net: switch to using PHY_INTERFACE_MODE_10GBASER rather than 10GKR

Switch network drivers, phy drivers, and SFP/phylink over to use the
more correct 10GBASE-R, rather than 10GBASE-KR. 10GBASE-KR is backplane
ethernet, which is 10GBASE-R with autonegotiation on top, which our
current usage on the affected platforms does not have.

The only remaining user of PHY_INTERFACE_MODE_10GKR is the Aquantia
PHY, which has a separate mode for 10GBASE-KR.

For Marvell mvpp2, we detect 10GBASE-KR, and rewrite it to 10GBASE-R
for compatibility with existing DT - this is the only network driver
at present that makes use of PHY_INTERFACE_MODE_10GKR.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c

@@ -1114,7 +1114,7 @@ mvpp2_shared_interrupt_mask_unmask(struct mvpp2_port *port, bool mask)
 /* Port configuration routines */
 static bool mvpp2_is_xlg(phy_interface_t interface)
 {
-	return interface == PHY_INTERFACE_MODE_10GKR ||
+	return interface == PHY_INTERFACE_MODE_10GBASER ||
 	       interface == PHY_INTERFACE_MODE_XAUI;
 }
 
@@ -1200,7 +1200,7 @@ static int mvpp22_gop_init(struct mvpp2_port *port)
 	case PHY_INTERFACE_MODE_2500BASEX:
 		mvpp22_gop_init_sgmii(port);
 		break;
-	case PHY_INTERFACE_MODE_10GKR:
+	case PHY_INTERFACE_MODE_10GBASER:
 		if (port->gop_id != 0)
 			goto invalid_conf;
 		mvpp22_gop_init_10gkr(port);
@@ -1649,7 +1649,7 @@ static void mvpp22_pcs_reset_deassert(struct mvpp2_port *port)
 	xpcs = priv->iface_base + MVPP22_XPCS_BASE(port->gop_id);
 
 	switch (port->phy_interface) {
-	case PHY_INTERFACE_MODE_10GKR:
+	case PHY_INTERFACE_MODE_10GBASER:
 		val = readl(mpcs + MVPP22_MPCS_CLK_RESET);
 		val |= MAC_CLK_RESET_MAC | MAC_CLK_RESET_SD_RX |
 		       MAC_CLK_RESET_SD_TX;
@@ -4758,7 +4758,7 @@ static void mvpp2_phylink_validate(struct phylink_config *config,
 
 	/* Invalid combinations */
 	switch (state->interface) {
-	case PHY_INTERFACE_MODE_10GKR:
+	case PHY_INTERFACE_MODE_10GBASER:
 	case PHY_INTERFACE_MODE_XAUI:
 		if (port->gop_id != 0)
 			goto empty_set;
@@ -4780,7 +4780,7 @@ static void mvpp2_phylink_validate(struct phylink_config *config,
 	phylink_set(mask, Asym_Pause);
 
 	switch (state->interface) {
-	case PHY_INTERFACE_MODE_10GKR:
+	case PHY_INTERFACE_MODE_10GBASER:
 	case PHY_INTERFACE_MODE_XAUI:
 	case PHY_INTERFACE_MODE_NA:
 		if (port->gop_id == 0) {
@@ -5247,6 +5247,15 @@ static int mvpp2_port_probe(struct platform_device *pdev,
 		goto err_free_netdev;
 	}
 
+	/*
+	 * Rewrite 10GBASE-KR to 10GBASE-R for compatibility with existing DT.
+	 * Existing usage of 10GBASE-KR is not correct; no backplane
+	 * negotiation is done, and this driver does not actually support
+	 * 10GBASE-KR.
+	 */
+	if (phy_mode == PHY_INTERFACE_MODE_10GKR)
+		phy_mode = PHY_INTERFACE_MODE_10GBASER;
+
 	if (port_node) {
 		comphy = devm_of_phy_get(&pdev->dev, port_node, NULL);
 		if (IS_ERR(comphy)) {

drivers/net/phy/aquantia_main.c

@@ -358,9 +358,11 @@ static int aqr107_read_status(struct phy_device *phydev)
 
