Commit dfe32893 authored by vimal singh's avatar vimal singh Committed by David Woodhouse

mtd: omap: adding DMA mode support in nand prefetch/post-write

This patch adds DMA mode support for nand prefetch/post-write engine.
Signed-off-by: default avatarVimal Singh <vimalsingh@ti.com>
Signed-off-by: default avatarDavid Woodhouse <David.Woodhouse@intel.com>
parent 59e9c5ae
......@@ -88,6 +88,15 @@ config MTD_NAND_OMAP_PREFETCH
The NAND device can be accessed for Read/Write using GPMC PREFETCH engine
to improve the performance.
config MTD_NAND_OMAP_PREFETCH_DMA
depends on MTD_NAND_OMAP_PREFETCH
bool "DMA mode"
default n
help
The GPMC PREFETCH engine can be configured eigther in MPU interrupt mode
or in DMA interrupt mode.
Say y for DMA mode or MPU mode will be used
config MTD_NAND_TS7250
tristate "NAND Flash device on TS-7250 board"
depends on MACH_TS72XX
......
......@@ -18,8 +18,7 @@
#include <linux/mtd/partitions.h>
#include <linux/io.h>
#include <asm/dma.h>
#include <mach/dma.h>
#include <mach/gpmc.h>
#include <mach/nand.h>
......@@ -118,8 +117,19 @@ static int use_prefetch = 1;
/* "modprobe ... use_prefetch=0" etc */
module_param(use_prefetch, bool, 0);
MODULE_PARM_DESC(use_prefetch, "enable/disable use of PREFETCH");
#ifdef CONFIG_MTD_NAND_OMAP_PREFETCH_DMA
static int use_dma = 1;
/* "modprobe ... use_dma=0" etc */
module_param(use_dma, bool, 0);
MODULE_PARM_DESC(use_dma, "enable/disable use of DMA");
#else
const int use_dma;
#endif
#else
const int use_prefetch;
const int use_dma;
#endif
struct omap_nand_info {
......@@ -135,6 +145,8 @@ struct omap_nand_info {
void __iomem *gpmc_cs_baseaddr;
void __iomem *gpmc_baseaddr;
void __iomem *nand_pref_fifo_add;
struct completion comp;
int dma_ch;
};
/**
......@@ -355,6 +367,147 @@ static void omap_write_buf_pref(struct mtd_info *mtd,
}
}
#ifdef CONFIG_MTD_NAND_OMAP_PREFETCH_DMA
/*
* omap_nand_dma_cb: callback on the completion of dma transfer
* @lch: logical channel
* @ch_satuts: channel status
* @data: pointer to completion data structure
*/
static void omap_nand_dma_cb(int lch, u16 ch_status, void *data)
{
complete((struct completion *) data);
}
/*
* omap_nand_dma_transfer: configer and start dma transfer
* @mtd: MTD device structure
* @addr: virtual address in RAM of source/destination
* @len: number of data bytes to be transferred
* @is_write: flag for read/write operation
*/
static inline int omap_nand_dma_transfer(struct mtd_info *mtd, void *addr,
unsigned int len, int is_write)
{
struct omap_nand_info *info = container_of(mtd,
struct omap_nand_info, mtd);
uint32_t prefetch_status = 0;
enum dma_data_direction dir = is_write ? DMA_TO_DEVICE :
DMA_FROM_DEVICE;
dma_addr_t dma_addr;
int ret;
/* The fifo depth is 64 bytes. We have a sync at each frame and frame
* length is 64 bytes.
