drm/msm/disp/dpu: get timing engine status from intf status register

Recommended way of reading the interface timing gen status is via
status register. Timing gen status register will give a reliable status
of the interface especially during ON/OFF transitions. This support was
added from DPU version 5.0.0.
Signed-off-by: Vinod Polimera <quic_vpolimer@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/524724/
Link: https://lore.kernel.org/r/1677774797-31063-6-git-send-email-quic_vpolimer@quicinc.comSigned-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.c

@@ -78,7 +78,8 @@
 
 #define INTF_SDM845_MASK (0)
 
-#define INTF_SC7180_MASK BIT(DPU_INTF_INPUT_CTRL) | BIT(DPU_INTF_TE)
+#define INTF_SC7180_MASK \
+	(BIT(DPU_INTF_INPUT_CTRL) | BIT(DPU_INTF_TE) | BIT(DPU_INTF_STATUS_SUPPORTED))
 
 #define INTF_SC7280_MASK INTF_SC7180_MASK | BIT(DPU_DATA_HCTL_EN)
 

drivers/gpu/drm/msm/disp/dpu1/dpu_hw_catalog.h

@@ -213,17 +213,19 @@ enum {
 
 /**
  * INTF sub-blocks
- * @DPU_INTF_INPUT_CTRL         Supports the setting of pp block from which
- *                              pixel data arrives to this INTF
- * @DPU_INTF_TE                 INTF block has TE configuration support
- * @DPU_DATA_HCTL_EN            Allows data to be transferred at different rate
-                                than video timing
+ * @DPU_INTF_INPUT_CTRL             Supports the setting of pp block from which
+ *                                  pixel data arrives to this INTF
+ * @DPU_INTF_TE                     INTF block has TE configuration support
+ * @DPU_DATA_HCTL_EN                Allows data to be transferred at different rate
+ *                                  than video timing
+ * @DPU_INTF_STATUS_SUPPORTED       INTF block has INTF_STATUS register
  * @DPU_INTF_MAX
  */
 enum {
 	DPU_INTF_INPUT_CTRL = 0x1,
 	DPU_INTF_TE,
 	DPU_DATA_HCTL_EN,
+	DPU_INTF_STATUS_SUPPORTED,
 	DPU_INTF_MAX
 };
 

drivers/gpu/drm/msm/disp/dpu1/dpu_hw_intf.c

@@ -62,6 +62,7 @@
 #define   INTF_LINE_COUNT               0x0B0
 
 #define   INTF_MUX                      0x25C
+#define   INTF_STATUS                   0x26C
 
 #define INTF_CFG_ACTIVE_H_EN	BIT(29)
 #define INTF_CFG_ACTIVE_V_EN	BIT(30)
@@ -297,8 +298,13 @@ static void dpu_hw_intf_get_status(
 		struct intf_status *s)
 {
 	struct dpu_hw_blk_reg_map *c = &intf->hw;
+	unsigned long cap = intf->cap->features;
+
+	if (cap & BIT(DPU_INTF_STATUS_SUPPORTED))
+		s->is_en = DPU_REG_READ(c, INTF_STATUS) & BIT(0);
+	else
+		s->is_en = DPU_REG_READ(c, INTF_TIMING_ENGINE_EN);
 
-	s->is_en = DPU_REG_READ(c, INTF_TIMING_ENGINE_EN);
 	s->is_prog_fetch_en = !!(DPU_REG_READ(c, INTF_CONFIG) & BIT(31));
 	if (s->is_en) {
 		s->frame_count = DPU_REG_READ(c, INTF_FRAME_COUNT);