
u8 *data;
size_t data_len;
int i;
int i, err;
if (!info->attrs[NFC_ATTR_DEVICE_INDEX] ||
!info->attrs[NFC_ATTR_VENDOR_ID] ||
......@@ -1518,12 +1520,13 @@ static int nfc_genl_vendor_cmd(struct sk_buff *skb,
if (!dev || !dev->vendor_cmds || !dev->n_vendor_cmds)
return -ENODEV;
data = nla_data(info->attrs[NFC_ATTR_VENDOR_DATA]);
if (data) {
if (info->attrs[NFC_ATTR_VENDOR_DATA]) {
data = nla_data(info->attrs[NFC_ATTR_VENDOR_DATA]);
data_len = nla_len(info->attrs[NFC_ATTR_VENDOR_DATA]);
if (data_len == 0)
return -EINVAL;
} else {
data = NULL;
data_len = 0;
}
......@@ -1533,12 +1536,92 @@ static int nfc_genl_vendor_cmd(struct sk_buff *skb,
if (cmd->vendor_id != vid || cmd->subcmd != subcmd)
continue;
return cmd->doit(dev, data, data_len);
dev->cur_cmd_info = info;
err = cmd->doit(dev, data, data_len);
dev->cur_cmd_info = NULL;
return err;
}
return -EOPNOTSUPP;
}
/* message building helper */
static inline void *nfc_hdr_put(struct sk_buff *skb, u32 portid, u32 seq,
int flags, u8 cmd)
{
/* since there is no private header just add the generic one */
return genlmsg_put(skb, portid, seq, &nfc_genl_family, flags, cmd);
}
static struct sk_buff *
__nfc_alloc_vendor_cmd_skb(struct nfc_dev *dev, int approxlen,
u32 portid, u32 seq,
enum nfc_attrs attr,
u32 oui, u32 subcmd, gfp_t gfp)
{
struct sk_buff *skb;
void *hdr;
skb = nlmsg_new(approxlen + 100, gfp);
if (!skb)
return NULL;
hdr = nfc_hdr_put(skb, portid, seq, 0, NFC_CMD_VENDOR);
if (!hdr) {
kfree_skb(skb);
return NULL;
}
if (nla_put_u32(skb, NFC_ATTR_DEVICE_INDEX, dev->idx))
goto nla_put_failure;
if (nla_put_u32(skb, NFC_ATTR_VENDOR_ID, oui))
goto nla_put_failure;
if (nla_put_u32(skb, NFC_ATTR_VENDOR_SUBCMD, subcmd))
goto nla_put_failure;
((void **)skb->cb)[0] = dev;
((void **)skb->cb)[1] = hdr;
return skb;
nla_put_failure:
kfree_skb(skb);
return NULL;
}
struct sk_buff *__nfc_alloc_vendor_cmd_reply_skb(struct nfc_dev *dev,
enum nfc_attrs attr,
u32 oui, u32 subcmd,
int approxlen)
{
if (WARN_ON(!dev->cur_cmd_info))
return NULL;
return __nfc_alloc_vendor_cmd_skb(dev, approxlen,
dev->cur_cmd_info->snd_portid,
dev->cur_cmd_info->snd_seq, attr,
oui, subcmd, GFP_KERNEL);
}
EXPORT_SYMBOL(__nfc_alloc_vendor_cmd_reply_skb);
int nfc_vendor_cmd_reply(struct sk_buff *skb)
{
struct nfc_dev *dev = ((void **)skb->cb)[0];
void *hdr = ((void **)skb->cb)[1];
/* clear CB data for netlink core to own from now on */
memset(skb->cb, 0, sizeof(skb->cb));
if (WARN_ON(!dev->cur_cmd_info)) {
kfree_skb(skb);
return -EINVAL;
}
genlmsg_end(skb, hdr);
return genlmsg_reply(skb, dev->cur_cmd_info);
}
EXPORT_SYMBOL(nfc_vendor_cmd_reply);
static const struct genl_ops nfc_genl_ops[] = {
{
.cmd = NFC_CMD_GET_DEVICE,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment