Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device tree changes from Arnd Bergmann:
 "A large part of the arm-soc patches are nowadays DT changes, adding
  support for new SoCs, boards and devices without changing kernel
  source.  The plan is still to move the devicetree files out of the
  kernel tree and reduce the amount of churn going on here, but we keep
  finding reasons to delay doing that.

  Changes are really all over the place, with little sticking out
  particularly.  We have contributions from a total of 116 people in
  this branch.

  Unfortunately, the size of this branch also causes a significant
  number of conflicts at the moment, typically when subsystem
  maintainers merge patches that change the driver at the same time as
  the dts files.  In most cases this could be avoided because the dts
  changes are supposed to be compatible in both ways, and we are asking
  everyone to send ARM dts changes through our tree only"

* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
  dts: stmmac: Document the clocks property in the stmmac base document
  dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
  ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
  ARM: STi: stih416: Add support for the FSM Serial Flash Controller
  ARM: tegra: fix Dalmore pinctrl configuration
  ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
  ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
  ARM: dts: Build all keystone dt blobs
  ARM: dts: keystone: Fix control register range for clktsip
  ARM: dts: keystone: Fix domain register range for clkfftc1
  ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
  ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
  ARM: dts: bcm21664: Add device tree files.
  ARM: DT: bcm21664: Device tree bindings
  ARM: efm32: properly namespace i2c location property
  ARM: efm32: fix unit address part in USART2 device nodes' names
  ARM: mvebu: Enable NAND controller in Armada 385-DB
  ARM: mvebu: Add support for NAND controller in Armada 38x SoC
  ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
  ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
  ...

Documentation/devicetree/bindings/arm/bcm/bcm21664.txt

+Broadcom BCM21664 device tree bindings
+--------------------------------------
+
+This document describes the device tree bindings for boards with the BCM21664
+SoC.
+
+Required root node property:
+  - compatible: brcm,bcm21664
+
+Example:
+	/ {
+		model = "BCM21664 SoC";
+		compatible = "brcm,bcm21664";
+		[...]
+	}

Documentation/devicetree/bindings/arm/bcm/kona-resetmgr.txt

+Broadcom Kona Family Reset Manager
+----------------------------------
+
+The reset manager is used on the Broadcom BCM21664 SoC.
+
+Required properties:
+  - compatible: brcm,bcm21664-resetmgr
+  - reg: memory address & range
+
+Example:
+	brcm,resetmgr@35001f00 {
+		compatible = "brcm,bcm21664-resetmgr";
+		reg = <0x35001f00 0x24>;
+	};

Documentation/devicetree/bindings/arm/keystone/keystone.txt

@@ -8,3 +8,13 @@ Required properties:
  - compatible: All TI specific devices present in Keystone SOC should be in
    the form "ti,keystone-*". Generic devices like gic, arch_timers, ns16550
    type UART should use the specified compatible for those devices.
+
+Boards:
+-  Keystone 2 Hawking/Kepler EVM
+   compatible = "ti,k2hk-evm","ti,keystone"
+
+-  Keystone 2 Lamarr EVM
+   compatible = "ti,k2l-evm","ti,keystone"
+
+-  Keystone 2 Edison EVM
+   compatible = "ti,k2e-evm","ti,keystone"

Documentation/devicetree/bindings/arm/omap/dmm.txt

+OMAP Dynamic Memory Manager (DMM) bindings
+
+The dynamic memory manager (DMM) is a module located immediately in front of the
+SDRAM controllers (called EMIFs on OMAP). DMM manages various aspects of memory
+accesses such as priority generation amongst initiators, configuration of SDRAM
+interleaving, optimizing transfer of 2D block objects, and provide MMU-like page
+translation for initiators which need contiguous dma bus addresses.
+
+Required properties:
+- compatible:	Should contain "ti,omap4-dmm" for OMAP4 family
+		Should contain "ti,omap5-dmm" for OMAP5 and DRA7x family
+- reg:		Contains DMM register address range (base address and length)
+- interrupts:	Should contain an interrupt-specifier for DMM_IRQ.
+- ti,hwmods:	Name of the hwmod associated to DMM, which is typically "dmm"
+
+Example:
+
+dmm@4e000000 {
+	compatible = "ti,omap4-dmm";
+	reg = <0x4e000000 0x800>;
+	ti,hwmods = "dmm";
+};

Documentation/devicetree/bindings/arm/omap/omap.txt

@@ -99,6 +99,9 @@ Boards:
 - OMAP4 PandaBoard : Low cost community board
   compatible = "ti,omap4-panda", "ti,omap4430"
 
+- OMAP4 DuoVero with Parlor : Commercial expansion board with daughter board
+  compatible = "gumstix,omap4-duovero-parlor", "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4";
+
 - OMAP3 EVM : Software Development Board for OMAP35x, AM/DM37x
   compatible = "ti,omap3-evm", "ti,omap3"
 
@@ -114,5 +117,8 @@ Boards:
 - AM43x EPOS EVM
   compatible = "ti,am43x-epos-evm", "ti,am4372", "ti,am43"
 
+- AM437x GP EVM
+  compatible = "ti,am437x-gp-evm", "ti,am4372", "ti,am43"
+
 - DRA7 EVM:  Software Developement Board for DRA7XX
   compatible = "ti,dra7-evm", "ti,dra7"

Documentation/devicetree/bindings/arm/samsung/pmu.txt

+SAMSUNG Exynos SoC series PMU Registers
+
+Properties:
+ - compatible : should contain two values. First value must be one from following list:
+		   - "samsung,exynos5250-pmu" - for Exynos5250 SoC,
+		   - "samsung,exynos5420-pmu" - for Exynos5420 SoC.
+		second value must be always "syscon".
+
+ - reg : offset and length of the register set.
+
+Example :
+pmu_system_controller: system-controller@10040000 {
+	compatible = "samsung,exynos5250-pmu", "syscon";
+	reg = <0x10040000 0x5000>;
+};

Documentation/devicetree/bindings/clock/exynos4-clock.txt

@@ -15,259 +15,12 @@ Required Properties:
 
 - #clock-cells: should be 1.
 
