Merge tag 'imx-fixes-3.16' of...

Merge tag 'imx-fixes-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

Pull "i.MX fixes for 3.16" from Shawn Guo:

 - Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
   because controller base CD/WP is not working in esdhc driver due to
   runtime PM support
 - A couple of random ventana gw5xxx board fixes
 - Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
   IPUv3 driver out of staging tree
 - Fix enet/fec clock selection on imx6sl
 - Fix display node on imx53-m53evk board
 - A couple of Cubox-i updates from Russell, which were omitted from
   the merge window due to dependency

* tag 'imx-fixes-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: dts: imx51-eukrea-mbimxsd51-baseboard: unbreak esdhc.
  ARM: dts: imx51-babbage: Fix esdhc setup
  ARM: dts: mx5: Move the display out of soc {} node
  ARM: dts: mx5: Fix IPU port node placement
  ARM: imx_v6_v7_defconfig: Enable CONFIG_IMX_IPUV3_CORE
  ARM: dts: hummingboard/cubox-i: move usb otg configuration to platform level
  ARM: dts: cubox-i: add support for PWM-driven front panel LED
  ARM: dts: imx6: ventana: correct gw52xx sgtl5000 clock source
  ARM: dts: imx6qdl-gw5xxx: Fix Linear Technology vendor prefix
  ARM: dts: imx6: ventana: fix include typo
  ARM: dts: imx6sl: correct the fec ipg clock source
  ARM: imx6sl: add missing enet clock for imx6sl

arch/arm/boot/dts/imx51-babbage.dts

@@ -315,15 +315,15 @@ partition@40000 {
 &esdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1>;
-	fsl,cd-controller;
-	fsl,wp-controller;
+	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
 
 &esdhc2 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc2>;
-	cd-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+	cd-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
 	wp-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
 	status = "okay";
 };
@@ -468,8 +468,8 @@ MX51_PAD_SD1_DATA0__SD1_DATA0		0x20d5
 				MX51_PAD_SD1_DATA1__SD1_DATA1		0x20d5
 				MX51_PAD_SD1_DATA2__SD1_DATA2		0x20d5
 				MX51_PAD_SD1_DATA3__SD1_DATA3		0x20d5
-				MX51_PAD_GPIO1_0__SD1_CD		0x20d5
-				MX51_PAD_GPIO1_1__SD1_WP		0x20d5
+				MX51_PAD_GPIO1_0__GPIO1_0		0x100
+				MX51_PAD_GPIO1_1__GPIO1_1		0x100
 			>;
 		};
 

arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts

@@ -107,7 +107,7 @@ &audmux {
 &esdhc1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_esdhc1 &pinctrl_esdhc1_cd>;
-	fsl,cd-controller;
+	cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
 	status = "okay";
 };
 
@@ -206,7 +206,7 @@ MX51_PAD_DI1_D1_CS__GPIO3_4 0x1f5
 
 		pinctrl_esdhc1_cd: esdhc1_cd {
 			fsl,pins = <
-				MX51_PAD_GPIO1_0__SD1_CD 0x20d5
+				MX51_PAD_GPIO1_0__GPIO1_0 0xd5
 			>;
 		};
 

arch/arm/boot/dts/imx53-m53evk.dts

@@ -21,27 +21,25 @@ memory {
 		      <0xb0000000 0x20000000>;
 	};
 
-	soc {
-		display1: display@di1 {
-			compatible = "fsl,imx-parallel-display";
-			interface-pix-fmt = "bgr666";
-			pinctrl-names = "default";
-			pinctrl-0 = <&pinctrl_ipu_disp1>;
-
-			display-timings {
-				800x480p60 {
-					native-mode;
-					clock-frequency = <31500000>;
-					hactive = <800>;
-					vactive = <480>;
-					hfront-porch = <40>;
-					hback-porch = <88>;
-					hsync-len = <128>;
-					vback-porch = <33>;
-					vfront-porch = <9>;
-					vsync-len = <3>;
-					vsync-active = <1>;
-				};
+	display1: display@di1 {
+		compatible = "fsl,imx-parallel-display";
+		interface-pix-fmt = "bgr666";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ipu_disp1>;
+
+		display-timings {
+			800x480p60 {
+				native-mode;
+				clock-frequency = <31500000>;
+				hactive = <800>;
+				vactive = <480>;
+				hfront-porch = <40>;
+				hback-porch = <88>;
+				hsync-len = <128>;
+				vback-porch = <33>;
+				vfront-porch = <9>;
+				vsync-len = <3>;
+				vsync-active = <1>;
 			};
 		};
 

arch/arm/boot/dts/imx6dl-hummingboard.dts

@@ -143,6 +143,14 @@ pinctrl_hummingboard_usbh1_vbus: hummingboard-usbh1-vbus {
 			fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x1b0b0>;
 		};
 