 	switch (FIELD_GET(MDIO_PHYXS_VEND_IF_STATUS_TYPE_MASK, val)) {
 	case MDIO_PHYXS_VEND_IF_STATUS_TYPE_KR:
-	case MDIO_PHYXS_VEND_IF_STATUS_TYPE_XFI:
 		phydev->interface = PHY_INTERFACE_MODE_10GKR;
 		break;
+	case MDIO_PHYXS_VEND_IF_STATUS_TYPE_XFI:
+		phydev->interface = PHY_INTERFACE_MODE_10GBASER;
+		break;
 	case MDIO_PHYXS_VEND_IF_STATUS_TYPE_USXGMII:
 		phydev->interface = PHY_INTERFACE_MODE_USXGMII;
 		break;
@@ -493,7 +495,8 @@ static int aqr107_config_init(struct phy_device *phydev)
 	    phydev->interface != PHY_INTERFACE_MODE_2500BASEX &&
 	    phydev->interface != PHY_INTERFACE_MODE_XGMII &&
 	    phydev->interface != PHY_INTERFACE_MODE_USXGMII &&
-	    phydev->interface != PHY_INTERFACE_MODE_10GKR)
+	    phydev->interface != PHY_INTERFACE_MODE_10GKR &&
+	    phydev->interface != PHY_INTERFACE_MODE_10GBASER)
 		return -ENODEV;
 
 	WARN(phydev->interface == PHY_INTERFACE_MODE_XGMII,

drivers/net/phy/bcm84881.c

@@ -53,7 +53,7 @@ static int bcm84881_config_init(struct phy_device *phydev)
 	switch (phydev->interface) {
 	case PHY_INTERFACE_MODE_SGMII:
 	case PHY_INTERFACE_MODE_2500BASEX:
-	case PHY_INTERFACE_MODE_10GKR:
+	case PHY_INTERFACE_MODE_10GBASER:
 		break;
 	default:
 		return -ENODEV;
@@ -218,7 +218,7 @@ static int bcm84881_read_status(struct phy_device *phydev)
 	if (mode == 1 || mode == 2)
 		phydev->interface = PHY_INTERFACE_MODE_SGMII;
 	else if (mode == 3)
-		phydev->interface = PHY_INTERFACE_MODE_10GKR;
+		phydev->interface = PHY_INTERFACE_MODE_10GBASER;
 	else if (mode == 4)
 		phydev->interface = PHY_INTERFACE_MODE_2500BASEX;
 	switch (mode & 7) {

drivers/net/phy/marvell10g.c

@@ -216,7 +216,7 @@ static int mv3310_sfp_insert(void *upstream, const struct sfp_eeprom_id *id)
 	sfp_parse_support(phydev->sfp_bus, id, support);
 	iface = sfp_select_interface(phydev->sfp_bus, support);
 
-	if (iface != PHY_INTERFACE_MODE_10GKR) {
+	if (iface != PHY_INTERFACE_MODE_10GBASER) {
 		dev_err(&phydev->mdio.dev, "incompatible SFP module inserted\n");
 		return -EINVAL;
 	}
@@ -304,7 +304,7 @@ static int mv3310_config_init(struct phy_device *phydev)
 	    phydev->interface != PHY_INTERFACE_MODE_2500BASEX &&
 	    phydev->interface != PHY_INTERFACE_MODE_XAUI &&
 	    phydev->interface != PHY_INTERFACE_MODE_RXAUI &&
-	    phydev->interface != PHY_INTERFACE_MODE_10GKR)
+	    phydev->interface != PHY_INTERFACE_MODE_10GBASER)
 		return -ENODEV;
 
