Merge branch 'irqchip/broadcom' into irqchip/core

Conflicts:
	drivers/irqchip/Makefile

Documentation/devicetree/bindings/interrupt-controller/brcm,bcm7120-l2-intc.txt

+Broadcom BCM7120-style Level 2 interrupt controller
+
+This interrupt controller hardware is a second level interrupt controller that
+is hooked to a parent interrupt controller: e.g: ARM GIC for ARM-based
+platforms. It can be found on BCM7xxx products starting with BCM7120.
+
+Such an interrupt controller has the following hardware design:
+
+- outputs multiple interrupts signals towards its interrupt controller parent
+
+- controls how some of the interrupts will be flowing, whether they will
+  directly output an interrupt signal towards the interrupt controller parent,
+  or if they will output an interrupt signal at this 2nd level interrupt
+  controller, in particular for UARTs
+
+- not all 32-bits within the interrupt controller actually map to an interrupt
+
+The typical hardware layout for this controller is represented below:
+
+2nd level interrupt line		Outputs for the parent controller (e.g: ARM GIC)
+
+0 -----[ MUX ] ------------|==========> GIC interrupt 75
+          \-----------\
+                       |
+1 -----[ MUX ] --------)---|==========> GIC interrupt 76
+          \------------|
+                       |
+2 -----[ MUX ] --------)---|==========> GIC interrupt 77
+          \------------|
+                       |
+3 ---------------------|
+4 ---------------------|
+5 ---------------------|
+7 ---------------------|---|===========> GIC interrupt 66
+9 ---------------------|
+10 --------------------|
+11 --------------------/
+
+6 ------------------------\
+                           |===========> GIC interrupt 64
+8 ------------------------/
+
+12 ........................ X
+13 ........................ X 		(not connected)
+..
+31 ........................ X
+
+Required properties:
+
+- compatible: should be "brcm,bcm7120-l2-intc"
+- reg: specifies the base physical address and size of the registers
+- interrupt-controller: identifies the node as an interrupt controller
+- #interrupt-cells: specifies the number of cells needed to encode an interrupt
+  source, should be 1.
+- interrupt-parent: specifies the phandle to the parent interrupt controller
+  this one is cascaded from
+- interrupts: specifies the interrupt line(s) in the interrupt-parent controller
+  node, valid values depend on the type of parent interrupt controller
+- brcm,int-map-mask: 32-bits bit mask describing how many and which interrupts
+  are wired to this 2nd level interrupt controller, and how they match their
+  respective interrupt parents. Should match exactly the number of interrupts
+  specified in the 'interrupts' property.
+
+Optional properties:
+
+- brcm,irq-can-wake: if present, this means the L2 controller can be used as a
+  wakeup source for system suspend/resume.
+
+- brcm,int-fwd-mask: if present, a 32-bits bit mask to configure for the
+  interrupts which have a mux gate, typically UARTs. Setting these bits will
+  make their respective interrupts outputs bypass this 2nd level interrupt
+  controller completely, it completely transparent for the interrupt controller
+  parent
+
+Example:
+
+irq0_intc: interrupt-controller@f0406800 {
+	compatible = "brcm,bcm7120-l2-intc";
+	interrupt-parent = <&intc>;
+	#interrupt-cells = <1>;
+	reg = <0xf0406800 0x8>;
+	interrupt-controller;
+	interrupts = <0x0 0x42 0x0>, <0x0 0x40 0x0>;
+	brcm,int-map-mask = <0xeb8>, <0x140>;
+	brcm,int-fwd-mask = <0x7>;
+};

drivers/irqchip/Makefile

@@ -34,5 +34,6 @@ obj-$(CONFIG_TB10X_IRQC)		+= irq-tb10x.o
 obj-$(CONFIG_XTENSA)			+= irq-xtensa-pic.o
 obj-$(CONFIG_XTENSA_MX)			+= irq-xtensa-mx.o
 obj-$(CONFIG_IRQ_CROSSBAR)		+= irq-crossbar.o
-obj-$(CONFIG_BRCMSTB_L2_IRQ)		+= irq-brcmstb-l2.o
+obj-$(CONFIG_BRCMSTB_L2_IRQ)		+= irq-brcmstb-l2.o \
+					   irq-bcm7120-l2.o
 obj-$(CONFIG_KEYSTONE_IRQ)		+= irq-keystone.o