-The following is the list of clocks generated by the controller. Each clock is
-assigned an identifier and client nodes use this identifier to specify the
-clock which they consume. Some of the clocks are available only on a particular
-Exynos4 SoC and this is specified where applicable.
-
-
-		 [Core Clocks]
-
-  Clock               ID      SoC (if specific)
-  -----------------------------------------------
-
-  xxti                1
-  xusbxti             2
-  fin_pll             3
-  fout_apll           4
-  fout_mpll           5
-  fout_epll           6
-  fout_vpll           7
-  sclk_apll           8
-  sclk_mpll           9
-  sclk_epll           10
-  sclk_vpll           11
-  arm_clk             12
-  aclk200             13
-  aclk100             14
-  aclk160             15
-  aclk133             16
-  mout_mpll_user_t    17      Exynos4x12
-  mout_mpll_user_c    18      Exynos4x12
-  mout_core           19
-  mout_apll           20
-
-
-            [Clock Gate for Special Clocks]
-
-  Clock               ID      SoC (if specific)
-  -----------------------------------------------
-
-  sclk_fimc0          128
-  sclk_fimc1          129
-  sclk_fimc2          130
-  sclk_fimc3          131
-  sclk_cam0           132
-  sclk_cam1           133
-  sclk_csis0          134
-  sclk_csis1          135
-  sclk_hdmi           136
-  sclk_mixer          137
-  sclk_dac            138
-  sclk_pixel          139
-  sclk_fimd0          140
-  sclk_mdnie0         141     Exynos4412
-  sclk_mdnie_pwm0 12  142     Exynos4412
-  sclk_mipi0          143
-  sclk_audio0         144
-  sclk_mmc0           145
-  sclk_mmc1           146
-  sclk_mmc2           147
-  sclk_mmc3           148
-  sclk_mmc4           149
-  sclk_sata           150     Exynos4210
-  sclk_uart0          151
-  sclk_uart1          152
-  sclk_uart2          153
-  sclk_uart3          154
-  sclk_uart4          155
-  sclk_audio1         156
-  sclk_audio2         157
-  sclk_spdif          158
-  sclk_spi0           159
-  sclk_spi1           160
-  sclk_spi2           161
-  sclk_slimbus        162
-  sclk_fimd1          163     Exynos4210
-  sclk_mipi1          164     Exynos4210
-  sclk_pcm1           165
-  sclk_pcm2           166
-  sclk_i2s1           167
-  sclk_i2s2           168
-  sclk_mipihsi        169     Exynos4412
-  sclk_mfc            170
-  sclk_pcm0           171
-  sclk_g3d            172
-  sclk_pwm_isp        173     Exynos4x12
-  sclk_spi0_isp       174     Exynos4x12
-  sclk_spi1_isp       175     Exynos4x12
-  sclk_uart_isp       176     Exynos4x12
-  sclk_fimg2d         177
-
-	      [Peripheral Clock Gates]
-
-  Clock               ID      SoC (if specific)
-  -----------------------------------------------
-
-  fimc0               256
-  fimc1               257
-  fimc2               258
-  fimc3               259
-  csis0               260
-  csis1               261
-  jpeg                262
-  smmu_fimc0          263
-  smmu_fimc1          264
-  smmu_fimc2          265
-  smmu_fimc3          266
-  smmu_jpeg           267
-  vp                  268
-  mixer               269
-  tvenc               270     Exynos4210
-  hdmi                271
-  smmu_tv             272
-  mfc                 273
-  smmu_mfcl           274
-  smmu_mfcr           275
-  g3d                 276
-  g2d                 277
-  rotator             278     Exynos4210
-  mdma                279     Exynos4210
-  smmu_g2d            280     Exynos4210
-  smmu_rotator        281     Exynos4210
-  smmu_mdma           282     Exynos4210
-  fimd0               283
-  mie0                284
-  mdnie0              285     Exynos4412
-  dsim0               286
-  smmu_fimd0          287
-  fimd1               288     Exynos4210
-  mie1                289     Exynos4210
-  dsim1               290     Exynos4210
-  smmu_fimd1          291     Exynos4210
-  pdma0               292
-  pdma1               293
-  pcie_phy            294
-  sata_phy            295     Exynos4210
-  tsi                 296
-  sdmmc0              297
-  sdmmc1              298
-  sdmmc2              299
-  sdmmc3              300
-  sdmmc4              301
-  sata                302     Exynos4210
-  sromc               303
-  usb_host            304
-  usb_device          305
-  pcie                306
-  onenand             307
-  nfcon               308
-  smmu_pcie           309
-  gps                 310
-  smmu_gps            311
-  uart0               312
-  uart1               313
-  uart2               314
-  uart3               315
-  uart4               316
-  i2c0                317
-  i2c1                318
-  i2c2                319
-  i2c3                320
-  i2c4                321
-  i2c5                322
-  i2c6                323
-  i2c7                324
-  i2c_hdmi            325
-  tsadc               326
-  spi0                327
-  spi1                328
-  spi2                329
-  i2s1                330
-  i2s2                331
-  pcm0                332
-  i2s0                333
-  pcm1                334
-  pcm2                335
-  pwm                 336
-  slimbus             337
-  spdif               338
-  ac97                339
-  modemif             340
-  chipid              341
-  sysreg              342
-  hdmi_cec            343
-  mct                 344
-  wdt                 345
-  rtc                 346
-  keyif               347
-  audss               348
-  mipi_hsi            349     Exynos4210
-  mdma2               350     Exynos4210
-  pixelasyncm0        351
-  pixelasyncm1        352
-  fimc_lite0          353     Exynos4x12
-  fimc_lite1          354     Exynos4x12
-  ppmuispx            355     Exynos4x12
-  ppmuispmx           356     Exynos4x12
-  fimc_isp            357     Exynos4x12
-  fimc_drc            358     Exynos4x12
-  fimc_fd             359     Exynos4x12
-  mcuisp              360     Exynos4x12
-  gicisp              361     Exynos4x12
-  smmu_isp            362     Exynos4x12
-  smmu_drc            363     Exynos4x12
-  smmu_fd             364     Exynos4x12
-  smmu_lite0          365     Exynos4x12
-  smmu_lite1          366     Exynos4x12
-  mcuctl_isp          367     Exynos4x12
-  mpwm_isp            368     Exynos4x12
-  i2c0_isp            369     Exynos4x12
-  i2c1_isp            370     Exynos4x12
-  mtcadc_isp          371     Exynos4x12
-  pwm_isp             372     Exynos4x12
-  wdt_isp             373     Exynos4x12
-  uart_isp            374     Exynos4x12
-  asyncaxim           375     Exynos4x12
-  smmu_ispcx          376     Exynos4x12
-  spi0_isp            377     Exynos4x12
-  spi1_isp            378     Exynos4x12
-  pwm_isp_sclk        379     Exynos4x12
-  spi0_isp_sclk       380     Exynos4x12
-  spi1_isp_sclk       381     Exynos4x12
-  uart_isp_sclk       382     Exynos4x12
-  tmu_apbif           383
-
-		[Mux Clocks]
-
-  Clock			ID	SoC (if specific)
-  -----------------------------------------------
-
-  mout_fimc0		384
-  mout_fimc1		385
-  mout_fimc2		386
-  mout_fimc3		387
-  mout_cam0		388
-  mout_cam1		389
-  mout_csis0		390
-  mout_csis1		391
-  mout_g3d0		392
-  mout_g3d1		393
-  mout_g3d		394
-  aclk400_mcuisp	395	Exynos4x12
-
-		[Div Clocks]
-
-  Clock			ID	SoC (if specific)
-  -----------------------------------------------
-
-  div_isp0		450	Exynos4x12
-  div_isp1		451	Exynos4x12
-  div_mcuisp0		452	Exynos4x12
-  div_mcuisp1		453	Exynos4x12
-  div_aclk200		454	Exynos4x12
-  div_aclk400_mcuisp	455	Exynos4x12
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume.
 
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/exynos4.h header and can be used in device
+tree sources.
 
 Example 1: An example of a clock controller node is listed below.
 
@@ -285,6 +38,6 @@ Example 2: UART controller node that consumes the clock generated by the clock
 		compatible = "samsung,exynos4210-uart";
 		reg = <0x13820000 0x100>;
 		interrupts = <0 54 0>;
-		clocks = <&clock 314>, <&clock 153>;
+		clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
 		clock-names = "uart", "clk_uart_baud0";
 	};

Documentation/devicetree/bindings/clock/exynos5250-clock.txt

@@ -13,163 +13,12 @@ Required Properties:
 
 - #clock-cells: should be 1.
 
-The following is the list of clocks generated by the controller. Each clock is
-assigned an identifier and client nodes use this identifier to specify the
-clock which they consume.
-
-
-       [Core Clocks]
-
-  Clock			ID
-  ----------------------------
-
-  fin_pll		1
-
-  [Clock Gate for Special Clocks]
-
-  Clock			ID
-  ----------------------------
-
-  sclk_cam_bayer	128
-  sclk_cam0		129
-  sclk_cam1		130
-  sclk_gscl_wa		131
-  sclk_gscl_wb		132
-  sclk_fimd1		133
-  sclk_mipi1		134
-  sclk_dp		135
-  sclk_hdmi		136
-  sclk_pixel		137
-  sclk_audio0		138
-  sclk_mmc0		139
-  sclk_mmc1		140
-  sclk_mmc2		141
-  sclk_mmc3		142
-  sclk_sata		143
-  sclk_usb3		144
-  sclk_jpeg		145
-  sclk_uart0		146
-  sclk_uart1		147
-  sclk_uart2		148
-  sclk_uart3		149
-  sclk_pwm		150
-  sclk_audio1		151
-  sclk_audio2		152
-  sclk_spdif		153
-  sclk_spi0		154
-  sclk_spi1		155
-  sclk_spi2		156
-  div_i2s1		157
-  div_i2s2		158
-  sclk_hdmiphy		159
-  div_pcm0		160
-
-
-   [Peripheral Clock Gates]
-
-  Clock			ID
-  ----------------------------
-
-  gscl0			256
-  gscl1			257
-  gscl2			258
-  gscl3			259
-  gscl_wa		260
-  gscl_wb		261
-  smmu_gscl0		262
-  smmu_gscl1		263
-  smmu_gscl2		264
-  smmu_gscl3		265
-  mfc			266
-  smmu_mfcl		267
-  smmu_mfcr		268
-  rotator		269
-  jpeg			270
-  mdma1			271
-  smmu_rotator		272
-  smmu_jpeg		273
-  smmu_mdma1		274
-  pdma0			275
-  pdma1			276
-  sata			277
-  usbotg		278
-  mipi_hsi		279
-  sdmmc0		280
-  sdmmc1		281
-  sdmmc2		282
-  sdmmc3		283
-  sromc			284
-  usb2			285
-  usb3			286
-  sata_phyctrl		287
-  sata_phyi2c		288
-  uart0			289
-  uart1			290
-  uart2			291
-  uart3			292
-  uart4			293
-  i2c0			294
-  i2c1			295
-  i2c2			296
-  i2c3			297
-  i2c4			298
-  i2c5			299
-  i2c6			300
-  i2c7			301
-  i2c_hdmi		302
-  adc			303
-  spi0			304
-  spi1			305
-  spi2			306
-  i2s1			307
-  i2s2			308
-  pcm1			309
-  pcm2			310
-  pwm			311
-  spdif			312
-  ac97			313
-  hsi2c0		314
-  hsi2c1		315
-  hs12c2		316
-  hs12c3		317
-  chipid		318
-  sysreg		319
-  pmu			320
-  cmu_top		321
-  cmu_core		322
-  cmu_mem		323
-  tzpc0			324
-  tzpc1			325
-  tzpc2			326
-  tzpc3			327
-  tzpc4			328
-  tzpc5			329
-  tzpc6			330
-  tzpc7			331
-  tzpc8			332
-  tzpc9			333
-  hdmi_cec		334
-  mct			335
-  wdt			336
-  rtc			337
-  tmu			338
-  fimd1			339
-  mie1			340
-  dsim0			341
-  dp			342
-  mixer			343
-  hdmi			344
-  g2d			345
-  mdma0			346
-  smmu_mdma0		347
-
-
-   [Clock Muxes]
-
-  Clock			ID
-  ----------------------------
-  mout_hdmi		1024
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume.
 
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/exynos5250.h header and can be used in device
+tree sources.
 
 Example 1: An example of a clock controller node is listed below.
 
