Commit e65953d4 authored by Chunyan Zhang's avatar Chunyan Zhang Committed by Ulf Hansson

mmc: sdhci: Add 32-bit block count support for v4 mode

Host Controller Version 4.10 re-defines SDMA System Address register
as 32-bit Block Count for v4 mode, and SDMA uses ADMA System
Address register (05Fh-058h) instead if v4 mode is enabled. Also
when using 32-bit block count, 16-bit block count register need
to be set to zero.

Since using 32-bit Block Count would cause problems for auto-cmd23,
it can be chosen via host->quirk2.
Signed-off-by: default avatarChunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: default avatarAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: default avatarUlf Hansson <ulf.hansson@linaro.org>
parent 685e444b
......@@ -1082,7 +1082,19 @@ static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
/* Set the DMA boundary value and block size */
sdhci_writew(host, SDHCI_MAKE_BLKSZ(host->sdma_boundary, data->blksz),
SDHCI_BLOCK_SIZE);
sdhci_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
/*
* For Version 4.10 onwards, if v4 mode is enabled, 32-bit Block Count
* can be supported, in that case 16-bit block count register must be 0.
*/
if (host->version >= SDHCI_SPEC_410 && host->v4_mode &&
(host->quirks2 & SDHCI_QUIRK2_USE_32BIT_BLK_CNT)) {
if (sdhci_readw(host, SDHCI_BLOCK_COUNT))
sdhci_writew(host, 0, SDHCI_BLOCK_COUNT);
sdhci_writew(host, data->blocks, SDHCI_32BIT_BLK_CNT);
} else {
sdhci_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
}
}
static inline bool sdhci_auto_cmd12(struct sdhci_host *host,
......
......@@ -28,6 +28,7 @@
#define SDHCI_DMA_ADDRESS 0x00
#define SDHCI_ARGUMENT2 SDHCI_DMA_ADDRESS
#define SDHCI_32BIT_BLK_CNT SDHCI_DMA_ADDRESS
#define SDHCI_BLOCK_SIZE 0x04
#define SDHCI_MAKE_BLKSZ(dma, blksz) (((dma & 0x7) << 12) | (blksz & 0xFFF))
......@@ -462,6 +463,13 @@ struct sdhci_host {
* obtainable timeout.
*/
#define SDHCI_QUIRK2_DISABLE_HW_TIMEOUT (1<<17)
/*
* 32-bit block count may not support eMMC where upper bits of CMD23 are used
* for other purposes. Consequently we support 16-bit block count by default.
* Otherwise, SDHCI_QUIRK2_USE_32BIT_BLK_CNT can be selected to use 32-bit
* block count.
*/
#define SDHCI_QUIRK2_USE_32BIT_BLK_CNT (1<<18)
int irq; /* Device IRQ */
void __iomem *ioaddr; /* Mapped address */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment