Merge tag 'iio-fixes-for-5.17a' of...

Merge tag 'iio-fixes-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus

Jonathan writes:

1st set of IIO fixes for the 5.17 cycle.

Several drivers:
 - Fix a failure to disable runtime in probe error paths. All cases
   were introduced in the same rework patch.

adi,ad7124
 - Fix incorrect register masking.
adi,ad74413r
 - Avoid referencing negative array offsets.
 - Use ngpio size when iterating over mask not numebr of channels.
 - Fix issue with wrong mask uage getting GPIOs.
adi,admv1014
 - Drop check on unsigned less than 0.
adi,ads16480
 - Correctly handle devices that don't have burst mode support.
fsl,fxls8962af
 - Add missing padding needed between address and data for SPI transfers.
men_z188
 - Fix iomap leak in error path.
st,lsm6dsx
 - Wait for setting time in oneshot reads to get a stable result.
ti,tsc2046
 - Prevent an array overflow.

* tag 'iio-fixes-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
  iio: imu: st_lsm6dsx: wait for settling time in st_lsm6dsx_read_oneshot
  iio: Fix error handling for PM
  iio: addac: ad74413r: correct comparator gpio getters mask usage
  iio: addac: ad74413r: use ngpio size when iterating over mask
  iio: addac: ad74413r: Do not reference negative array offsets
  iio: adc: men_z188_adc: Fix a resource leak in an error handling path
  iio: frequency: admv1013: remove the always true condition
  iio: accel: fxls8962af: add padding to regmap for SPI
  iio:imu:adis16480: fix buffering for devices with no burst mode
  iio: adc: ad7124: fix mask used for setting AIN_BUFP & AIN_BUFM bits
  iio: adc: tsc2046: fix memory corruption by preventing array overflow

drivers/iio/accel/bmc150-accel-core.c

@@ -1783,11 +1783,14 @@ int bmc150_accel_core_probe(struct device *dev, struct regmap *regmap, int irq,
 	ret = iio_device_register(indio_dev);
 	if (ret < 0) {
 		dev_err(dev, "Unable to register iio device\n");
-		goto err_trigger_unregister;
+		goto err_pm_cleanup;
 	}
 
 	return 0;
 
+err_pm_cleanup:
+	pm_runtime_dont_use_autosuspend(dev);
+	pm_runtime_disable(dev);
 err_trigger_unregister:
 	bmc150_accel_unregister_triggers(data, BMC150_ACCEL_TRIGGERS - 1);
 err_buffer_cleanup:

drivers/iio/accel/fxls8962af-core.c

@@ -173,12 +173,20 @@ struct fxls8962af_data {
 	u16 upper_thres;
 };
 
-const struct regmap_config fxls8962af_regmap_conf = {
+const struct regmap_config fxls8962af_i2c_regmap_conf = {
 	.reg_bits = 8,
 	.val_bits = 8,
 	.max_register = FXLS8962AF_MAX_REG,
 };
-EXPORT_SYMBOL_GPL(fxls8962af_regmap_conf);
+EXPORT_SYMBOL_GPL(fxls8962af_i2c_regmap_conf);
+
+const struct regmap_config fxls8962af_spi_regmap_conf = {
+	.reg_bits = 8,
+	.pad_bits = 8,
+	.val_bits = 8,
+	.max_register = FXLS8962AF_MAX_REG,
+};
+EXPORT_SYMBOL_GPL(fxls8962af_spi_regmap_conf);
 
 enum {
 	fxls8962af_idx_x,

drivers/iio/accel/fxls8962af-i2c.c

@@ -18,7 +18,7 @@ static int fxls8962af_probe(struct i2c_client *client)
 {
 	struct regmap *regmap;
 
-	regmap = devm_regmap_init_i2c(client, &fxls8962af_regmap_conf);
+	regmap = devm_regmap_init_i2c(client, &fxls8962af_i2c_regmap_conf);
 	if (IS_ERR(regmap)) {
 		dev_err(&client->dev, "Failed to initialize i2c regmap\n");
 		return PTR_ERR(regmap);

drivers/iio/accel/fxls8962af-spi.c

@@ -18,7 +18,7 @@ static int fxls8962af_probe(struct spi_device *spi)
 {
 	struct regmap *regmap;
 
-	regmap = devm_regmap_init_spi(spi, &fxls8962af_regmap_conf);
+	regmap = devm_regmap_init_spi(spi, &fxls8962af_spi_regmap_conf);
 	if (IS_ERR(regmap)) {
 		dev_err(&spi->dev, "Failed to initialize spi regmap\n");
 		return PTR_ERR(regmap);

drivers/iio/accel/fxls8962af.h

@@ -17,6 +17,7 @@ int fxls8962af_core_probe(struct device *dev, struct regmap *regmap, int irq);
 int fxls8962af_core_remove(struct device *dev);
 
 extern const struct dev_pm_ops fxls8962af_pm_ops;
-extern const struct regmap_config fxls8962af_regmap_conf;
+extern const struct regmap_config fxls8962af_i2c_regmap_conf;
+extern const struct regmap_config fxls8962af_spi_regmap_conf;
 
 #endif				/* _FXLS8962AF_H_ */

drivers/iio/accel/kxcjk-1013.c

@@ -1590,11 +1590,14 @@ static int kxcjk1013_probe(struct i2c_client *client,
 	ret = iio_device_register(indio_dev);
 	if (ret < 0) {
 		dev_err(&client->dev, "unable to register iio device\n");
-		goto err_buffer_cleanup;
+		goto err_pm_cleanup;
 	}
 
 	return 0;
 
+err_pm_cleanup:
+	pm_runtime_dont_use_autosuspend(&client->dev);
+	pm_runtime_disable(&client->dev);
 err_buffer_cleanup:
 	iio_triggered_buffer_cleanup(indio_dev);
 err_trigger_unregister:

drivers/iio/accel/mma9551.c

@@ -495,11 +495,14 @@ static int mma9551_probe(struct i2c_client *client,
 	ret = iio_device_register(indio_dev);
 	if (ret < 0) {
 		dev_err(&client->dev, "unable to register iio device\n");
-		goto out_poweroff;
+		goto err_pm_cleanup;
 	}
 
 	return 0;
 
+err_pm_cleanup:
+	pm_runtime_dont_use_autosuspend(&client->dev);
+	pm_runtime_disable(&client->dev);
 out_poweroff:
 	mma9551_set_device_state(client, false);
 

drivers/iio/accel/mma9553.c

@@ -1134,12 +1134,15 @@ static int mma9553_probe(struct i2c_client *client,
 	ret = iio_device_register(indio_dev);
 	if (ret < 0) {
 		dev_err(&client->dev, "unable to register iio device\n");
-		goto out_poweroff;
+		goto err_pm_cleanup;
 	}
 
 	dev_dbg(&indio_dev->dev, "Registered device %s\n", name);
 	return 0;
 
+err_pm_cleanup:
+	pm_runtime_dont_use_autosuspend(&client->dev);
+	pm_runtime_disable(&client->dev);
 out_poweroff:
 	mma9551_set_device_state(client, false);
 	return ret;

drivers/iio/adc/ad7124.c

@@ -76,7 +76,7 @@
 #define AD7124_CONFIG_REF_SEL(x)	FIELD_PREP(AD7124_CONFIG_REF_SEL_MSK, x)
 #define AD7124_CONFIG_PGA_MSK		GENMASK(2, 0)
 #define AD7124_CONFIG_PGA(x)		FIELD_PREP(AD7124_CONFIG_PGA_MSK, x)
-#define AD7124_CONFIG_IN_BUFF_MSK	GENMASK(7, 6)
+#define AD7124_CONFIG_IN_BUFF_MSK	GENMASK(6, 5)
 #define AD7124_CONFIG_IN_BUFF(x)	FIELD_PREP(AD7124_CONFIG_IN_BUFF_MSK, x)
 
 /* AD7124_FILTER_X */

drivers/iio/adc/men_z188_adc.c

@@ -103,6 +103,7 @@ static int men_z188_probe(struct mcb_device *dev,
 	struct z188_adc *adc;
 	struct iio_dev *indio_dev;
 	struct resource *mem;
+	int ret;
 
 	indio_dev = devm_iio_device_alloc(&dev->dev, sizeof(struct z188_adc));
 	if (!indio_dev)
@@ -128,8 +129,14 @@ static int men_z188_probe(struct mcb_device *dev,
 	adc->mem = mem;
 	mcb_set_drvdata(dev, indio_dev);
 
-	return iio_device_register(indio_dev);
+	ret = iio_device_register(indio_dev);
+	if (ret)
+		goto err_unmap;
+
+	return 0;
 