*/
int buf_len = len >> 6;
if (addr >= high_memory) {
struct page *p1;
if (((size_t)addr & PAGE_MASK) !=
((size_t)(addr + len - 1) & PAGE_MASK))
goto out_copy;
p1 = vmalloc_to_page(addr);
if (!p1)
goto out_copy;
addr = page_address(p1) + ((size_t)addr & ~PAGE_MASK);
}
dma_addr = dma_map_single(&info->pdev->dev, addr, len, dir);
if (dma_mapping_error(&info->pdev->dev, dma_addr)) {
dev_err(&info->pdev->dev,
"Couldn't DMA map a %d byte buffer\n", len);
goto out_copy;
}
if (is_write) {
omap_set_dma_dest_params(info->dma_ch, 0, OMAP_DMA_AMODE_CONSTANT,
info->phys_base, 0, 0);
omap_set_dma_src_params(info->dma_ch, 0, OMAP_DMA_AMODE_POST_INC,
dma_addr, 0, 0);
omap_set_dma_transfer_params(info->dma_ch, OMAP_DMA_DATA_TYPE_S32,
0x10, buf_len, OMAP_DMA_SYNC_FRAME,
OMAP24XX_DMA_GPMC, OMAP_DMA_DST_SYNC);
} else {
omap_set_dma_src_params(info->dma_ch, 0, OMAP_DMA_AMODE_CONSTANT,
info->phys_base, 0, 0);
omap_set_dma_dest_params(info->dma_ch, 0, OMAP_DMA_AMODE_POST_INC,
dma_addr, 0, 0);
omap_set_dma_transfer_params(info->dma_ch, OMAP_DMA_DATA_TYPE_S32,
0x10, buf_len, OMAP_DMA_SYNC_FRAME,
OMAP24XX_DMA_GPMC, OMAP_DMA_SRC_SYNC);
}
/* configure and start prefetch transfer */
ret = gpmc_prefetch_enable(info->gpmc_cs, 0x1, len, is_write);
if (ret)
/* PFPW engine is busy, use cpu copy methode */
goto out_copy;
init_completion(&info->comp);
omap_start_dma(info->dma_ch);
/* setup and start DMA using dma_addr */
wait_for_completion(&info->comp);
while (0x3fff & (prefetch_status = gpmc_prefetch_status()))
;
/* disable and stop the PFPW engine */
gpmc_prefetch_reset();
dma_unmap_single(&info->pdev->dev, dma_addr, len, dir);
return 0;
out_copy:
if (info->nand.options & NAND_BUSWIDTH_16)
is_write == 0 ? omap_read_buf16(mtd, (u_char *) addr, len)
: omap_write_buf16(mtd, (u_char *) addr, len);
else
is_write == 0 ? omap_read_buf8(mtd, (u_char *) addr, len)
: omap_write_buf8(mtd, (u_char *) addr, len);
return 0;
}
#else
static void omap_nand_dma_cb(int lch, u16 ch_status, void *data) {}
static inline int omap_nand_dma_transfer(struct mtd_info *mtd, void *addr,
unsigned int len, int is_write)
{
return 0;
}
#endif
/**
* omap_read_buf_dma_pref - read data from NAND controller into buffer
* @mtd: MTD device structure
* @buf: buffer to store date
* @len: number of bytes to read
*/
static void omap_read_buf_dma_pref(struct mtd_info *mtd, u_char *buf, int len)
{
if (len <= mtd->oobsize)
omap_read_buf_pref(mtd, buf, len);
else
/* start transfer in DMA mode */
omap_nand_dma_transfer(mtd, buf, len, 0x0);
}
/**
* omap_write_buf_dma_pref - write buffer to NAND controller
* @mtd: MTD device structure
* @buf: data buffer
* @len: number of bytes to write
*/
static void omap_write_buf_dma_pref(struct mtd_info *mtd,
const u_char *buf, int len)
{
if (len <= mtd->oobsize)
omap_write_buf_pref(mtd, buf, len);
else
/* start transfer in DMA mode */
omap_nand_dma_transfer(mtd, buf, len, 0x1);
}
/**
* omap_verify_buf - Verify chip data against buffer
* @mtd: MTD device structure
......@@ -821,6 +974,23 @@ static int __devinit omap_nand_probe(struct platform_device *pdev)
info->nand.read_buf = omap_read_buf_pref;
info->nand.write_buf = omap_write_buf_pref;
if (use_dma) {
err = omap_request_dma(OMAP24XX_DMA_GPMC, "NAND",
omap_nand_dma_cb, &info->comp, &info->dma_ch);
if (err < 0) {
info->dma_ch = -1;
printk(KERN_WARNING "DMA request failed."
" Non-dma data transfer mode\n");
} else {
omap_set_dma_dest_burst_mode(info->dma_ch,
OMAP_DMA_DATA_BURST_16);
omap_set_dma_src_burst_mode(info->dma_ch,
OMAP_DMA_DATA_BURST_16);
info->nand.read_buf = omap_read_buf_dma_pref;
info->nand.write_buf = omap_write_buf_dma_pref;
}
}
} else {
if (info->nand.options & NAND_BUSWIDTH_16) {
info->nand.read_buf = omap_read_buf16;
......@@ -887,6 +1057,9 @@ static int omap_nand_remove(struct platform_device *pdev)
struct omap_nand_info *info = mtd->priv;
platform_set_drvdata(pdev, NULL);
if (use_dma)
omap_free_dma(info->dma_ch);
/* Release NAND device, its internal structures and partitions */
nand_release(&info->mtd);
iounmap(info->nand_pref_fifo_add);
......@@ -906,6 +1079,15 @@ static struct platform_driver omap_nand_driver = {
static int __init omap_nand_init(void)
{
printk(KERN_INFO "%s driver initializing\n", DRIVER_NAME);
/* This check is required if driver is being
* loaded run time as a module
*/
if ((1 == use_dma) && (0 == use_prefetch)) {
printk(KERN_INFO"Wrong parameters: 'use_dma' can not be 1 "
"without use_prefetch'. Prefetch will not be"
" used in either mode (mpu or dma)\n");
}
return platform_driver_register(&omap_nand_driver);
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment