arm64: dts: qcom: sa8295p-adp: use sa8540p-pmics

Include the dtsi to use a single pmic descriptions.
Both sa8295p-adp and sa8540p-adp have the same spmi pmic apparently.
Signed-off-by: Eric Chanudet <echanude@redhat.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Tested-by: Andrew Halaney <ahalaney@redhat.com> # sa8540p-ride
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20221219191000.2570545-4-echanude@redhat.com

arch/arm64/boot/dts/qcom/sa8295p-adp.dts

@@ -11,6 +11,7 @@
 #include <dt-bindings/spmi/spmi.h>
 
 #include "sa8540p.dtsi"
+#include "sa8540p-pmics.dtsi"
 
 / {
 	model = "Qualcomm SA8295P ADP";
@@ -260,84 +261,6 @@ &remoteproc_nsp1 {
 	status = "okay";
 };
 
-&spmi_bus {
-	pm8450a: pmic@0 {
-		compatible = "qcom,pm8150", "qcom,spmi-pmic";
-		reg = <0x0 SPMI_USID>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		rtc@6000 {
-			compatible = "qcom,pm8941-rtc";
-			reg = <0x6000>;
-			reg-names = "rtc", "alarm";
-			interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>;
-			wakeup-source;
-		};
-
-		pm8450a_gpios: gpio@c000 {
-			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
-			reg = <0xc000>;
-			gpio-controller;
-			gpio-ranges = <&pm8450a_gpios 0 0 10>;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-	};
-
-	pm8450c: pmic@4 {
-		compatible = "qcom,pm8150", "qcom,spmi-pmic";
-		reg = <0x4 SPMI_USID>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		pm8450c_gpios: gpio@c000 {
-			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
-			reg = <0xc000>;
-			gpio-controller;
-			gpio-ranges = <&pm8450c_gpios 0 0 10>;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-	};
-
-	pm8450e: pmic@8 {
-		compatible = "qcom,pm8150", "qcom,spmi-pmic";
-		reg = <0x8 SPMI_USID>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		pm8450e_gpios: gpio@c000 {
-			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
-			reg = <0xc000>;
-			gpio-controller;
-			gpio-ranges = <&pm8450e_gpios 0 0 10>;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-	};
-
-	pm8450g: pmic@c {
-		compatible = "qcom,pm8150", "qcom,spmi-pmic";
-		reg = <0xc SPMI_USID>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		pm8450g_gpios: gpio@c000 {
-			compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio";
-			reg = <0xc000>;
-			gpio-controller;
-			gpio-ranges = <&pm8450g_gpios 0 0 10>;
-			#gpio-cells = <2>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-	};
-};
-
 &ufs_mem_hc {
 	reset-gpios = <&tlmm 228 GPIO_ACTIVE_LOW>;