Commit db8668a1 authored by Andrew Lunn's avatar Andrew Lunn Committed by David S. Miller

net: phy: marvell: Configure TDR pulse based on measurement length

When performing a TDR measurement for a short distance, the pulse
width should be low, to help differentiate between the outgoing pulse
and any reflection. For longer distances, the pulse should be wider,
to help with attenuation.
Signed-off-by: default avatarAndrew Lunn <andrew@lunn.ch>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent a618e86d
......@@ -214,6 +214,11 @@
#define MII_VCT5_TX_PULSE_CTRL_MAX_AMP BIT(7)
#define MII_VCT5_TX_PULSE_CTRL_GT_140m_46_86mV (0x6 << 0)
/* For TDR measurements less than 11 meters, a short pulse should be
* used.
*/
#define TDR_SHORT_CABLE_LENGTH 11
#define MII_VCT7_PAIR_0_DISTANCE 0x10
#define MII_VCT7_PAIR_1_DISTANCE 0x11
#define MII_VCT7_PAIR_2_DISTANCE 0x12
......@@ -1835,14 +1840,19 @@ static int marvell_vct5_amplitude_graph(struct phy_device *phydev)
{
struct marvell_priv *priv = phydev->priv;
int distance;
u16 width;
int page;
int err;
u16 reg;
if (priv->first <= TDR_SHORT_CABLE_LENGTH)
width = MII_VCT5_TX_PULSE_CTRL_PULSE_WIDTH_32nS;
else
width = MII_VCT5_TX_PULSE_CTRL_PULSE_WIDTH_128nS;
reg = MII_VCT5_TX_PULSE_CTRL_GT_140m_46_86mV |
MII_VCT5_TX_PULSE_CTRL_DONT_WAIT_LINK_DOWN |
MII_VCT5_TX_PULSE_CTRL_MAX_AMP |
MII_VCT5_TX_PULSE_CTRL_PULSE_WIDTH_32nS;
MII_VCT5_TX_PULSE_CTRL_MAX_AMP | width;
err = phy_write_paged(phydev, MII_MARVELL_VCT5_PAGE,
MII_VCT5_TX_PULSE_CTRL, reg);
......@@ -1866,6 +1876,17 @@ static int marvell_vct5_amplitude_graph(struct phy_device *phydev)
priv->pair);
if (err)
goto restore_page;
if (distance > TDR_SHORT_CABLE_LENGTH &&
width == MII_VCT5_TX_PULSE_CTRL_PULSE_WIDTH_32nS) {
width = MII_VCT5_TX_PULSE_CTRL_PULSE_WIDTH_128nS;
reg = MII_VCT5_TX_PULSE_CTRL_GT_140m_46_86mV |
MII_VCT5_TX_PULSE_CTRL_DONT_WAIT_LINK_DOWN |
MII_VCT5_TX_PULSE_CTRL_MAX_AMP | width;
err = __phy_write(phydev, MII_VCT5_TX_PULSE_CTRL, reg);
if (err)
goto restore_page;
}
}
restore_page:
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment