dt-bindings: power: supply: bq24190: Convert to DT schema format

Convert the binding to DT schema format.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>

Documentation/devicetree/bindings/power/supply/bq24190.txt

-TI BQ24190 Li-Ion Battery Charger
-
-Required properties:
-- compatible: contains one of the following:
-    * "ti,bq24190"
-    * "ti,bq24192"
-    * "ti,bq24192i"
-    * "ti,bq24196"
-- reg: integer, I2C address of the charger.
-- interrupts[-extended]: configuration for charger INT pin.
-
-Optional properties:
-- monitored-battery: phandle of battery characteristics devicetree node
-  The charger uses the following battery properties:
-    + precharge-current-microamp: maximum charge current during precharge
-      phase (typically 20% of battery capacity).
-    + charge-term-current-microamp: a charge cycle terminates when the
-      battery voltage is above recharge threshold, and the current is below
-      this setting (typically 10% of battery capacity).
-  See also Documentation/devicetree/bindings/power/supply/battery.txt
-- ti,system-minimum-microvolt: when power is connected and the battery is below
-  minimum system voltage, the system will be regulated above this setting.
-
-child nodes:
-- usb-otg-vbus:
-  Usage: optional
-  Description: Regulator that is used to control the VBUS voltage direction for
-               either USB host mode or for charging on the OTG port.
-
-Notes:
-- Some circuit boards wire the chip's "OTG" pin high (enabling 500mA default
-  charge current on USB SDP ports, among other features). To simulate this on
-  boards that wire the pin to a GPIO, set a gpio-hog.
-
-Example:
-
-	bat: battery {
-		compatible = "simple-battery";
-		precharge-current-microamp = <256000>;
-		charge-term-current-microamp = <128000>;
-		// etc.
-	};
-
-	bq24190: charger@6a {
-		compatible = "ti,bq24190";
-		reg = <0x6a>;
-		interrupts-extended = <&gpiochip 10 IRQ_TYPE_EDGE_FALLING>;
-		monitored-battery = <&bat>;
-		ti,system-minimum-microvolt = <3200000>;
-
-		usb_otg_vbus: usb-otg-vbus { };
-	};
-
-	&twl_gpio {
-		otg {
-			gpio-hog;
-			gpios = <6 0>;
-			output-high;
-			line-name = "otg-gpio";
-		};
-	};

Documentation/devicetree/bindings/power/supply/bq24190.yaml

+# SPDX-License-Identifier: GPL-2.0
+# Copyright (C) 2021 Sebastian Reichel
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/power/supply/bq24190.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: Binding for TI BQ2419x Li-Ion Battery Charger
+
+maintainers:
+  - Sebastian Reichel <sre@kernel.org>
+
+allOf:
+  - $ref: power-supply.yaml#
+
+properties:
+  compatible:
+    enum:
+      - ti,bq24190
+      - ti,bq24192
+      - ti,bq24192i
+      - ti,bq24196
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  usb-otg-vbus:
+    type: object
+    description: |
+      Regulator that is used to control the VBUS voltage direction for
+      either USB host mode or for charging on the OTG port
+
+  ti,system-minimum-microvolt:
+    description: |
+      when power is connected and the battery is below minimum system voltage,
+      the system will be regulated above this setting.
+
+  omit-battery-class:
+    type: boolean
+    description: |
+      If this property is set, the operating system does not try to create a
+      battery device.
+
+  monitored-battery:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: |
+      phandle to a "simple-battery" compatible node.
+
+      This property must be a phandle to a node using the format described
+      in battery.yaml, with the following properties being required:
+      - precharge-current-microamp: maximum charge current during precharge phase
+                                    (typically 20% of battery capacity).
+      - charge-term-current-microamp: a charge cycle terminates when the battery voltage is
+                                      above recharge threshold, and the current is below this
+                                      setting (typically 10% of battery capacity).
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    bat: battery {
+      compatible = "simple-battery";
+      precharge-current-microamp = <256000>;
+      charge-term-current-microamp = <128000>;
+    };
+
+    i2c0 {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      charger@6a {
+        compatible = "ti,bq24190";
+        reg = <0x6a>;
+        interrupt-parent = <&gpiochip>;
+        interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
+        monitored-battery = <&bat>;
+        ti,system-minimum-microvolt = <3200000>;
+
+        usb_otg_vbus: usb-otg-vbus { };
+      };
+    };