 	return 0;
@@ -386,16 +386,17 @@ static void mv3310_update_interface(struct phy_device *phydev)
 {
 	if ((phydev->interface == PHY_INTERFACE_MODE_SGMII ||
 	     phydev->interface == PHY_INTERFACE_MODE_2500BASEX ||
-	     phydev->interface == PHY_INTERFACE_MODE_10GKR) && phydev->link) {
+	     phydev->interface == PHY_INTERFACE_MODE_10GBASER) &&
+	    phydev->link) {
 		/* The PHY automatically switches its serdes interface (and
-		 * active PHYXS instance) between Cisco SGMII, 10GBase-KR and
+		 * active PHYXS instance) between Cisco SGMII, 10GBase-R and
 		 * 2500BaseX modes according to the speed.  Florian suggests
 		 * setting phydev->interface to communicate this to the MAC.
 		 * Only do this if we are already in one of the above modes.
 		 */
 		switch (phydev->speed) {
 		case SPEED_10000:
-			phydev->interface = PHY_INTERFACE_MODE_10GKR;
+			phydev->interface = PHY_INTERFACE_MODE_10GBASER;
 			break;
 		case SPEED_2500:
 			phydev->interface = PHY_INTERFACE_MODE_2500BASEX;

drivers/net/phy/phylink.c

@@ -298,6 +298,7 @@ static int phylink_parse_mode(struct phylink *pl, struct fwnode_handle *fwnode)
 			break;
 
 		case PHY_INTERFACE_MODE_10GKR:
+		case PHY_INTERFACE_MODE_10GBASER:
 			phylink_set(pl->supported, 10baseT_Half);
 			phylink_set(pl->supported, 10baseT_Full);
 			phylink_set(pl->supported, 100baseT_Half);

drivers/net/phy/sfp-bus.c

@@ -373,7 +373,7 @@ phy_interface_t sfp_select_interface(struct sfp_bus *bus,
 	    phylink_test(link_modes, 10000baseLRM_Full) ||
 	    phylink_test(link_modes, 10000baseER_Full) ||
 	    phylink_test(link_modes, 10000baseT_Full))
-		return PHY_INTERFACE_MODE_10GKR;
+		return PHY_INTERFACE_MODE_10GBASER;
 
 	if (phylink_test(link_modes, 2500baseX_Full))
 		return PHY_INTERFACE_MODE_2500BASEX;

drivers/phy/marvell/phy-mvebu-cp110-comphy.c

@@ -221,7 +221,7 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = {
 	ETH_CONF(2, 0, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII),
 	ETH_CONF(2, 0, PHY_INTERFACE_MODE_2500BASEX, 0x1, COMPHY_FW_MODE_HS_SGMII),
 	ETH_CONF(2, 0, PHY_INTERFACE_MODE_RXAUI, 0x1, COMPHY_FW_MODE_RXAUI),
-	ETH_CONF(2, 0, PHY_INTERFACE_MODE_10GKR, 0x1, COMPHY_FW_MODE_XFI),
+	ETH_CONF(2, 0, PHY_INTERFACE_MODE_10GBASER, 0x1, COMPHY_FW_MODE_XFI),
 	GEN_CONF(2, 0, PHY_MODE_USB_HOST_SS, COMPHY_FW_MODE_USB3H),
 	GEN_CONF(2, 0, PHY_MODE_SATA, COMPHY_FW_MODE_SATA),
 	GEN_CONF(2, 0, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE),
@@ -235,14 +235,14 @@ static const struct mvebu_comphy_conf mvebu_comphy_cp110_modes[] = {
 	/* lane 4 */
 	ETH_CONF(4, 0, PHY_INTERFACE_MODE_SGMII, 0x2, COMPHY_FW_MODE_SGMII),
 	ETH_CONF(4, 0, PHY_INTERFACE_MODE_2500BASEX, 0x2, COMPHY_FW_MODE_HS_SGMII),
-	ETH_CONF(4, 0, PHY_INTERFACE_MODE_10GKR, 0x2, COMPHY_FW_MODE_XFI),
+	ETH_CONF(4, 0, PHY_INTERFACE_MODE_10GBASER, 0x2, COMPHY_FW_MODE_XFI),
 	ETH_CONF(4, 0, PHY_INTERFACE_MODE_RXAUI, 0x2, COMPHY_FW_MODE_RXAUI),
 	GEN_CONF(4, 0, PHY_MODE_USB_DEVICE_SS, COMPHY_FW_MODE_USB3D),
 	GEN_CONF(4, 1, PHY_MODE_USB_HOST_SS, COMPHY_FW_MODE_USB3H),
 	GEN_CONF(4, 1, PHY_MODE_PCIE, COMPHY_FW_MODE_PCIE),
 	ETH_CONF(4, 1, PHY_INTERFACE_MODE_SGMII, 0x1, COMPHY_FW_MODE_SGMII),
 	ETH_CONF(4, 1, PHY_INTERFACE_MODE_2500BASEX, -1, COMPHY_FW_MODE_HS_SGMII),
-	ETH_CONF(4, 1, PHY_INTERFACE_MODE_10GKR, -1, COMPHY_FW_MODE_XFI),
+	ETH_CONF(4, 1, PHY_INTERFACE_MODE_10GBASER, -1, COMPHY_FW_MODE_XFI),
 	/* lane 5 */
 	ETH_CONF(5, 1, PHY_INTERFACE_MODE_RXAUI, 0x2, COMPHY_FW_MODE_RXAUI),
 	GEN_CONF(5, 1, PHY_MODE_SATA, COMPHY_FW_MODE_SATA),
@@ -342,7 +342,7 @@ static int mvebu_comphy_ethernet_init_reset(struct mvebu_comphy_lane *lane)
 		 MVEBU_COMPHY_SERDES_CFG0_RXAUI_MODE);
 