@@ -187,6 +36,6 @@ Example 2: UART controller node that consumes the clock generated by the clock
 		compatible = "samsung,exynos4210-uart";
 		reg = <0x13820000 0x100>;
 		interrupts = <0 54 0>;
-		clocks = <&clock 314>, <&clock 153>;
+		clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
 		clock-names = "uart", "clk_uart_baud0";
 	};

Documentation/devicetree/bindings/clock/exynos5420-clock.txt

@@ -13,184 +13,12 @@ Required Properties:
 
 - #clock-cells: should be 1.
 
-The following is the list of clocks generated by the controller. Each clock is
-assigned an identifier and client nodes use this identifier to specify the
-clock which they consume.
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume.
 
-
-       [Core Clocks]
-
-  Clock			ID
-  ----------------------------
-
-  fin_pll		1
-
-  [Clock Gate for Special Clocks]
-
-  Clock			ID
-  ----------------------------
-  sclk_uart0		128
-  sclk_uart1		129
-  sclk_uart2		130
-  sclk_uart3		131
-  sclk_mmc0		132
-  sclk_mmc1		133
-  sclk_mmc2		134
-  sclk_spi0		135
-  sclk_spi1		136
-  sclk_spi2		137
-  sclk_i2s1		138
-  sclk_i2s2		139
-  sclk_pcm1		140
-  sclk_pcm2		141
-  sclk_spdif		142
-  sclk_hdmi		143
-  sclk_pixel		144
-  sclk_dp1		145
-  sclk_mipi1		146
-  sclk_fimd1		147
-  sclk_maudio0		148
-  sclk_maupcm0		149
-  sclk_usbd300		150
-  sclk_usbd301		151
-  sclk_usbphy300	152
-  sclk_usbphy301	153
-  sclk_unipro		154
-  sclk_pwm		155
-  sclk_gscl_wa		156
-  sclk_gscl_wb		157
-  sclk_hdmiphy		158
-
-   [Peripheral Clock Gates]
-
-  Clock			ID
-  ----------------------------
-
-  aclk66_peric		256
-  uart0			257
-  uart1			258
-  uart2			259
-  uart3			260
-  i2c0			261
-  i2c1			262
-  i2c2			263
-  i2c3			264
-  i2c4			265
-  i2c5			266
-  i2c6			267
-  i2c7			268
-  i2c_hdmi		269
-  tsadc			270
-  spi0			271
-  spi1			272
-  spi2			273
-  keyif			274
-  i2s1			275
-  i2s2			276
-  pcm1			277
-  pcm2			278
-  pwm			279
-  spdif			280
-  i2c8			281
-  i2c9			282
-  i2c10			283
-  aclk66_psgen		300
-  chipid		301
-  sysreg		302
-  tzpc0			303
-  tzpc1			304
-  tzpc2			305
-  tzpc3			306
-  tzpc4			307
-  tzpc5			308
-  tzpc6			309
-  tzpc7			310
-  tzpc8			311
-  tzpc9			312
-  hdmi_cec		313
-  seckey		314
-  mct			315
-  wdt			316
-  rtc			317
-  tmu			318
-  tmu_gpu		319
-  pclk66_gpio		330
-  aclk200_fsys2		350
-  mmc0			351
-  mmc1			352
-  mmc2			353
-  sromc			354
-  ufs			355
-  aclk200_fsys		360
-  tsi			361
-  pdma0			362
-  pdma1			363
-  rtic			364
-  usbh20		365
-  usbd300		366
-  usbd301		377
-  aclk400_mscl		380
-  mscl0			381
-  mscl1			382
-  mscl2			383
-  smmu_mscl0		384
-  smmu_mscl1		385
-  smmu_mscl2		386
-  aclk333		400
-  mfc			401
-  smmu_mfcl		402
-  smmu_mfcr		403
-  aclk200_disp1		410
-  dsim1			411
-  dp1			412
-  hdmi			413
-  aclk300_disp1		420
-  fimd1			421
-  smmu_fimd1		422
-  aclk166		430
-  mixer			431
-  aclk266		440
-  rotator		441
-  mdma1			442
-  smmu_rotator		443
-  smmu_mdma1		444
-  aclk300_jpeg		450
-  jpeg			451
-  jpeg2			452
-  smmu_jpeg		453
-  aclk300_gscl		460
-  smmu_gscl0		461
-  smmu_gscl1		462
-  gscl_wa		463
-  gscl_wb		464
-  gscl0			465
-  gscl1			466
-  clk_3aa		467
-  aclk266_g2d		470
-  sss			471
-  slim_sss		472
-  mdma0			473
-  aclk333_g2d		480
-  g2d			481
-  aclk333_432_gscl	490
-  smmu_3aa		491
-  smmu_fimcl0		492
-  smmu_fimcl1		493
-  smmu_fimcl3		494
-  fimc_lite3		495
-  aclk_g3d		500
-  g3d			501
-  smmu_mixer		502
-
-  Mux			ID
-  ----------------------------
-
-  mout_hdmi		640
-
-  Divider		ID
-  ----------------------------
-
-  dout_pixel		768
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/exynos5420.h header and can be used in device
+tree sources.
 
 Example 1: An example of a clock controller node is listed below.
 
@@ -208,6 +36,6 @@ Example 2: UART controller node that consumes the clock generated by the clock
 		compatible = "samsung,exynos4210-uart";
 		reg = <0x13820000 0x100>;
 		interrupts = <0 54 0>;
-		clocks = <&clock 259>, <&clock 130>;
+		clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>;
 		clock-names = "uart", "clk_uart_baud0";
 	};

Documentation/devicetree/bindings/clock/exynos5440-clock.txt

@@ -12,45 +12,12 @@ Required Properties:
 
 - #clock-cells: should be 1.
 
-The following is the list of clocks generated by the controller. Each clock is
-assigned an identifier and client nodes use this identifier to specify the
-clock which they consume.
-
-
-       [Core Clocks]
-
-  Clock			ID
-  ----------------------------
-
-  xtal			1
-  arm_clk		2
-
-   [Peripheral Clock Gates]
-
-  Clock			ID
-  ----------------------------
-
-  spi_baud		16
-  pb0_250		17
-  pr0_250		18
-  pr1_250		19
-  b_250			20
-  b_125			21
-  b_200			22
-  sata			23
-  usb			24
-  gmac0			25
-  cs250			26
-  pb0_250_o		27
-  pr0_250_o		28
-  pr1_250_o		29
-  b_250_o		30
-  b_125_o		31
-  b_200_o		32
-  sata_o		33
-  usb_o			34
-  gmac0_o		35
-  cs250_o		36
+Each clock is assigned an identifier and client nodes can use this identifier
+to specify the clock which they consume.
+
+All available clocks are defined as preprocessor macros in
+dt-bindings/clock/exynos5440.h header and can be used in device
+tree sources.
 
 Example: An example of a clock controller node is listed below.
 

Documentation/devicetree/bindings/i2c/trivial-devices.txt

@@ -59,6 +59,7 @@ plx,pex8648		48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch
 ramtron,24c64		i2c serial eeprom  (24cxx)
 ricoh,rs5c372a		I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC
 samsung,24ad0xd1	S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power)
+sii,s35390a		2-wire CMOS real-time clock
 st-micro,24c256		i2c serial eeprom  (24cxx)
 stm,m41t00		Serial Access TIMEKEEPER
 stm,m41t62		Serial real-time clock (RTC) with alarm

Documentation/devicetree/bindings/arm/atmel-adc.txt → Documentation/devicetree/bindings/iio/adc/at91_adc.txt

@@ -8,32 +8,32 @@ Required properties:
   - clock-names: tuple listing input clock names.
 	Required elements: "adc_clk", "adc_op_clk".
   - clocks: phandles to input clocks.
-  - atmel,adc-channels-used: Bitmask of the channels muxed and enable for this
+  - atmel,adc-channels-used: Bitmask of the channels muxed and enabled for this
     device
   - atmel,adc-startup-time: Startup Time of the ADC in microseconds as
     defined in the datasheet
   - atmel,adc-vref: Reference voltage in millivolts for the conversions
-  - atmel,adc-res: List of resolution in bits supported by the ADC. List size
+  - atmel,adc-res: List of resolutions in bits supported by the ADC. List size
 		   must be two at least.
   - atmel,adc-res-names: Contains one identifier string for each resolution
 			 in atmel,adc-res property. "lowres" and "highres"
 			 identifiers are required.
 
 Optional properties:
-  - atmel,adc-use-external: Boolean to enable of external triggers
+  - atmel,adc-use-external-triggers: Boolean to enable the external triggers
   - atmel,adc-use-res: String corresponding to an identifier from
 		       atmel,adc-res-names property. If not specified, the highest
 		       resolution will be used.
   - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion
   - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds
-  - atmel,adc-ts-wires: Number of touch screen wires. Should be 4 or 5. If this
-                        value is set, then adc driver will enable touch screen
+  - atmel,adc-ts-wires: Number of touchscreen wires. Should be 4 or 5. If this
+                        value is set, then the adc driver will enable touchscreen
                         support.
-    NOTE: when adc touch screen enabled, the adc hardware trigger will be
-          disabled. Since touch screen will occupied the trigger register.
+    NOTE: when adc touchscreen is enabled, the adc hardware trigger will be
+          disabled. Since touchscreen will occupy the trigger register.
   - atmel,adc-ts-pressure-threshold: a pressure threshold for touchscreen. It
-                                     make touch detect more precision.
- 
+                                     makes touch detection more precise.
+
 Optional trigger Nodes:
   - Required properties:
     * trigger-name: Name of the trigger exposed to the user
@@ -44,42 +44,43 @@ Optional trigger Nodes:
 
 Examples:
 adc0: adc@fffb0000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
 	compatible = "atmel,at91sam9260-adc";
 	reg = <0xfffb0000 0x100>;
-	interrupts = <20 4>;
+	interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
 	clocks = <&adc_clk>, <&adc_op_clk>;
 	clock-names = "adc_clk", "adc_op_clk";
-	atmel,adc-channel-base = <0x30>;
 	atmel,adc-channels-used = <0xff>;
-	atmel,adc-drdy-mask = <0x10000>;
-	atmel,adc-num-channels = <8>;
 	atmel,adc-startup-time = <40>;
-	atmel,adc-status-register = <0x1c>;
-	atmel,adc-trigger-register = <0x08>;
-	atmel,adc-use-external;
+	atmel,adc-use-external-triggers;
 	atmel,adc-vref = <3300>;
 	atmel,adc-res = <8 10>;
 	atmel,adc-res-names = "lowres", "highres";
 	atmel,adc-use-res = "lowres";
 
 	trigger@0 {
+		reg = <0>;
 		trigger-name = "external-rising";
 		trigger-value = <0x1>;
 		trigger-external;
 	};
 	trigger@1 {
+		reg = <1>;
 		trigger-name = "external-falling";
 		trigger-value = <0x2>;
 		trigger-external;
 	};
 
 	trigger@2 {
+		reg = <2>;
 		trigger-name = "external-any";
 		trigger-value = <0x3>;
 		trigger-external;
 	};
 
 	trigger@3 {
+		reg = <3>;
 		trigger-name = "continuous";
 		trigger-value = <0x6>;
 	};

Documentation/devicetree/bindings/net/socfpga-dwmac.txt

+Altera SOCFPGA SoC DWMAC controller
+
+This is a variant of the dwmac/stmmac driver an inherits all descriptions
+present in Documentation/devicetree/bindings/net/stmmac.txt.
+
+The device node has additional properties:
+
+Required properties:
+ - compatible	: Should contain "altr,socfpga-stmmac" along with
+		  "snps,dwmac" and any applicable more detailed
+		  designware version numbers documented in stmmac.txt
+ - altr,sysmgr-syscon : Should be the phandle to the system manager node that
+   encompasses the glue register, the register offset, and the register shift.
+
+Example:
+
+gmac0: ethernet@ff700000 {
+	compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac";
+	altr,sysmgr-syscon = <&sysmgr 0x60 0>;
+	status = "disabled";
+	reg = <0xff700000 0x2000>;
+	interrupts = <0 115 4>;
+	interrupt-names = "macirq";
+	mac-address = [00 00 00 00 00 00];/* Filled in by U-Boot */
+	clocks = <&emac_0_clk>;
+	clocks-names = "stmmaceth";
+};

Documentation/devicetree/bindings/net/stmmac.txt

@@ -31,6 +31,10 @@ Optional properties:
 - reset-names: Should contain the reset signal name "stmmaceth", if a
 	reset phandle is given
 - max-frame-size: See ethernet.txt file in the same directory
+- clocks: If present, the first clock should be the GMAC main clock,
+  further clocks may be specified in derived bindings.
+- clocks-names: One name for each entry in the clocks property, the
+  first one should be "stmmaceth".
 
 Examples:
 
@@ -43,4 +47,6 @@ Examples:
 		mac-address = [000000000000]; /* Filled in by U-Boot */
 		max-frame-size = <3800>;
 		phy-mode = "gmii";
+		clocks = <&clock>;
+		clock-names = "stmmaceth">;
 	};

Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt

@@ -42,6 +42,10 @@ Required properties:
     - 0xc2000000: prefetchable memory region
   Please refer to the standard PCI bus binding document for a more detailed
   explanation.
+- #interrupt-cells: Size representation for interrupts (must be 1)
+- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
+  Please refer to the standard PCI bus binding document for a more detailed
+  explanation.
 - clocks: Must contain an entry for each entry in clock-names.
   See ../clocks/clock-bindings.txt for details.
 - clock-names: Must include the following entries:
@@ -86,6 +90,10 @@ SoC DTSI:
 		              0 99 0x04>; /* MSI interrupt */
 		interrupt-names = "intr", "msi";
 
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+
 		bus-range = <0x00 0xff>;
 		#address-cells = <3>;
 		#size-cells = <2>;

Documentation/devicetree/bindings/reset/st,sti-powerdown.txt

+STMicroelectronics STi family Sysconfig Peripheral Powerdown Reset Controller
+=============================================================================
+
+This binding describes a reset controller device that is used to enable and
+disable on-chip peripheral controllers such as USB and SATA, using
+"powerdown" control bits found in the STi family SoC system configuration
+registers. These have been grouped together into a single reset controller
+device for convenience.
+
+The actual action taken when powerdown is asserted is hardware dependent.
+However, when asserted it may not be possible to access the hardware's
+registers and after an assert/deassert sequence the hardware's previous state
+may no longer be valid.
+
+Please refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "st,<chip>-powerdown"
+	ex: "st,stih415-powerdown", "st,stih416-powerdown"
+- #reset-cells: 1, see below
+
+example:
+
+	powerdown: powerdown-controller {
+		#reset-cells = <1>;
+		compatible = "st,stih415-powerdown";
+	};
+
+
+Specifying powerdown control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the powerdown device node and an
+index specifying which channel to use, as described in reset.txt
+
+example:
+
+	usb1: usb@fe200000 {
+		resets	= <&powerdown STIH41X_USB1_POWERDOWN>;
+	};
+
+Macro definitions for the supported reset channels can be found in:
+
+include/dt-bindings/reset-controller/stih415-resets.h
+include/dt-bindings/reset-controller/stih416-resets.h

Documentation/devicetree/bindings/reset/st,sti-softreset.txt

+STMicroelectronics STi family Sysconfig Peripheral SoftReset Controller
+=============================================================================
+
+This binding describes a reset controller device that is used to enable and
+disable on-chip peripheral controllers such as USB and SATA, using
+"softreset" control bits found in the STi family SoC system configuration
+registers.
+
+The actual action taken when softreset is asserted is hardware dependent.
+However, when asserted it may not be possible to access the hardware's
+registers and after an assert/deassert sequence the hardware's previous state
+may no longer be valid.
+
+Please refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "st,<chip>-softreset" example:
+	"st,stih415-softreset" or "st,stih416-softreset";
+- #reset-cells: 1, see below
+
+example:
+
+	softreset: softreset-controller {
+		#reset-cells = <1>;
+		compatible = "st,stih415-softreset";
+	};
+
+
+Specifying softreset control of devices
+=======================================
+
+Device nodes should specify the reset channel required in their "resets"
+property, containing a phandle to the softreset device node and an
+index specifying which channel to use, as described in reset.txt
+
+example:
+
+	ethernet0{
+		resets			= <&softreset STIH415_ETH0_SOFTRESET>;
+	};
+
+Macro definitions for the supported reset channels can be found in:
+
+include/dt-bindings/reset-controller/stih415-resets.h
+include/dt-bindings/reset-controller/stih416-resets.h

Documentation/devicetree/bindings/usb/atmel-usb.txt

@@ -57,8 +57,8 @@ Required properties:
  - ep childnode: To specify the number of endpoints and their properties.
 
 Optional properties:
- - atmel,vbus-gpio: If present, specifies a gpio that needs to be
-   activated for the bus to be powered.
+ - atmel,vbus-gpio: If present, specifies a gpio that allows to detect whether
+   vbus is present (USB is connected).
 
 Required child node properties:
  - name: Name of the endpoint.

Documentation/devicetree/bindings/usb/ehci-omap.txt

@@ -21,7 +21,7 @@ Documentation/devicetree/bindings/mfd/omap-usb-host.txt
 Example for OMAP4:
 
 usbhsehci: ehci@4a064c00 {
-	compatible = "ti,ehci-omap", "usb-ehci";
+	compatible = "ti,ehci-omap";
 	reg = <0x4a064c00 0x400>;
 	interrupts = <0 77 0x4>;
 };

Documentation/devicetree/bindings/usb/ohci-omap3.txt

@@ -9,7 +9,7 @@ Required properties:
 Example for OMAP4:
 
 usbhsohci: ohci@4a064800 {
-	compatible = "ti,ohci-omap3", "usb-ohci";
+	compatible = "ti,ohci-omap3";
 	reg = <0x4a064800 0x400>;
 	interrupts = <0 76 0x4>;
 };

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -35,11 +35,13 @@ dallas	Maxim Integrated Products (formerly Dallas Semiconductor)
 davicom	DAVICOM Semiconductor, Inc.
 dlink	D-Link Systems, Inc.
 denx	Denx Software Engineering
+dmo	Data Modul AG
 edt	Emerging Display Technologies
 emmicro	EM Microelectronic
 epfl	Ecole Polytechnique Fédérale de Lausanne
 epson	Seiko Epson Corp.
 est	ESTeem Wireless Modems
+eukrea  Eukréa Electromatique
 fsl	Freescale Semiconductor
 GEFanuc	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
 gef	GE Fanuc Intelligent Platforms Embedded Systems, Inc.
@@ -83,10 +85,12 @@ picochip	Picochip Ltd
 powervr	PowerVR (deprecated, use img)
 qca	Qualcomm Atheros, Inc.
 qcom	Qualcomm Technologies, Inc
+qnap	QNAP Systems, Inc.
 ralink	Mediatek/Ralink Technology Corp.
 ramtron	Ramtron International
 realtek Realtek Semiconductor Corp.
 renesas	Renesas Electronics Corporation
+ricoh	Ricoh Co. Ltd.
 rockchip	Fuzhou Rockchip Electronics Co., Ltd
 samsung	Samsung Semiconductor
 sbs	Smart Battery System
@@ -94,6 +98,7 @@ schindler	Schindler
 sil	Silicon Image
 silabs	Silicon Laboratories
 simtek
+sii	Seiko Instruments, Inc.
 sirf	SiRF Technology, Inc.
 smsc	Standard Microsystems Corporation
 snps 	Synopsys, Inc.
@@ -101,12 +106,14 @@ spansion	Spansion Inc.
 st	STMicroelectronics
 ste	ST-Ericsson
 stericsson	ST-Ericsson
+synology	Synology, Inc.
 ti	Texas Instruments
 tlm	Trusted Logic Mobility
 toshiba	Toshiba Corporation
 toumaz	Toumaz
 v3	V3 Semiconductor
 via	VIA Technologies, Inc.
+voipac	Voipac Technologies s.r.o.
 winbond Winbond Electronics corp.
 wlf	Wolfson Microelectronics
 wm	Wondermedia Technologies, Inc.

arch/arm/boot/dts/Makefile

@@ -51,19 +51,15 @@ dtb-$(CONFIG_ARCH_AT91)	+= sama5d36ek.dtb
 
 dtb-$(CONFIG_ARCH_ATLAS6) += atlas6-evb.dtb
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb
-dtb-$(CONFIG_ARCH_BCM_MOBILE) += bcm11351-brt.dtb \
-	bcm28155-ap.dtb
+dtb-$(CONFIG_ARCH_BCM_MOBILE) += bcm28155-ap.dtb \
+	bcm21664-garnet.dtb
 dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb
+dtb-$(CONFIG_ARCH_BCM_5301X) += bcm4708-netgear-r6250.dtb
 dtb-$(CONFIG_ARCH_BERLIN) += \
 	berlin2-sony-nsz-gs7.dtb	\
 	berlin2cd-google-chromecast.dtb
 dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \
 	da850-evm.dtb
-dtb-$(CONFIG_MACH_DOVE) += dove-cm-a510.dtb \
-	dove-cubox.dtb \
-	dove-d2plug.dtb \
-	dove-d3plug.dtb \
-	dove-dove-db.dtb
 dtb-$(CONFIG_ARCH_EFM32) += efm32gg-dk3750.dtb
 dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos4210-smdkv310.dtb \
@@ -86,7 +82,11 @@ dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb \
 	ecx-2000.dtb
 dtb-$(CONFIG_ARCH_INTEGRATOR) += integratorap.dtb \
 	integratorcp.dtb
+dtb-$(CONFIG_ARCH_KEYSTONE) += k2hk-evm.dtb \
+	k2l-evm.dtb \
+	k2e-evm.dtb
 kirkwood := \
+	kirkwood-b3.dtb \
 	kirkwood-cloudbox.dtb \
 	kirkwood-db-88f6281.dtb \
 	kirkwood-db-88f6282.dtb \
@@ -94,6 +94,18 @@ kirkwood := \
 	kirkwood-dns325.dtb \
 	kirkwood-dockstar.dtb \
 	kirkwood-dreamplug.dtb \
+	kirkwood-ds109.dtb \
+	kirkwood-ds110jv10.dtb \
+	kirkwood-ds111.dtb \
+	kirkwood-ds209.dtb \
+	kirkwood-ds210.dtb \
+	kirkwood-ds212.dtb \
+	kirkwood-ds212j.dtb \
+	kirkwood-ds409.dtb \
+	kirkwood-ds409slim.dtb \
+	kirkwood-ds411.dtb \
+	kirkwood-ds411j.dtb \
+	kirkwood-ds411slim.dtb \
 	kirkwood-goflexnet.dtb \
 	kirkwood-guruplug-server-plus.dtb \
 	kirkwood-ib62x0.dtb \
@@ -116,54 +128,74 @@ kirkwood := \
 	kirkwood-nsa310a.dtb \
 	kirkwood-openblocks_a6.dtb \
 	kirkwood-openblocks_a7.dtb \
+	kirkwood-rd88f6192.dtb \
+	kirkwood-rd88f6281-a0.dtb \
+	kirkwood-rd88f6281-a1.dtb \
+	kirkwood-rs212.dtb \
+	kirkwood-rs409.dtb \
+	kirkwood-rs411.dtb \
 	kirkwood-sheevaplug.dtb \
 	kirkwood-sheevaplug-esata.dtb \
+	kirkwood-t5325.dtb \
 	kirkwood-topkick.dtb \
 	kirkwood-ts219-6281.dtb \
-	kirkwood-ts219-6282.dtb
+	kirkwood-ts219-6282.dtb \
+	kirkwood-ts419-6281.dtb \
+	kirkwood-ts419-6282.dtb
 dtb-$(CONFIG_ARCH_KIRKWOOD) += $(kirkwood)
 dtb-$(CONFIG_MACH_KIRKWOOD) += $(kirkwood)
 dtb-$(CONFIG_ARCH_LPC32XX) += ea3250.dtb phy3250.dtb
 dtb-$(CONFIG_ARCH_MARCO) += marco-evb.dtb
 dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb
-dtb-$(CONFIG_ARCH_MVEBU) += armada-370-db.dtb \
-	armada-370-mirabox.dtb \
-	armada-370-netgear-rn102.dtb \
-	armada-370-netgear-rn104.dtb \
-	armada-370-rd.dtb \
-	armada-xp-axpwifiap.dtb \
-	armada-xp-db.dtb \
-	armada-xp-gp.dtb \
-	armada-xp-netgear-rn2120.dtb \
-	armada-xp-matrix.dtb \
-	armada-xp-openblocks-ax3-4.dtb
 dtb-$(CONFIG_ARCH_MXC) += \
+	imx25-eukrea-mbimxsd25-baseboard.dtb \
 	imx25-karo-tx25.dtb \
 	imx25-pdk.dtb \
 	imx27-apf27.dtb \
 	imx27-apf27dev.dtb \
 	imx27-pdk.dtb \
-	imx27-phytec-phycore-som.dtb \
 	imx27-phytec-phycore-rdk.dtb \
-	imx27-phytec-phycard-s-som.dtb \
 	imx27-phytec-phycard-s-rdk.dtb \
 	imx31-bug.dtb \
+	imx35-eukrea-mbimxsd35-baseboard.dtb \
+	imx50-evk.dtb \
 	imx51-apf51.dtb \
 	imx51-apf51dev.dtb \
 	imx51-babbage.dtb \
+	imx51-eukrea-mbimxsd51-baseboard.dtb \
 	imx53-ard.dtb \
-	imx53-evk.dtb \
 	imx53-m53evk.dtb \
 	imx53-mba53.dtb \
 	imx53-qsb.dtb \
+	imx53-qsrb.dtb \
 	imx53-smd.dtb \
+	imx53-tx53-x03x.dtb \
+	imx53-tx53-x13x.dtb \
+	imx53-voipac-bsb.dtb \
 	imx6dl-cubox-i.dtb \
+	imx6dl-dfi-fs700-m60.dtb \
+	imx6dl-gw51xx.dtb \
+	imx6dl-gw52xx.dtb \
+	imx6dl-gw53xx.dtb \
+	imx6dl-gw54xx.dtb \
 	imx6dl-hummingboard.dtb \
+	imx6dl-nitrogen6x.dtb \
 	imx6dl-sabreauto.dtb \
+	imx6dl-sabrelite.dtb \
 	imx6dl-sabresd.dtb \
 	imx6dl-wandboard.dtb \
 	imx6q-arm2.dtb \
+	imx6q-cm-fx6.dtb \
 	imx6q-cubox-i.dtb \
+	imx6q-dfi-fs700-m60.dtb \
+	imx6q-dmo-edmqmx6.dtb \
+	imx6q-gk802.dtb \
+	imx6q-gw51xx.dtb \
+	imx6q-gw52xx.dtb \
+	imx6q-gw53xx.dtb \
+	imx6q-gw5400-a.dtb \
+	imx6q-gw54xx.dtb \
+	imx6q-nitrogen6x.dtb \
 	imx6q-phytec-pbab01.dtb \
 	imx6q-sabreauto.dtb \
 	imx6q-sabrelite.dtb \
@@ -187,6 +219,9 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \
 	imx28-cfa10056.dtb \
 	imx28-cfa10057.dtb \
 	imx28-cfa10058.dtb \
+	imx28-duckbill.dtb \
+	imx28-eukrea-mbmx283lc.dtb \
+	imx28-eukrea-mbmx287lc.dtb \
 	imx28-evk.dtb \
 	imx28-m28cu3.dtb \
 	imx28-m28evk.dtb \
@@ -203,6 +238,10 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap2420-n810-wimax.dtb \
 	omap3430-sdp.dtb \
 	omap3-beagle.dtb \
+	omap3-cm-t3517.dtb \
+	omap3-sbc-t3517.dtb \
+	omap3-cm-t3530.dtb \
+	omap3-sbc-t3530.dtb \
 	omap3-cm-t3730.dtb \
 	omap3-sbc-t3730.dtb \
 	omap3-devkit8000.dtb \
@@ -213,12 +252,24 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap3-n900.dtb \
 	omap3-n9.dtb \
 	omap3-n950.dtb \
+	omap3-overo-alto35.dtb \
+	omap3-overo-storm-alto35.dtb \
+	omap3-overo-chestnut43.dtb \
+	omap3-overo-storm-chestnut43.dtb \
+	omap3-overo-gallop43.dtb \
+	omap3-overo-storm-gallop43.dtb \
+	omap3-overo-palo43.dtb \
+	omap3-overo-storm-palo43.dtb \
+	omap3-overo-summit.dtb \
+	omap3-overo-storm-summit.dtb \
 	omap3-overo-tobi.dtb \
 	omap3-overo-storm-tobi.dtb \
 	omap3-gta04.dtb \
 	omap3-igep0020.dtb \
 	omap3-igep0030.dtb \
+	omap3-lilly-dbb056.dtb \
 	omap3-zoom3.dtb \
+	omap4-duovero-parlor.dtb \
 	omap4-panda.dtb \
 	omap4-panda-a4.dtb \
 	omap4-panda-es.dtb \
@@ -232,9 +283,11 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	am335x-boneblack.dtb \
 	am335x-nano.dtb \
 	am335x-base0033.dtb \
+	am3517-craneboard.dtb \
 	am3517-evm.dtb \
 	am3517_mt_ventoux.dtb \
 	am43x-epos-evm.dtb \
+	am437x-gp-evm.dtb \
 	dra7-evm.dtb
 dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb
 dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb
@@ -291,6 +344,9 @@ dtb-$(CONFIG_ARCH_SUNXI) += \
 	sun4i-a10-cubieboard.dtb \
 	sun4i-a10-mini-xplus.dtb \
 	sun4i-a10-hackberry.dtb \
+	sun4i-a10-inet97fv2.dtb \
+	sun4i-a10-olinuxino-lime.dtb \
+	sun4i-a10-pcduino.dtb \
 	sun5i-a10s-olinuxino-micro.dtb \
 	sun5i-a13-olinuxino.dtb \
 	sun5i-a13-olinuxino-micro.dtb \
@@ -329,6 +385,29 @@ dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \
 dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \
 	zynq-zc706.dtb \
 	zynq-zed.dtb
+dtb-$(CONFIG_MACH_ARMADA_370) += \
+	armada-370-db.dtb \
+	armada-370-mirabox.dtb \
+	armada-370-netgear-rn102.dtb \
+	armada-370-netgear-rn104.dtb \
+	armada-370-rd.dtb
+dtb-$(CONFIG_MACH_ARMADA_375) += \
+	armada-375-db.dtb
+dtb-$(CONFIG_MACH_ARMADA_38X) += \
+	armada-385-db.dtb \
+	armada-385-rd.dtb
+dtb-$(CONFIG_MACH_ARMADA_XP) += \
+	armada-xp-axpwifiap.dtb \
+	armada-xp-db.dtb \
+	armada-xp-gp.dtb \
+	armada-xp-netgear-rn2120.dtb \
+	armada-xp-matrix.dtb \
+	armada-xp-openblocks-ax3-4.dtb
+dtb-$(CONFIG_MACH_DOVE) += dove-cm-a510.dtb \
+	dove-cubox.dtb \
+	dove-d2plug.dtb \
+	dove-d3plug.dtb \
+	dove-dove-db.dtb
 
 targets += dtbs dtbs_install
 targets += $(dtb-y)

arch/arm/boot/dts/am335x-evm.dts

@@ -260,6 +260,12 @@ davinci_mdio_sleep: davinci_mdio_sleep {
 		>;
 	};
 
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
+		>;
+	};
+
 	lcd_pins_s0: lcd_pins_s0 {
 		pinctrl-single,pins = <
 			0x20 0x01	/* gpmc_ad8.lcd_data16, OUTPUT | MODE1 */
@@ -434,9 +440,9 @@ &gpmc {
 	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
 	nand@0,0 {
 		reg = <0 0 0>; /* CS0, offset 0 */
-		nand-bus-width = <8>;
 		ti,nand-ecc-opt = "bch8";
-		gpmc,device-nand = "true";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
 		gpmc,device-width = <1>;
 		gpmc,sync-clk-ps = <0>;
 		gpmc,cs-on-ns = <0>;
@@ -460,50 +466,51 @@ nand@0,0 {
 		gpmc,wait-monitoring-ns = <0>;
 		gpmc,wr-access-ns = <40>;
 		gpmc,wr-data-mux-bus-ns = <0>;
-
+		/* MTD partition table */
+		/* All SPL-* partitions are sized to minimal length
+		 * which can be independently programmable. For
+		 * NAND flash this is equal to size of erase-block */
 		#address-cells = <1>;
 		#size-cells = <1>;
-		elm_id = <&elm>;
-
-		/* MTD partition table */
 		partition@0 {
-			label = "SPL1";
+			label = "NAND.SPL";
 			reg = <0x00000000 0x000020000>;
 		};
-
 		partition@1 {
-			label = "SPL2";
+			label = "NAND.SPL.backup1";
 			reg = <0x00020000 0x00020000>;
 		};
-
 		partition@2 {
-			label = "SPL3";
+			label = "NAND.SPL.backup2";
 			reg = <0x00040000 0x00020000>;
 		};
-
 		partition@3 {
-			label = "SPL4";
+			label = "NAND.SPL.backup3";
 			reg = <0x00060000 0x00020000>;
 		};
-
 		partition@4 {
-			label = "U-boot";
-			reg = <0x00080000 0x001e0000>;
+			label = "NAND.u-boot-spl";
+			reg = <0x00080000 0x00040000>;
 		};
-
 		partition@5 {
-			label = "environment";
-			reg = <0x00260000 0x00020000>;
+			label = "NAND.u-boot";
+			reg = <0x000C0000 0x00100000>;
 		};
-
 		partition@6 {
-			label = "Kernel";
-			reg = <0x00280000 0x00500000>;
+			label = "NAND.u-boot-env";
+			reg = <0x001C0000 0x00020000>;
 		};
-
 		partition@7 {
-			label = "File-System";
-			reg = <0x00780000 0x0F880000>;
+			label = "NAND.u-boot-env.backup1";
+			reg = <0x001E0000 0x00020000>;
+		};
+		partition@8 {
+			label = "NAND.kernel";
+			reg = <0x00200000 0x00800000>;
+		};
+		partition@9 {
+			label = "NAND.file-system";
+			reg = <0x00A00000 0x0F600000>;
 		};
 	};
 };
@@ -643,6 +650,9 @@ &mmc1 {
 	status = "okay";
 	vmmc-supply = <&vmmc_reg>;
 	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
 };
 
 &sham {

arch/arm/boot/dts/am335x-evmsk.dts

@@ -45,6 +45,18 @@ lis3_reg: fixedregulator@1 {
 		regulator-boot-on;
 	};
 
+	wl12xx_vmmc: fixedregulator@2 {
+		pinctrl-names = "default";
+		pinctrl-0 = <&wl12xx_gpio>;
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1271";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio1 29 0>;
+		startup-delay-us = <70000>;
+		enable-active-high;
+	};
+
 	leds {
 		pinctrl-names = "default";
 		pinctrl-0 = <&user_leds_s0>;
@@ -270,6 +282,24 @@ mcasp1_pins: mcasp1_pins {
 			0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */
 		>;
 	};
+
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_31 */
+			0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */
+			0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */
+			0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */
+			0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */
+			0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */
+			0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */
+		>;
+	};
+
+	wl12xx_gpio: pinmux_wl12xx_gpio {
+		pinctrl-single,pins = <
+			0x7c (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_csn0.gpio1_29 */
+		>;
+	};
 };
 
 &uart0 {
@@ -342,9 +372,22 @@ usb-phy@47401300 {
 		status = "okay";
 	};
 
+	usb-phy@47401b00 {
+		status = "okay";
+	};
+
 	usb@47401000 {
 		status = "okay";
 	};
+
+	usb@47401800 {
+		status = "okay";
+		dr_mode = "host";
+	};
+
+	dma-controller@07402000  {
+		status = "okay";
+	};
 };
 
 &epwmss2 {
@@ -440,6 +483,7 @@ &mac {
 	pinctrl-names = "default", "sleep";
 	pinctrl-0 = <&cpsw_default>;
 	pinctrl-1 = <&cpsw_sleep>;
+	dual_emac = <1>;
 };
 
 &davinci_mdio {
@@ -451,11 +495,13 @@ &davinci_mdio {
 &cpsw_emac0 {
 	phy_id = <&davinci_mdio>, <0>;
 	phy-mode = "rgmii-txid";
+	dual_emac_res_vlan = <1>;
 };
 
 &cpsw_emac1 {
 	phy_id = <&davinci_mdio>, <1>;
 	phy-mode = "rgmii-txid";
+	dual_emac_res_vlan = <2>;
 };
 
 &mmc1 {
@@ -479,6 +525,16 @@ &gpio0 {
 	ti,no-reset-on-init;
 };
 
+&mmc2 {
+	status = "okay";
+	vmmc-supply = <&wl12xx_vmmc>;
+	ti,non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+};
+
 &mcasp1 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&mcasp1_pins>;

arch/arm/boot/dts/am33xx.dtsi

@@ -58,6 +58,10 @@ cpu@0 {
 				275000  1125000
 			>;
 			voltage-tolerance = <2>; /* 2 percentage */
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
 			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 	};
@@ -318,6 +322,7 @@ hwspinlock: spinlock@480ca000 {
 			compatible = "ti,omap4-hwspinlock";
 			reg = <0x480ca000 0x1000>;
 			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
 		};
 
 		wdt2: wdt@44e35000 {
@@ -399,7 +404,7 @@ timer7: timer@4804a000 {
 			ti,timer-pwm;
 		};
 
-		rtc@44e3e000 {
+		rtc: rtc@44e3e000 {
 			compatible = "ti,da830-rtc";
 			reg = <0x44e3e000 0x1000>;
 			interrupts = <75
@@ -582,6 +587,8 @@ ecap0: ecap@48300100 {
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48300100 0x80>;
+				interrupts = <31>;
+				interrupt-names = "ecap0";
 				ti,hwmods = "ecap0";
 				status = "disabled";
 			};
@@ -610,6 +617,8 @@ ecap1: ecap@48302100 {
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48302100 0x80>;
+				interrupts = <47>;
+				interrupt-names = "ecap1";
 				ti,hwmods = "ecap1";
 				status = "disabled";
 			};
@@ -638,6 +647,8 @@ ecap2: ecap@48304100 {
 				compatible = "ti,am33xx-ecap";
 				#pwm-cells = <3>;
 				reg = <0x48304100 0x80>;
+				interrupts = <61>;
+				interrupt-names = "ecap2";
 				ti,hwmods = "ecap2";
 				status = "disabled";
 			};

arch/arm/boot/dts/am3517-craneboard.dts

+/*
+ * See craneboard.org for more details
+ *
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+/dts-v1/;
+
+#include "am3517.dtsi"
+
+/ {
+	model = "TI AM3517 CraneBoard (TMDSEVM3517)";
+	compatible = "ti,am3517-craneboard", "ti,am3517", "ti,omap3";
+
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>;	/* 256 MB */
+	};
+
+	vbat: fixedregulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vbat";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+	};
+};
+
+&davinci_emac {
+	status = "okay";
+};
+
+&davinci_mdio {
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <2600000>;
+
+	tps: tps@2d {
+		reg = <0x2d>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+&i2c3 {
+	clock-frequency = <400000>;
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+&mmc1 {
+	vmmc-supply = <&vdd2_reg>;
+	bus-width = <8>;
+};
+
+&mmc2 {
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+&mmc3 {
+	/* goes to expansion connector */
+	status = "disabled";
+};
+
+#include "tps65910.dtsi"
+
+&omap3_pmx_core {
+	tps_pins: pinmux_tps_pins {
+		pinctrl-single,pins = <
+			0x1b0 (PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq.sys_nirq */
+		>;
+	};
+};
+
+&tps {
+	pinctrl-names = "default";
+	pinctrl-0 = <&tps_pins>;
+
+	interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+	interrupt-parent = <&intc>;
+
+	ti,en-ck32k-xtal;
+
+	vcc1-supply = <&vbat>;
+	vcc2-supply = <&vbat>;
+	vcc3-supply = <&vbat>;
+	vcc4-supply = <&vbat>;
+	vcc5-supply = <&vbat>;
+	vcc6-supply = <&vbat>;
+	vcc7-supply = <&vbat>;
+	vccio-supply = <&vbat>;
+
+	regulators {
+		vrtc_reg: regulator@0 {
+			regulator-always-on;
+		};
+
+		vio_reg: regulator@1 {
+			regulator-always-on;
+		};
+
+		/*
+		 * Unused:
+		 * VDIG1=2.7V,300mA max
+		 * VDIG2=1.8V,300mA max
+		 */
+
+		vpll_reg: regulator@7 {
+			/* VDDS_DPLL_1V8 */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		vaux1_reg: regulator@9 {
+			/* VDDS_SRAM_1V8 */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		vaux2_reg: regulator@10 {
+			/* VDDA1P8V_USBPHY */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		/* VAUX33 unused */
+
+		vdac_reg: regulator@8 {
+			/* VDDA_DAC_1V8 */
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		vmmc_reg: regulator@12 {
+			/* VDDA3P3V_USBPHY */
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		vdd1_reg: regulator@2 {
+			/* VDD_CORE */
+			regulator-name = "vdd_core";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-boot-on;
+			regulator-always-on;
+		};
+
+		vdd2_reg: regulator@3 {
+			/* VDDSHV_3V3 */
+			regulator-name = "vdd_shv";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		/* VDD3 unused */
+	};
+};

arch/arm/boot/dts/am4372.dtsi

@@ -8,6 +8,7 @@
  * kind, whether express or implied.
  */
 
+#include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 
 #include "skeleton.dtsi"
@@ -33,6 +34,11 @@ cpu@0 {
 			compatible = "arm,cortex-a9";
 			device_type = "cpu";
 			reg = <0>;
+
+			clocks = <&dpll_mpu_ck>;
+			clock-names = "cpu";
+
+			clock-latency = <300000>; /* From omap-cpufreq driver */
 		};
 	};
 
@@ -351,6 +357,13 @@ gpio5: gpio@48322000 {
 			status = "disabled";
 		};
 
+		hwspinlock: spinlock@480ca000 {
+			compatible = "ti,omap4-hwspinlock";
+			reg = <0x480ca000 0x1000>;
+			ti,hwmods = "spinlock";
+			#hwlock-cells = <1>;
+		};
+
 		i2c0: i2c@44e0b000 {
 			compatible = "ti,am4372-i2c","ti,omap4-i2c";
 			reg = <0x44e0b000 0x1000>;
@@ -521,6 +534,7 @@ epwmss0: epwmss@48300000 {
 
 			ecap0: ecap@48300100 {
 				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				#pwm-cells = <3>;
 				reg = <0x48300100 0x80>;
 				ti,hwmods = "ecap0";
 				status = "disabled";
@@ -528,6 +542,7 @@ ecap0: ecap@48300100 {
 
 			ehrpwm0: ehrpwm@48300200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48300200 0x80>;
 				ti,hwmods = "ehrpwm0";
 				status = "disabled";
@@ -545,6 +560,7 @@ epwmss1: epwmss@48302000 {
 
 			ecap1: ecap@48302100 {
 				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				#pwm-cells = <3>;
 				reg = <0x48302100 0x80>;
 				ti,hwmods = "ecap1";
 				status = "disabled";
@@ -552,6 +568,7 @@ ecap1: ecap@48302100 {
 
 			ehrpwm1: ehrpwm@48302200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48302200 0x80>;
 				ti,hwmods = "ehrpwm1";
 				status = "disabled";
@@ -569,6 +586,7 @@ epwmss2: epwmss@48304000 {
 
 			ecap2: ecap@48304100 {
 				compatible = "ti,am4372-ecap","ti,am33xx-ecap";
+				#pwm-cells = <3>;
 				reg = <0x48304100 0x80>;
 				ti,hwmods = "ecap2";
 				status = "disabled";
@@ -576,6 +594,7 @@ ecap2: ecap@48304100 {
 
 			ehrpwm2: ehrpwm@48304200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48304200 0x80>;
 				ti,hwmods = "ehrpwm2";
 				status = "disabled";
@@ -593,6 +612,7 @@ epwmss3: epwmss@48306000 {
 
 			ehrpwm3: ehrpwm@48306200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48306200 0x80>;
 				ti,hwmods = "ehrpwm3";
 				status = "disabled";
@@ -610,6 +630,7 @@ epwmss4: epwmss@48308000 {
 
 			ehrpwm4: ehrpwm@48308200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x48308200 0x80>;
 				ti,hwmods = "ehrpwm4";
 				status = "disabled";
@@ -627,6 +648,7 @@ epwmss5: epwmss@4830a000 {
 
 			ehrpwm5: ehrpwm@4830a200 {
 				compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm";
+				#pwm-cells = <3>;
 				reg = <0x4830a200 0x80>;
 				ti,hwmods = "ehrpwm5";
 				status = "disabled";
@@ -689,6 +711,30 @@ mcasp1: mcasp@4803C000 {
 			       <&edma 11>;
 			dma-names = "tx", "rx";
 		};
+
+		elm: elm@48080000 {
+			compatible = "ti,am3352-elm";
+			reg = <0x48080000 0x2000>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			ti,hwmods = "elm";
+			clocks = <&l4ls_gclk>;
+			clock-names = "fck";
+			status = "disabled";
+		};
+
+		gpmc: gpmc@50000000 {
+			compatible = "ti,am3352-gpmc";
+			ti,hwmods = "gpmc";
+			clocks = <&l3s_gclk>;
+			clock-names = "fck";
+			reg = <0x50000000 0x2000>;
+			interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
+			gpmc,num-cs = <7>;
+			gpmc,num-waitpins = <2>;
+			#address-cells = <2>;
+			#size-cells = <1>;
+			status = "disabled";
+		};
 	};
 };
 

