Commit e1ce697d authored by Greg Kroah-Hartman's avatar Greg Kroah-Hartman

Merge branch 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Thomas writes:
  "Three small fixes for clocksource drivers:
   - Proper error handling in the Atmel PIT driver
   - Add CLOCK_SOURCE_SUSPEND_NONSTOP for TI SoCs so suspend works again
   - Fix the next event function for Facebook Backpack-CMM BMC chips so
     usleep(100) doesnt sleep several milliseconds"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource/drivers/timer-atmel-pit: Properly handle error cases
  clocksource/drivers/fttmr010: Fix set_next_event handler
  clocksource/drivers/ti-32k: Add CLOCK_SOURCE_SUSPEND_NONSTOP flag for non-am43 SoCs
parents af17b3aa 090bcfd5
......@@ -180,26 +180,29 @@ static int __init at91sam926x_pit_dt_init(struct device_node *node)
data->base = of_iomap(node, 0);
if (!data->base) {
pr_err("Could not map PIT address\n");
return -ENXIO;
ret = -ENXIO;
goto exit;
}
data->mck = of_clk_get(node, 0);
if (IS_ERR(data->mck)) {
pr_err("Unable to get mck clk\n");
return PTR_ERR(data->mck);
ret = PTR_ERR(data->mck);
goto exit;
}
ret = clk_prepare_enable(data->mck);
if (ret) {
pr_err("Unable to enable mck\n");
return ret;
goto exit;
}
/* Get the interrupts property */
data->irq = irq_of_parse_and_map(node, 0);
if (!data->irq) {
pr_err("Unable to get IRQ from DT\n");
return -EINVAL;
ret = -EINVAL;
goto exit;
}
/*
......@@ -227,7 +230,7 @@ static int __init at91sam926x_pit_dt_init(struct device_node *node)
ret = clocksource_register_hz(&data->clksrc, pit_rate);
if (ret) {
pr_err("Failed to register clocksource\n");
return ret;
goto exit;
}
/* Set up irq handler */
......@@ -236,7 +239,8 @@ static int __init at91sam926x_pit_dt_init(struct device_node *node)
"at91_tick", data);
if (ret) {
pr_err("Unable to setup IRQ\n");
return ret;
clocksource_unregister(&data->clksrc);
goto exit;
}
/* Set up and register clockevents */
......@@ -254,6 +258,10 @@ static int __init at91sam926x_pit_dt_init(struct device_node *node)
clockevents_register_device(&data->clkevt);
return 0;
exit:
kfree(data);
return ret;
}
TIMER_OF_DECLARE(at91sam926x_pit, "atmel,at91sam9260-pit",
at91sam926x_pit_dt_init);
......@@ -130,13 +130,17 @@ static int fttmr010_timer_set_next_event(unsigned long cycles,
cr &= ~fttmr010->t1_enable_val;
writel(cr, fttmr010->base + TIMER_CR);
/* Setup the match register forward/backward in time */
cr = readl(fttmr010->base + TIMER1_COUNT);
if (fttmr010->count_down)
cr -= cycles;
else
cr += cycles;
writel(cr, fttmr010->base + TIMER1_MATCH1);
if (fttmr010->count_down) {
/*
* ASPEED Timer Controller will load TIMER1_LOAD register
* into TIMER1_COUNT register when the timer is re-enabled.
*/
writel(cycles, fttmr010->base + TIMER1_LOAD);
} else {
/* Setup the match register forward in time */
cr = readl(fttmr010->base + TIMER1_COUNT);
writel(cr + cycles, fttmr010->base + TIMER1_MATCH1);
}
/* Start */
cr = readl(fttmr010->base + TIMER_CR);
......
......@@ -97,6 +97,9 @@ static int __init ti_32k_timer_init(struct device_node *np)
return -ENXIO;
}
if (!of_machine_is_compatible("ti,am43"))
ti_32k_timer.cs.flags |= CLOCK_SOURCE_SUSPEND_NONSTOP;
ti_32k_timer.counter = ti_32k_timer.base;
/*
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment