scsi: lpfc: Fix mailbox command failure during driver initialization

Contention for the mailbox interface may occur during driver initialization
(immediately after a function reset), between mailbox commands initiated
via ioctl (bsg) and those driver requested by the driver.

After setting SLI_ACTIVE flag for a port, there is a window in which the
driver will allow an ioctl to be initiated while the adapter is
initializing and issuing mailbox commands via polling. The polling logic
then gets confused.

Correct by having thread setting SLI_ACTIVE spot an active mailbox command
and allow it complete before proceeding.

Link: https://lore.kernel.org/r/20210921143008.64212-1-jsmart2021@gmail.comCo-developed-by: Nigel Kirkland <nkirkland2304@gmail.com>
Signed-off-by: Nigel Kirkland <nkirkland2304@gmail.com>
Signed-off-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>

drivers/scsi/lpfc/lpfc_sli.c

@@ -8158,6 +8158,7 @@ lpfc_sli4_hba_setup(struct lpfc_hba *phba)
 	struct lpfc_vport *vport = phba->pport;
 	struct lpfc_dmabuf *mp;
 	struct lpfc_rqb *rqbp;
+	u32 flg;
 
 	/* Perform a PCI function reset to start from clean */
 	rc = lpfc_pci_function_reset(phba);
@@ -8171,7 +8172,17 @@ lpfc_sli4_hba_setup(struct lpfc_hba *phba)
 	else {
 		spin_lock_irq(&phba->hbalock);
 		phba->sli.sli_flag |= LPFC_SLI_ACTIVE;
+		flg = phba->sli.sli_flag;
 		spin_unlock_irq(&phba->hbalock);
+		/* Allow a little time after setting SLI_ACTIVE for any polled
+		 * MBX commands to complete via BSG.
+		 */
+		for (i = 0; i < 50 && (flg & LPFC_SLI_MBOX_ACTIVE); i++) {
+			msleep(20);
+			spin_lock_irq(&phba->hbalock);
+			flg = phba->sli.sli_flag;
+			spin_unlock_irq(&phba->hbalock);
+		}
 	}
 
 	lpfc_sli4_dip(phba);
@@ -9755,7 +9766,7 @@ lpfc_sli_issue_mbox_s4(struct lpfc_hba *phba, LPFC_MBOXQ_t *mboxq,
 					"(%d):2541 Mailbox command x%x "
 					"(x%x/x%x) failure: "
 					"mqe_sta: x%x mcqe_sta: x%x/x%x "
-					"Data: x%x x%x\n,",
+					"Data: x%x x%x\n",
 					mboxq->vport ? mboxq->vport->vpi : 0,
 					mboxq->u.mb.mbxCommand,
 					lpfc_sli_config_mbox_subsys_get(phba,
@@ -9789,7 +9800,7 @@ lpfc_sli_issue_mbox_s4(struct lpfc_hba *phba, LPFC_MBOXQ_t *mboxq,
 					"(%d):2597 Sync Mailbox command "
 					"x%x (x%x/x%x) failure: "
 					"mqe_sta: x%x mcqe_sta: x%x/x%x "
-					"Data: x%x x%x\n,",
+					"Data: x%x x%x\n",
 					mboxq->vport ? mboxq->vport->vpi : 0,
 					mboxq->u.mb.mbxCommand,
 					lpfc_sli_config_mbox_subsys_get(phba,