Commit dc4dc360 authored by Laxman Dewangan's avatar Laxman Dewangan Committed by Mark Brown

spi: tegra: add spi driver for SLINK controller

Tegra20/Tegra30 supports the spi interface through its SLINK
controller. Add spi driver for SLINK controller.
Signed-off-by: default avatarLaxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: default avatarStephen Warren <swarren@nvidia.com>
Signed-off-by: default avatarMark Brown <broonie@opensource.wolfsonmicro.com>
parent 8f0d8163
NVIDIA Tegra20/Tegra30 SLINK controller.
Required properties:
- compatible : should be "nvidia,tegra20-slink", "nvidia,tegra30-slink".
- reg: Should contain SLINK registers location and length.
- interrupts: Should contain SLINK interrupts.
- nvidia,dma-request-selector : The Tegra DMA controller's phandle and
request selector for this SLINK controller.
Recommended properties:
- spi-max-frequency: Definition as per
Documentation/devicetree/bindings/spi/spi-bus.txt
Example:
slink@7000d600 {
compatible = "nvidia,tegra20-slink";
reg = <0x7000d600 0x200>;
interrupts = <0 82 0x04>;
nvidia,dma-request-selector = <&apbdma 16>;
spi-max-frequency = <25000000>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
......@@ -385,6 +385,12 @@ config SPI_MXS
help
SPI driver for Freescale MXS devices.
config SPI_TEGRA20_SLINK
tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
depends on ARCH_TEGRA && TEGRA20_APB_DMA
help
SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
config SPI_TI_SSP
tristate "TI Sequencer Serial Port - SPI Support"
depends on MFD_TI_SSP
......
......@@ -60,10 +60,10 @@ obj-$(CONFIG_SPI_SH_MSIOF) += spi-sh-msiof.o
obj-$(CONFIG_SPI_SH_SCI) += spi-sh-sci.o
obj-$(CONFIG_SPI_SIRF) += spi-sirf.o
obj-$(CONFIG_SPI_STMP3XXX) += spi-stmp.o
obj-$(CONFIG_SPI_TEGRA20_SLINK) += spi-tegra20-slink.o
obj-$(CONFIG_SPI_TI_SSP) += spi-ti-ssp.o
obj-$(CONFIG_SPI_TLE62X0) += spi-tle62x0.o
obj-$(CONFIG_SPI_TOPCLIFF_PCH) += spi-topcliff-pch.o
obj-$(CONFIG_SPI_TXX9) += spi-txx9.o
obj-$(CONFIG_SPI_XCOMM) += spi-xcomm.o
obj-$(CONFIG_SPI_XILINX) += spi-xilinx.o
This diff is collapsed.
/*
* spi-tegra.h: SPI interface for Nvidia Tegra20 SLINK controller.
*
* Copyright (C) 2011 NVIDIA Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
* more details.
*
* You should have received a copy of the GNU General Public License along
* with this program; if not, write to the Free Software Foundation, Inc.,
* 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA.
*/
#ifndef _LINUX_SPI_TEGRA_H
#define _LINUX_SPI_TEGRA_H
struct tegra_spi_platform_data {
int dma_req_sel;
unsigned int spi_max_frequency;
};
/*
* Controller data from device to pass some info like
* hw based chip select can be used or not and if yes
* then CS hold and setup time.
*/
struct tegra_spi_device_controller_data {
bool is_hw_based_cs;
int cs_setup_clk_count;
int cs_hold_clk_count;
};
#endif /* _LINUX_SPI_TEGRA_H */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment