Merge branch 'mvneta-phylink'

Russell King says:

====================
Convert mvneta to phylink supported_interfaces

This patch series converts mvneta to use phylinks supported_interfaces
bitmap to simplify the validate() implementation. The patches:

1) Add the supported interface modes the supported_interfaces bitmap.
2) Removes the checks for the interface type being supported from
   the validate callback
3) Removes the now unnecessary checks and call to
   phylink_helper_basex_speed() to support switching between
   1000base-X and 2500base-X for SFPs

(3) becomes possible because when asking the MAC for its complete
support, we walk all supported interfaces which will include 1000base-X
and 2500base-X only if the comphy is present.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/marvell/mvneta.c

@@ -3823,8 +3823,6 @@ static void mvneta_validate(struct phylink_config *config,
 			    unsigned long *supported,
 			    struct phylink_link_state *state)
 {
-	struct net_device *ndev = to_net_dev(config->dev);
-	struct mvneta_port *pp = netdev_priv(ndev);
 	__ETHTOOL_DECLARE_LINK_MODE_MASK(mask) = { 0, };
 
 	/* We only support QSGMII, SGMII, 802.3z and RGMII modes.
@@ -3832,15 +3830,8 @@ static void mvneta_validate(struct phylink_config *config,
 	 * "Bit 2 Field InBandAnEn In-band Auto-Negotiation enable. ...
 	 * When <PortType> = 1 (1000BASE-X) this field must be set to 1."
 	 */
-	if (phy_interface_mode_is_8023z(state->interface)) {
-		if (!phylink_test(state->advertising, Autoneg)) {
-			linkmode_zero(supported);
-			return;
-		}
-	} else if (state->interface != PHY_INTERFACE_MODE_NA &&
-		   state->interface != PHY_INTERFACE_MODE_QSGMII &&
-		   state->interface != PHY_INTERFACE_MODE_SGMII &&
-		   !phy_interface_mode_is_rgmii(state->interface)) {
+	if (phy_interface_mode_is_8023z(state->interface) &&
+	    !phylink_test(state->advertising, Autoneg)) {
 		linkmode_zero(supported);
 		return;
 	}
@@ -3853,11 +3844,12 @@ static void mvneta_validate(struct phylink_config *config,
 	phylink_set(mask, Pause);
 
 	/* Half-duplex at speeds higher than 100Mbit is unsupported */
-	if (pp->comphy || state->interface != PHY_INTERFACE_MODE_2500BASEX) {
+	if (state->interface != PHY_INTERFACE_MODE_2500BASEX) {
 		phylink_set(mask, 1000baseT_Full);
 		phylink_set(mask, 1000baseX_Full);
 	}
-	if (pp->comphy || state->interface == PHY_INTERFACE_MODE_2500BASEX) {
+
+	if (state->interface == PHY_INTERFACE_MODE_2500BASEX) {
 		phylink_set(mask, 2500baseT_Full);
 		phylink_set(mask, 2500baseX_Full);
 	}
@@ -3872,11 +3864,6 @@ static void mvneta_validate(struct phylink_config *config,
 
 	linkmode_and(supported, supported, mask);
 	linkmode_and(state->advertising, state->advertising, mask);
-
-	/* We can only operate at 2500BaseX or 1000BaseX.  If requested
-	 * to advertise both, only report advertising at 2500BaseX.
-	 */
-	phylink_helper_basex_speed(state);
 }
 
 static void mvneta_mac_pcs_get_state(struct phylink_config *config,
@@ -5179,6 +5166,31 @@ static int mvneta_probe(struct platform_device *pdev)
 
 	pp->phylink_config.dev = &dev->dev;
 	pp->phylink_config.type = PHYLINK_NETDEV;
+	phy_interface_set_rgmii(pp->phylink_config.supported_interfaces);
+	__set_bit(PHY_INTERFACE_MODE_QSGMII,
+		  pp->phylink_config.supported_interfaces);
+	if (comphy) {
+		/* If a COMPHY is present, we can support any of the serdes
+		 * modes and switch between them.
+		 */
+		__set_bit(PHY_INTERFACE_MODE_SGMII,
+			  pp->phylink_config.supported_interfaces);
+		__set_bit(PHY_INTERFACE_MODE_1000BASEX,
+			  pp->phylink_config.supported_interfaces);
+		__set_bit(PHY_INTERFACE_MODE_2500BASEX,
+			  pp->phylink_config.supported_interfaces);
+	} else if (phy_mode == PHY_INTERFACE_MODE_2500BASEX) {
+		/* No COMPHY, with only 2500BASE-X mode supported */
+		__set_bit(PHY_INTERFACE_MODE_2500BASEX,
+			  pp->phylink_config.supported_interfaces);
+	} else if (phy_mode == PHY_INTERFACE_MODE_1000BASEX ||
+		   phy_mode == PHY_INTERFACE_MODE_SGMII) {
+		/* No COMPHY, we can switch between 1000BASE-X and SGMII */
+		__set_bit(PHY_INTERFACE_MODE_1000BASEX,
+			  pp->phylink_config.supported_interfaces);
+		__set_bit(PHY_INTERFACE_MODE_SGMII,
+			  pp->phylink_config.supported_interfaces);
+	}
 
 	phylink = phylink_create(&pp->phylink_config, pdev->dev.fwnode,
 				 phy_mode, &mvneta_phylink_ops);