bnx2x: Load/Unload under traffic

Load/Unload under traffic
Few issues were found when loading and unloading under traffic:
- When receiving Tx interrupt call netif_wake_queue if the queue is
  stopped but the state is open
- Check that interrupts are enabled before doing anything else on the
  msix_fp_int function
- In nic_load, enable the interrupts only when needed and ready for it
- Function stop_leading returns status since it can fail
- Add 1ms delay when unloading the driver to validate that there are no
  open transactions that already started by the FW
- Splitting the "has work" function into Tx and Rx so the same function
  will be used on unload and interrupts
- Do not request for WoL if only resetting the device (save the time
  that it takes the FW to set the link after reset)
- Fixing the device reset after iSCSI boot and before driver load - all
  internal buffers must be cleared before the driver is loaded
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/bnx2x.h

@@ -274,6 +274,15 @@ struct bnx2x_fastpath {
 
 #define bnx2x_fp(bp, nr, var)		(bp->fp[nr].var)
 
+#define BNX2X_HAS_TX_WORK(fp) \
+			((fp->tx_pkt_prod != le16_to_cpu(*fp->tx_cons_sb)) || \
+			 (fp->tx_pkt_prod != fp->tx_pkt_cons))
+
+#define BNX2X_HAS_RX_WORK(fp) \
+			(fp->rx_comp_cons != le16_to_cpu(*fp->rx_cons_sb))
+
+#define BNX2X_HAS_WORK(fp)	(BNX2X_HAS_RX_WORK(fp) || BNX2X_HAS_TX_WORK(fp))
+
 
 /* MC hsi */
 #define MAX_FETCH_BD			13	/* HW max BDs per packet */

drivers/net/bnx2x_reg.h

@@ -1677,6 +1677,7 @@
 /* [RW 8] init credit counter for port0 in LLH */
 #define NIG_REG_LLH0_XCM_INIT_CREDIT				 0x10554
 #define NIG_REG_LLH0_XCM_MASK					 0x10130
+#define NIG_REG_LLH1_BRB1_DRV_MASK				 0x10248
 /* [RW 1] send to BRB1 if no match on any of RMP rules. */
 #define NIG_REG_LLH1_BRB1_NOT_MCP				 0x102dc
 /* [RW 2] Determine the classification participants. 0: no classification.1:
@@ -4962,6 +4963,7 @@
 #define MISC_REGISTERS_GPIO_PORT_SHIFT				 4
 #define MISC_REGISTERS_GPIO_SET_POS				 8
 #define MISC_REGISTERS_RESET_REG_1_CLEAR			 0x588
+#define MISC_REGISTERS_RESET_REG_1_RST_NIG			 (0x1<<7)
 #define MISC_REGISTERS_RESET_REG_1_SET				 0x584
 #define MISC_REGISTERS_RESET_REG_2_CLEAR			 0x598
 #define MISC_REGISTERS_RESET_REG_2_RST_BMAC0			 (0x1<<0)
@@ -4997,6 +4999,7 @@
 #define HW_LOCK_RESOURCE_8072_MDIO				 0
 #define HW_LOCK_RESOURCE_GPIO					 1
 #define HW_LOCK_RESOURCE_SPIO					 2
+#define HW_LOCK_RESOURCE_UNDI					 5
 #define AEU_INPUTS_ATTN_BITS_BRB_PARITY_ERROR		      (1<<18)
 #define AEU_INPUTS_ATTN_BITS_CCM_HW_INTERRUPT		      (1<<31)
 #define AEU_INPUTS_ATTN_BITS_CDU_HW_INTERRUPT		      (1<<9)