[ARM PATCH] 1603/1: [PATCH] 9/10 Simpad changes

Patch from Holger Freyther

include/asm-arm/arch-sa1100/simpad.h

@@ -5,17 +5,13 @@
  *
  * This file contains the hardware specific definitions for SIMpad
  *
- * 2001/05/14 Juergen Messerer <juergen.messerer@siemens.ch>
+ * 2001/05/14 Juergen Messerer <juergen.messerer@freesurf.ch>
  */
 
-#ifndef SIMPAD_H
-#define SIMPAD_H
+#ifndef __ASM_ARCH_SIMPAD_H
+#define __ASM_ARCH_SIMPAD_H
 
 
-#ifndef __ASM_ARCH_HARDWARE_H
-#error "include <asm/hardware.h> instead"
-#endif
-
 #define GPIO_UART1_RTS	GPIO_GPIO14
 #define GPIO_UART1_DTR	GPIO_GPIO7
 #define GPIO_UART1_CTS	GPIO_GPIO8
@@ -28,7 +24,8 @@
 #define GPIO_UART3_DCD	GPIO_GPIO18
 #define GPIO_UART3_DSR	GPIO_GPIO17
 
-#define GPIO_UCB1300_IRQ	GPIO_GPIO (22)	/* UCB GPIO and touchscreen */
+#define GPIO_POWER_BUTTON	GPIO_GPIO0
+#define GPIO_UCB1300_IRQ	GPIO_GPIO22	/* UCB GPIO and touchscreen */
 
 #define IRQ_UART1_CTS	IRQ_GPIO15
 #define IRQ_UART1_DCD	GPIO_GPIO23
@@ -37,21 +34,26 @@
 #define IRQ_UART3_DCD	GPIO_GPIO18
 #define IRQ_UART3_DSR	GPIO_GPIO17
 
-#define IRQ_GPIO_UCB1300_IRQ IRQ_GPIO22 
+#define IRQ_GPIO_UCB1300_IRQ IRQ_GPIO22
+#define IRQ_GPIO_POWER_BUTTON IRQ_GPIO0
 
 
 /*---  PCMCIA  ---*/
 #define GPIO_CF_CD              GPIO_GPIO24
-#define GPIO_CF_IRQ             GPIO_GPIO1          
+#define GPIO_CF_IRQ             GPIO_GPIO1
 #define IRQ_GPIO_CF_IRQ         IRQ_GPIO1
-#define IRQ_GPIO_CF_CD          IRQ_GPIO24      
+#define IRQ_GPIO_CF_CD          IRQ_GPIO24
+
+/*--- SmartCard ---*/
+#define GPIO_SMART_CARD		GPIO_GPIO10
+#define IRQ_GPIO_SMARD_CARD	IRQ_GPIO10
 
-// CS3 Latch is write only, a shadow is necessary 
+// CS3 Latch is write only, a shadow is necessary
 
-#define CS3BUSTYPE unsigned volatile long           
+#define CS3BUSTYPE unsigned volatile long
 #define CS3_BASE        0xf1000000
 
-#define VCC_5V_EN       0x0001 // For 5V PCMCIA 
+#define VCC_5V_EN       0x0001 // For 5V PCMCIA
 #define VCC_3V_EN       0x0002 // FOR 3.3V PCMCIA
 #define EN1             0x0004 // This is only for EPROM's
 #define EN0             0x0008 // Both should be enable for 3.3V or 5V
@@ -63,15 +65,43 @@
 #define IRDA_SD         0x0200 // Shutdown for powersave
 #define RS232_ON        0x0400
 #define SD_MEDIAQ       0x0800 // Shutdown for powersave
-#define LED2_ON         0x1000 
+#define LED2_ON         0x1000
 #define IRDA_MODE       0x2000 // Fast/Slow IrDA mode
 #define ENABLE_5V       0x4000 // Enable 5V circuit
 #define RESET_SIMCARD   0x8000
 
 #define RS232_ENABLE    0x0440
-#define PCMCIAMASK      0x402f   
-
-#endif // SIMPAD_H
+#define PCMCIAMASK      0x402f
+
+
+struct simpad_battery {
+	unsigned char ac_status;	/* line connected yes/no */
+	unsigned char status;		/* battery loading yes/no */
+	unsigned char percentage;	/* percentage loaded */
+	unsigned short life;		/* life till empty */
+};
+
+/* These should match the apm_bios.h definitions */
+#define SIMPAD_AC_STATUS_AC_OFFLINE      0x00
+#define SIMPAD_AC_STATUS_AC_ONLINE       0x01
+#define SIMPAD_AC_STATUS_AC_BACKUP       0x02   /* What does this mean? */
+#define SIMPAD_AC_STATUS_AC_UNKNOWN      0xff
+
+/* These bitfields are rarely "or'd" together */
+#define SIMPAD_BATT_STATUS_HIGH          0x01
+#define SIMPAD_BATT_STATUS_LOW           0x02
+#define SIMPAD_BATT_STATUS_CRITICAL      0x04
+#define SIMPAD_BATT_STATUS_CHARGING      0x08
+#define SIMPAD_BATT_STATUS_CHARGE_MAIN   0x10
+#define SIMPAD_BATT_STATUS_DEAD          0x20   /* Battery will not charge */
+#define SIMPAD_BATT_NOT_INSTALLED        0x20   /* For expansion pack batteries */
+#define SIMPAD_BATT_STATUS_FULL          0x40   /* Battery fully charged (and connected to AC) */
+#define SIMPAD_BATT_STATUS_NOBATT        0x80
+#define SIMPAD_BATT_STATUS_UNKNOWN       0xff
+
+extern int simpad_get_battery(struct simpad_battery* );
+
+#endif // __ASM_ARCH_SIMPAD_H