 	switch (lane->submode) {
-	case PHY_INTERFACE_MODE_10GKR:
+	case PHY_INTERFACE_MODE_10GBASER:
 		val |= MVEBU_COMPHY_SERDES_CFG0_GEN_RX(0xe) |
 		       MVEBU_COMPHY_SERDES_CFG0_GEN_TX(0xe);
 		break;
@@ -417,7 +417,7 @@ static int mvebu_comphy_ethernet_init_reset(struct mvebu_comphy_lane *lane)
 	/* refclk selection */
 	val = readl(priv->base + MVEBU_COMPHY_MISC_CTRL0(lane->id));
 	val &= ~MVEBU_COMPHY_MISC_CTRL0_REFCLK_SEL;
-	if (lane->submode == PHY_INTERFACE_MODE_10GKR)
+	if (lane->submode == PHY_INTERFACE_MODE_10GBASER)
 		val |= MVEBU_COMPHY_MISC_CTRL0_ICP_FORCE;
 	writel(val, priv->base + MVEBU_COMPHY_MISC_CTRL0(lane->id));
 
@@ -564,7 +564,7 @@ static int mvebu_comphy_set_mode_rxaui(struct phy *phy)
 	return mvebu_comphy_init_plls(lane);
 }
 
-static int mvebu_comphy_set_mode_10gkr(struct phy *phy)
+static int mvebu_comphy_set_mode_10gbaser(struct phy *phy)
 {
 	struct mvebu_comphy_lane *lane = phy_get_drvdata(phy);
 	struct mvebu_comphy_priv *priv = lane->priv;
@@ -735,8 +735,8 @@ static int mvebu_comphy_power_on_legacy(struct phy *phy)
 	case PHY_INTERFACE_MODE_RXAUI:
 		ret = mvebu_comphy_set_mode_rxaui(phy);
 		break;
-	case PHY_INTERFACE_MODE_10GKR:
-		ret = mvebu_comphy_set_mode_10gkr(phy);
+	case PHY_INTERFACE_MODE_10GBASER:
+		ret = mvebu_comphy_set_mode_10gbaser(phy);
 		break;
 	default:
 		return -ENOTSUPP;
@@ -782,8 +782,8 @@ static int mvebu_comphy_power_on(struct phy *phy)
 				lane->id);
 			fw_speed = COMPHY_FW_SPEED_3125;
 			break;
-		case PHY_INTERFACE_MODE_10GKR:
-			dev_dbg(priv->dev, "set lane %d to 10G-KR mode\n",
+		case PHY_INTERFACE_MODE_10GBASER:
+			dev_dbg(priv->dev, "set lane %d to 10GBASE-R mode\n",
 				lane->id);
 			fw_speed = COMPHY_FW_SPEED_103125;
 			break;