+		pinctrl_hummingboard_usbotg_id: hummingboard-usbotg-id {
+			/*
+			 * Similar to pinctrl_usbotg_2, but we want it
+			 * pulled down for a fixed host connection.
+			 */
+			fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
+		};
+
 		pinctrl_hummingboard_usbotg_vbus: hummingboard-usbotg-vbus {
 			fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x1b0b0>;
 		};
@@ -178,6 +186,8 @@ &usbh1 {
 };
 
 &usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hummingboard_usbotg_id>;
 	vbus-supply = <&reg_usbotg_vbus>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6q-gw51xx.dts

@@ -11,7 +11,7 @@
 
 /dts-v1/;
 #include "imx6q.dtsi"
-#include "imx6qdl-gw54xx.dtsi"
+#include "imx6qdl-gw51xx.dtsi"
 
 / {
 	model = "Gateworks Ventana i.MX6 Quad GW51XX";

arch/arm/boot/dts/imx6qdl-cubox-i.dtsi

@@ -12,6 +12,19 @@ ir_recv: ir-receiver {
 		pinctrl-0 = <&pinctrl_cubox_i_ir>;
 	};
 
+	pwmleds {
+		compatible = "pwm-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_cubox_i_pwm1>;
+
+		front {
+			active-low;
+			label = "imx6:red:front";
+			max-brightness = <248>;
+			pwms = <&pwm1 0 50000>;
+		};
+	};
+
 	regulators {
 		compatible = "simple-bus";
 
@@ -109,6 +122,10 @@ MX6QDL_PAD_EIM_DA9__GPIO3_IO09 0x80000000
 			>;
 		};
 
+		pinctrl_cubox_i_pwm1: cubox-i-pwm1-front-led {
+			fsl,pins = <MX6QDL_PAD_DISP0_DAT8__PWM1_OUT 0x1b0b0>;
+		};
+
 		pinctrl_cubox_i_spdif: cubox-i-spdif {
 			fsl,pins = <MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x13091>;
 		};
@@ -117,6 +134,14 @@ pinctrl_cubox_i_usbh1_vbus: cubox-i-usbh1-vbus {
 			fsl,pins = <MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x4001b0b0>;
 		};
 
+		pinctrl_cubox_i_usbotg_id: cubox-i-usbotg-id {
+			/*
+			 * The Cubox-i pulls this low, but as it's pointless
+			 * leaving it as a pull-up, even if it is just 10uA.
+			 */
+			fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
+		};
+
 		pinctrl_cubox_i_usbotg_vbus: cubox-i-usbotg-vbus {
 			fsl,pins = <MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x4001b0b0>;
 		};
@@ -153,6 +178,8 @@ &usbh1 {
 };
 
 &usbotg {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cubox_i_usbotg_id>;
 	vbus-supply = <&reg_usbotg_vbus>;
 	status = "okay";
 };

arch/arm/boot/dts/imx6qdl-gw51xx.dtsi

@@ -161,7 +161,7 @@ &i2c2 {
 	status = "okay";
 
 	pmic: ltc3676@3c {
-		compatible = "ltc,ltc3676";
+		compatible = "lltc,ltc3676";
 		reg = <0x3c>;
 
 		regulators {

arch/arm/boot/dts/imx6qdl-gw52xx.dtsi

@@ -220,7 +220,7 @@ pciswitch: pex8609@3f {
 	};
 
 	pmic: ltc3676@3c {
-		compatible = "ltc,ltc3676";
+		compatible = "lltc,ltc3676";
 		reg = <0x3c>;
 