+err_unmap:
+	iounmap(adc->base);
 err:
 	mcb_release_mem(mem);
 	return -ENXIO;

drivers/iio/adc/ti-tsc2046.c

@@ -388,7 +388,7 @@ static int tsc2046_adc_update_scan_mode(struct iio_dev *indio_dev,
 	mutex_lock(&priv->slock);
 
 	size = 0;
-	for_each_set_bit(ch_idx, active_scan_mask, indio_dev->num_channels) {
+	for_each_set_bit(ch_idx, active_scan_mask, ARRAY_SIZE(priv->l)) {
 		size += tsc2046_adc_group_set_layout(priv, group, ch_idx);
 		tsc2046_adc_group_set_cmd(priv, group, ch_idx);
 		group++;
@@ -548,7 +548,7 @@ static int tsc2046_adc_setup_spi_msg(struct tsc2046_adc_priv *priv)
 	 * enabled.
 	 */
 	size = 0;
-	for (ch_idx = 0; ch_idx < priv->dcfg->num_channels; ch_idx++)
+	for (ch_idx = 0; ch_idx < ARRAY_SIZE(priv->l); ch_idx++)
 		size += tsc2046_adc_group_set_layout(priv, ch_idx, ch_idx);
 
 	priv->tx = devm_kzalloc(&priv->spi->dev, size, GFP_KERNEL);

drivers/iio/addac/ad74413r.c

@@ -134,7 +134,6 @@ struct ad74413r_state {
 #define AD74413R_CH_EN_MASK(x)		BIT(x)
 
 #define AD74413R_REG_DIN_COMP_OUT		0x25
-#define AD74413R_DIN_COMP_OUT_SHIFT_X(x)	x
 
 #define AD74413R_REG_ADC_RESULT_X(x)	(0x26 + (x))
 #define AD74413R_ADC_RESULT_MAX		GENMASK(15, 0)
@@ -288,7 +287,7 @@ static void ad74413r_gpio_set_multiple(struct gpio_chip *chip,
 	unsigned int offset = 0;
 	int ret;
 
-	for_each_set_bit_from(offset, mask, AD74413R_CHANNEL_MAX) {
+	for_each_set_bit_from(offset, mask, chip->ngpio) {
 		unsigned int real_offset = st->gpo_gpio_offsets[offset];
 
 		ret = ad74413r_set_gpo_config(st, real_offset,
@@ -316,7 +315,7 @@ static int ad74413r_gpio_get(struct gpio_chip *chip, unsigned int offset)
 	if (ret)
 		return ret;
 
-	status &= AD74413R_DIN_COMP_OUT_SHIFT_X(real_offset);
+	status &= BIT(real_offset);
 
 	return status ? 1 : 0;
 }
@@ -334,11 +333,10 @@ static int ad74413r_gpio_get_multiple(struct gpio_chip *chip,
 	if (ret)
 		return ret;
 
-	for_each_set_bit_from(offset, mask, AD74413R_CHANNEL_MAX) {
+	for_each_set_bit_from(offset, mask, chip->ngpio) {
 		unsigned int real_offset = st->comp_gpio_offsets[offset];
 
-		if (val & BIT(real_offset))
-			*bits |= offset;
+		__assign_bit(offset, bits, val & BIT(real_offset));
 	}
 
 	return ret;
@@ -840,7 +838,7 @@ static int ad74413r_update_scan_mode(struct iio_dev *indio_dev,
 {
 	struct ad74413r_state *st = iio_priv(indio_dev);
 	struct spi_transfer *xfer = st->adc_samples_xfer;
-	u8 *rx_buf = &st->adc_samples_buf.rx_buf[-1 * AD74413R_FRAME_SIZE];
+	u8 *rx_buf = st->adc_samples_buf.rx_buf;
 	u8 *tx_buf = st->adc_samples_tx_buf;
 	unsigned int channel;
 	int ret = -EINVAL;
@@ -894,9 +892,10 @@ static int ad74413r_update_scan_mode(struct iio_dev *indio_dev,
 
 		spi_message_add_tail(xfer, &st->adc_samples_msg);
 
-		xfer++;
 		tx_buf += AD74413R_FRAME_SIZE;
-		rx_buf += AD74413R_FRAME_SIZE;
+		if (xfer != st->adc_samples_xfer)
+			rx_buf += AD74413R_FRAME_SIZE;
+		xfer++;
 	}
 
 	xfer->rx_buf = rx_buf;

drivers/iio/frequency/admv1013.c

@@ -348,7 +348,7 @@ static int admv1013_update_mixer_vgate(struct admv1013_state *st)
 
 	vcm = regulator_get_voltage(st->reg);
 
-	if (vcm >= 0 && vcm < 1800000)
+	if (vcm < 1800000)
 		mixer_vgate = (2389 * vcm / 1000000 + 8100) / 100;
 	else if (vcm > 1800000 && vcm < 2600000)
 		mixer_vgate = (2375 * vcm / 1000000 + 125) / 100;

drivers/iio/gyro/bmg160_core.c

@@ -1188,11 +1188,14 @@ int bmg160_core_probe(struct device *dev, struct regmap *regmap, int irq,
 	ret = iio_device_register(indio_dev);
 	if (ret < 0) {
 		dev_err(dev, "unable to register iio device\n");
-		goto err_buffer_cleanup;
+		goto err_pm_cleanup;
 	}
 
 	return 0;
 
+err_pm_cleanup:
+	pm_runtime_dont_use_autosuspend(dev);
+	pm_runtime_disable(dev);
 err_buffer_cleanup:
 	iio_triggered_buffer_cleanup(indio_dev);
 err_trigger_unregister:

drivers/iio/imu/adis16480.c

@@ -1403,6 +1403,7 @@ static int adis16480_probe(struct spi_device *spi)
 {
 	const struct spi_device_id *id = spi_get_device_id(spi);
 	const struct adis_data *adis16480_data;
+	irq_handler_t trigger_handler = NULL;
 	struct iio_dev *indio_dev;
 	struct adis16480 *st;
 	int ret;
@@ -1474,8 +1475,12 @@ static int adis16480_probe(struct spi_device *spi)
 		st->clk_freq = st->chip_info->int_clk;
 	}
 
+	/* Only use our trigger handler if burst mode is supported */
+	if (adis16480_data->burst_len)
+		trigger_handler = adis16480_trigger_handler;
+
 	ret = devm_adis_setup_buffer_and_trigger(&st->adis, indio_dev,
-						 adis16480_trigger_handler);
+						 trigger_handler);
 	if (ret)
 		return ret;
 

drivers/iio/imu/kmx61.c

@@ -1385,7 +1385,7 @@ static int kmx61_probe(struct i2c_client *client,
 	ret = iio_device_register(data->acc_indio_dev);
 	if (ret < 0) {
 		dev_err(&client->dev, "Failed to register acc iio device\n");
-		goto err_buffer_cleanup_mag;
+		goto err_pm_cleanup;
 	}
 
 	ret = iio_device_register(data->mag_indio_dev);
@@ -1398,6 +1398,9 @@ static int kmx61_probe(struct i2c_client *client,
 
 err_iio_unregister_acc:
 	iio_device_unregister(data->acc_indio_dev);
+err_pm_cleanup:
+	pm_runtime_dont_use_autosuspend(&client->dev);
+	pm_runtime_disable(&client->dev);
 err_buffer_cleanup_mag:
 	if (client->irq > 0)
 		iio_triggered_buffer_cleanup(data->mag_indio_dev);

drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_core.c

@@ -1374,8 +1374,12 @@ static int st_lsm6dsx_read_oneshot(struct st_lsm6dsx_sensor *sensor,
 	if (err < 0)
 		return err;
 
+	/*
+	 * we need to wait for sensor settling time before
+	 * reading data in order to avoid corrupted samples
+	 */
 	delay = 1000000000 / sensor->odr;
-	usleep_range(delay, 2 * delay);
+	usleep_range(3 * delay, 4 * delay);
 
 	err = st_lsm6dsx_read_locked(hw, addr, &data, sizeof(data));
 	if (err < 0)

drivers/iio/magnetometer/bmc150_magn.c

@@ -962,13 +962,14 @@ int bmc150_magn_probe(struct device *dev, struct regmap *regmap,
 	ret = iio_device_register(indio_dev);
 	if (ret < 0) {
 		dev_err(dev, "unable to register iio device\n");
-		goto err_disable_runtime_pm;
+		goto err_pm_cleanup;
 	}
 
 	dev_dbg(dev, "Registered device %s\n", name);
 	return 0;
 
-err_disable_runtime_pm:
+err_pm_cleanup:
+	pm_runtime_dont_use_autosuspend(dev);
 	pm_runtime_disable(dev);
 err_buffer_cleanup:
 	iio_triggered_buffer_cleanup(indio_dev);