drivers/irqchip/irq-bcm7120-l2.c

+/*
+ * Broadcom BCM7120 style Level 2 interrupt controller driver
+ *
+ * Copyright (C) 2014 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#define pr_fmt(fmt)	KBUILD_MODNAME	": " fmt
+
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/io.h>
+#include <linux/irqdomain.h>
+#include <linux/reboot.h>
+#include <linux/irqchip/chained_irq.h>
+
+#include "irqchip.h"
+
+#include <asm/mach/irq.h>
+
+/* Register offset in the L2 interrupt controller */
+#define IRQEN		0x00
+#define IRQSTAT		0x04
+
+struct bcm7120_l2_intc_data {
+	void __iomem *base;
+	struct irq_domain *domain;
+	bool can_wake;
+	u32 irq_fwd_mask;
+	u32 irq_map_mask;
+	u32 saved_mask;
+};
+
+static void bcm7120_l2_intc_irq_handle(unsigned int irq, struct irq_desc *desc)
+{
+	struct bcm7120_l2_intc_data *b = irq_desc_get_handler_data(desc);
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+	u32 status;
+
+	chained_irq_enter(chip, desc);
+
+	status = __raw_readl(b->base + IRQSTAT);
+
+	if (status == 0) {
+		do_bad_IRQ(irq, desc);
+		goto out;
+	}
+
+	do {
+		irq = ffs(status) - 1;
+		status &= ~(1 << irq);
+		generic_handle_irq(irq_find_mapping(b->domain, irq));
+	} while (status);
+
+out:
+	chained_irq_exit(chip, desc);
+}
+
+static void bcm7120_l2_intc_suspend(struct irq_data *d)
+{
+	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
+	struct bcm7120_l2_intc_data *b = gc->private;
+	u32 reg;
+
+	irq_gc_lock(gc);
+	/* Save the current mask and the interrupt forward mask */
+	b->saved_mask = __raw_readl(b->base) | b->irq_fwd_mask;
+	if (b->can_wake) {
+		reg = b->saved_mask | gc->wake_active;
+		__raw_writel(reg, b->base);
+	}
+	irq_gc_unlock(gc);
+}
+
+static void bcm7120_l2_intc_resume(struct irq_data *d)
+{
+	struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
+	struct bcm7120_l2_intc_data *b = gc->private;
+
+	/* Restore the saved mask */
+	irq_gc_lock(gc);
+	__raw_writel(b->saved_mask, b->base);
+	irq_gc_unlock(gc);
+}
+
+static int bcm7120_l2_intc_init_one(struct device_node *dn,
+					struct bcm7120_l2_intc_data *data,
+					int irq, const __be32 *map_mask)
+{
+	int parent_irq;
+
+	parent_irq = irq_of_parse_and_map(dn, irq);
+	if (parent_irq < 0) {
+		pr_err("failed to map interrupt %d\n", irq);
+		return parent_irq;
+	}
+
+	data->irq_map_mask |= be32_to_cpup(map_mask + irq);
+
+	irq_set_handler_data(parent_irq, data);
+	irq_set_chained_handler(parent_irq, bcm7120_l2_intc_irq_handle);
+
+	return 0;
+}
+
+int __init bcm7120_l2_intc_of_init(struct device_node *dn,
+					struct device_node *parent)
+{
+	unsigned int clr = IRQ_NOREQUEST | IRQ_NOPROBE | IRQ_NOAUTOEN;
+	struct bcm7120_l2_intc_data *data;
+	struct irq_chip_generic *gc;
+	struct irq_chip_type *ct;
+	const __be32 *map_mask;
+	int num_parent_irqs;
+	int ret = 0, len, irq;
+
+	data = kzalloc(sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->base = of_iomap(dn, 0);
+	if (!data->base) {
+		pr_err("failed to remap intc L2 registers\n");
+		ret = -ENOMEM;
+		goto out_free;
+	}
+
+	if (of_property_read_u32(dn, "brcm,int-fwd-mask", &data->irq_fwd_mask))
+		data->irq_fwd_mask = 0;
+
+	/* Enable all interrupt specified in the interrupt forward mask and have
+	 * the other disabled
+	 */
+	__raw_writel(data->irq_fwd_mask, data->base + IRQEN);
+
+	num_parent_irqs = of_irq_count(dn);
+	if (num_parent_irqs <= 0) {
+		pr_err("invalid number of parent interrupts\n");
+		ret = -ENOMEM;
+		goto out_unmap;
+	}
+
+	map_mask = of_get_property(dn, "brcm,int-map-mask", &len);
+	if (!map_mask || (len != (sizeof(*map_mask) * num_parent_irqs))) {
+		pr_err("invalid brcm,int-map-mask property\n");
+		ret = -EINVAL;
+		goto out_unmap;
+	}
+
+	for (irq = 0; irq < num_parent_irqs; irq++) {
+		ret = bcm7120_l2_intc_init_one(dn, data, irq, map_mask);
+		if (ret)
+			goto out_unmap;
+	}
+
+	data->domain = irq_domain_add_linear(dn, 32,
+					&irq_generic_chip_ops, NULL);
+	if (!data->domain) {
+		ret = -ENOMEM;
+		goto out_unmap;
+	}
+
+	ret = irq_alloc_domain_generic_chips(data->domain, 32, 1,
+				dn->full_name, handle_level_irq, clr, 0,
+				IRQ_GC_INIT_MASK_CACHE);
+	if (ret) {
+		pr_err("failed to allocate generic irq chip\n");
+		goto out_free_domain;
+	}
+
+	gc = irq_get_domain_generic_chip(data->domain, 0);
+	gc->unused = 0xfffffff & ~data->irq_map_mask;
+	gc->reg_base = data->base;
+	gc->private = data;
+	ct = gc->chip_types;
+
+	ct->regs.mask = IRQEN;
+	ct->chip.irq_mask = irq_gc_mask_clr_bit;
+	ct->chip.irq_unmask = irq_gc_mask_set_bit;
+	ct->chip.irq_ack = irq_gc_noop;
+	ct->chip.irq_suspend = bcm7120_l2_intc_suspend;
+	ct->chip.irq_resume = bcm7120_l2_intc_resume;
+
+	if (of_property_read_bool(dn, "brcm,irq-can-wake")) {
+		data->can_wake = true;
+		/* This IRQ chip can wake the system, set all relevant child
+		 * interupts in wake_enabled mask
+		 */
+		gc->wake_enabled = 0xffffffff;
+		gc->wake_enabled &= ~gc->unused;
+		ct->chip.irq_set_wake = irq_gc_set_wake;
+	}
+
+	pr_info("registered BCM7120 L2 intc (mem: 0x%p, parent IRQ(s): %d)\n",
+			data->base, num_parent_irqs);
+
+	return 0;
+
+out_free_domain:
+	irq_domain_remove(data->domain);
+out_unmap:
+	iounmap(data->base);
+out_free:
+	kfree(data);
+	return ret;
+}
+IRQCHIP_DECLARE(brcmstb_l2_intc, "brcm,bcm7120-l2-intc",
+		bcm7120_l2_intc_of_init);