 		regulators {
@@ -288,7 +288,7 @@ accelerometer: fxos8700@1e {
 	codec: sgtl5000@0a {
 		compatible = "fsl,sgtl5000";
 		reg = <0x0a>;
-		clocks = <&clks 169>;
+		clocks = <&clks 201>;
 		VDDA-supply = <&reg_1p8v>;
 		VDDIO-supply = <&reg_3p3v>;
 	};

arch/arm/boot/dts/imx6qdl-gw53xx.dtsi

@@ -234,7 +234,7 @@ pciswitch: pex8606@3f {
 	};
 
 	pmic: ltc3676@3c {
-		compatible = "ltc,ltc3676";
+		compatible = "lltc,ltc3676";
 		reg = <0x3c>;
 
 		regulators {

arch/arm/boot/dts/imx6qdl-microsom.dtsi

@@ -10,14 +10,6 @@ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
 				MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA	0x1b0b1
 			>;
 		};
-
-		pinctrl_microsom_usbotg: microsom-usbotg {
-			/*
-			 * Similar to pinctrl_usbotg_2, but we want it
-			 * pulled down for a fixed host connection.
-			 */
-			fsl,pins = <MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x13059>;
-		};
 	};
 };
 
@@ -26,8 +18,3 @@ &uart1 {
 	pinctrl-0 = <&pinctrl_microsom_uart1>;
 	status = "okay";
 };
-
-&usbotg {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_microsom_usbotg>;
-};

arch/arm/boot/dts/imx6sl.dtsi

@@ -686,7 +686,7 @@ fec: ethernet@02188000 {
 				compatible = "fsl,imx6sl-fec", "fsl,imx25-fec";
 				reg = <0x02188000 0x4000>;
 				interrupts = <0 114 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clks IMX6SL_CLK_ENET_REF>,
+				clocks = <&clks IMX6SL_CLK_ENET>,
 					 <&clks IMX6SL_CLK_ENET_REF>;
 				clock-names = "ipg", "ahb";
 				status = "disabled";

arch/arm/configs/imx_v6_v7_defconfig

@@ -186,6 +186,7 @@ CONFIG_VIDEO_MX3=y
 CONFIG_V4L_MEM2MEM_DRIVERS=y
 CONFIG_VIDEO_CODA=y
 CONFIG_SOC_CAMERA_OV2640=y
+CONFIG_IMX_IPUV3_CORE=y
 CONFIG_DRM=y
 CONFIG_DRM_PANEL_SIMPLE=y
 CONFIG_BACKLIGHT_LCD_SUPPORT=y

arch/arm/mach-imx/clk-imx6sl.c

@@ -312,6 +312,7 @@ static void __init imx6sl_clocks_init(struct device_node *ccm_node)
 	clks[IMX6SL_CLK_ECSPI2]       = imx_clk_gate2("ecspi2",       "ecspi_root",        base + 0x6c, 2);
 	clks[IMX6SL_CLK_ECSPI3]       = imx_clk_gate2("ecspi3",       "ecspi_root",        base + 0x6c, 4);
 	clks[IMX6SL_CLK_ECSPI4]       = imx_clk_gate2("ecspi4",       "ecspi_root",        base + 0x6c, 6);
+	clks[IMX6SL_CLK_ENET]         = imx_clk_gate2("enet",         "ipg",               base + 0x6c, 10);
 	clks[IMX6SL_CLK_EPIT1]        = imx_clk_gate2("epit1",        "perclk",            base + 0x6c, 12);
 	clks[IMX6SL_CLK_EPIT2]        = imx_clk_gate2("epit2",        "perclk",            base + 0x6c, 14);
 	clks[IMX6SL_CLK_EXTERN_AUDIO] = imx_clk_gate2("extern_audio", "extern_audio_podf", base + 0x6c, 16);

include/dt-bindings/clock/imx6sl-clock.h

@@ -145,6 +145,7 @@
 #define IMX6SL_CLK_USDHC4		132
 #define IMX6SL_CLK_PLL4_AUDIO_DIV	133
 #define IMX6SL_CLK_SPBA			134
-#define IMX6SL_CLK_END			135
+#define IMX6SL_CLK_ENET			135
+#define IMX6SL_CLK_END			136
 
 #endif /* __DT_BINDINGS_CLOCK_IMX6SL_H */