arch/arm/boot/dts/am437x-gp-evm.dts

+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/* AM437x GP EVM */
+
+/dts-v1/;
+
+#include "am4372.dtsi"
+#include <dt-bindings/pinctrl/am43xx.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "TI AM437x GP EVM";
+	compatible = "ti,am437x-gp-evm","ti,am4372","ti,am43";
+
+	vmmcsd_fixed: fixedregulator-sd {
+		compatible = "regulator-fixed";
+		regulator-name = "vmmcsd_fixed";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
+
+	matrix_keypad: matrix_keypad@0 {
+		compatible = "gpio-matrix-keypad";
+		debounce-delay-ms = <5>;
+		col-scan-delay-us = <2>;
+
+		row-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH /* Bank3, pin21 */
+				&gpio4 3 GPIO_ACTIVE_HIGH /* Bank4, pin3 */
+				&gpio4 2 GPIO_ACTIVE_HIGH>; /* Bank4, pin2 */
+
+		col-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH /* Bank3, pin19 */
+				&gpio3 20 GPIO_ACTIVE_HIGH>; /* Bank3, pin20 */
+
+		linux,keymap = <0x00000201      /* P1 */
+				0x00010202      /* P2 */
+				0x01000067      /* UP */
+				0x0101006a      /* RIGHT */
+				0x02000069      /* LEFT */
+				0x0201006c>;      /* DOWN */
+		};
+};
+
+&am43xx_pinmux {
+	i2c0_pins: i2c0_pins {
+		pinctrl-single,pins = <
+			0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_sda.i2c0_sda */
+			0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)  /* i2c0_scl.i2c0_scl */
+		>;
+	};
+
+	i2c1_pins: i2c1_pins {
+		pinctrl-single,pins = <
+			0x15c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_cs0.i2c1_scl */
+			0x158 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2)  /* spi0_d1.i2c1_sda  */
+		>;
+	};
+
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
+		>;
+	};
+
+	ecap0_pins: backlight_pins {
+		pinctrl-single,pins = <
+			0x164 MUX_MODE0       /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+		>;
+	};
+};
+
+&i2c0 {
+        status = "okay";
+        pinctrl-names = "default";
+        pinctrl-0 = <&i2c0_pins>;
+};
+
+&i2c1 {
+        status = "okay";
+        pinctrl-names = "default";
+        pinctrl-0 = <&i2c1_pins>;
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&ecap0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&ecap0_pins>;
+};
+
+&gpio0 {
+	status = "okay";
+};
+
+&gpio3 {
+	status = "okay";
+};
+
+&gpio4 {
+	status = "okay";
+};
+
+&mmc1 {
+	status = "okay";
+	vmmc-supply = <&vmmcsd_fixed>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+};

arch/arm/boot/dts/am43x-epos-evm.dts

@@ -13,6 +13,7 @@
 #include "am4372.dtsi"
 #include <dt-bindings/pinctrl/am43xx.h>
 #include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
 
 / {
 	model = "TI AM43x EPOS EVM";
@@ -79,6 +80,64 @@ i2c0_pins: pinmux_i2c0_pins {
 				0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0)	/* i2c0_scl.i2c0_scl */
 			>;
 		};
+
+		nand_flash_x8: nand_flash_x8 {
+			pinctrl-single,pins = <
+				0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7)	/* gpmc_a0.SELQSPIorNAND/GPIO */
+				0x0  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad0.gpmc_ad0 */
+				0x4  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad1.gpmc_ad1 */
+				0x8  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad2.gpmc_ad2 */
+				0xc  (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad3.gpmc_ad3 */
+				0x10 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad4.gpmc_ad4 */
+				0x14 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad5.gpmc_ad5 */
+				0x18 (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad6.gpmc_ad6 */
+				0x1c (PIN_INPUT_PULLDOWN | MUX_MODE0)	/* gpmc_ad7.gpmc_ad7 */
+				0x70 (PIN_INPUT_PULLUP | MUX_MODE0)	/* gpmc_wait0.gpmc_wait0 */
+				0x74 (PIN_OUTPUT_PULLUP | MUX_MODE7)	/* gpmc_wpn.gpmc_wpn */
+				0x7c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_csn0.gpmc_csn0  */
+				0x90 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_advn_ale.gpmc_advn_ale */
+				0x94 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_oen_ren.gpmc_oen_ren */
+				0x98 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_wen.gpmc_wen */
+				0x9c (PIN_OUTPUT | MUX_MODE0)		/* gpmc_be0n_cle.gpmc_be0n_cle */
+			>;
+		};
+
+		ecap0_pins: backlight_pins {
+			pinctrl-single,pins = <
+				0x164 MUX_MODE0         /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */
+			>;
+		};
+
+		i2c2_pins: pinmux_i2c2_pins {
+			pinctrl-single,pins = <
+				0x1c0 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8)    /* i2c2_sda.i2c2_sda */
+				0x1c4 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8)    /* i2c2_scl.i2c2_scl */
+			>;
+		};
+
+		spi0_pins: pinmux_spi0_pins {
+			pinctrl-single,pins = <
+				0x150 (PIN_INPUT | MUX_MODE0)           /* spi0_clk.spi0_clk */
+				0x154 (PIN_OUTPUT | MUX_MODE0)           /* spi0_d0.spi0_d0 */
+				0x158 (PIN_INPUT | MUX_MODE0)           /* spi0_d1.spi0_d1 */
+				0x15c (PIN_OUTPUT | MUX_MODE0)          /* spi0_cs0.spi0_cs0 */
+			>;
+		};
+
+		spi1_pins: pinmux_spi1_pins {
+			pinctrl-single,pins = <
+				0x190 (PIN_INPUT | MUX_MODE3)           /* mcasp0_aclkx.spi1_clk */
+				0x194 (PIN_OUTPUT | MUX_MODE3)           /* mcasp0_fsx.spi1_d0 */
+				0x198 (PIN_INPUT | MUX_MODE3)           /* mcasp0_axr0.spi1_d1 */
+				0x19c (PIN_OUTPUT | MUX_MODE3)          /* mcasp0_ahclkr.spi1_cs0 */
+			>;
+		};
+
+		mmc1_pins: pinmux_mmc1_pins {
+			pinctrl-single,pins = <
+				0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */
+			>;
+		};
 	};
 
 	matrix_keypad: matrix_keypad@0 {
@@ -113,12 +172,22 @@ &gpio2 18 GPIO_ACTIVE_HIGH		/* Bank2, pin18 */
 				0x0203006c	/* DOWN */
 				0x03030069>;	/* LEFT */
 		};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>;
+		brightness-levels = <0 51 53 56 62 75 101 152 255>;
+		default-brightness-level = <8>;
+	};
 };
 
 &mmc1 {
 	status = "okay";
 	vmmc-supply = <&vmmcsd_fixed>;
 	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+	cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>;
 };
 
 &mac {
@@ -169,6 +238,12 @@ pixcir_ts@5c {
 	};
 };
 
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+	status = "okay";
+};
+
 &gpio0 {
 	status = "okay";
 };
@@ -184,3 +259,111 @@ &gpio2 {
 &gpio3 {
 	status = "okay";
 };
+
+&elm {
+	status = "okay";
+};
+
+&gpmc {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&nand_flash_x8>;
+	ranges = <0 0 0x08000000 0x10000000>;	/* CS0: NAND */
+	nand@0,0 {
+		reg = <0 0 0>; /* CS0, offset 0 */
+		ti,nand-ecc-opt = "bch8";
+		ti,elm-id = <&elm>;
+		nand-bus-width = <8>;
+		gpmc,device-width = <1>;
+		gpmc,sync-clk-ps = <0>;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <40>; /* tCEA + tCHZ + 1 */
+		gpmc,cs-wr-off-ns = <40>;
+		gpmc,adv-on-ns = <0>;  /* cs-on-ns */
+		gpmc,adv-rd-off-ns = <25>; /* min( tALH + tALS + 1) */
+		gpmc,adv-wr-off-ns = <25>; /* min( tALH + tALS + 1) */
+		gpmc,we-on-ns = <0>;   /* cs-on-ns */
+		gpmc,we-off-ns = <20>; /* we-on-time + tWP + 2 */
+		gpmc,oe-on-ns = <3>;  /* cs-on-ns + tRR + 2 */
+		gpmc,oe-off-ns = <30>; /* oe-on-ns + tRP + 2 */
+		gpmc,access-ns = <30>; /* tCEA + 4*/
+		gpmc,rd-cycle-ns = <40>;
+		gpmc,wr-cycle-ns = <40>;
+		gpmc,wait-on-read = "true";
+		gpmc,wait-on-write = "true";
+		gpmc,bus-turnaround-ns = <0>;
+		gpmc,cycle2cycle-delay-ns = <0>;
+		gpmc,clk-activation-ns = <0>;
+		gpmc,wait-monitoring-ns = <0>;
+		gpmc,wr-access-ns = <40>;
+		gpmc,wr-data-mux-bus-ns = <0>;
+		/* MTD partition table */
+		/* All SPL-* partitions are sized to minimal length
+		 * which can be independently programmable. For
+		 * NAND flash this is equal to size of erase-block */
+		#address-cells = <1>;
+		#size-cells = <1>;
+		partition@0 {
+			label = "NAND.SPL";
+			reg = <0x00000000 0x00040000>;
+		};
+		partition@1 {
+			label = "NAND.SPL.backup1";
+			reg = <0x00040000 0x00040000>;
+		};
+		partition@2 {
+			label = "NAND.SPL.backup2";
+			reg = <0x00080000 0x00040000>;
+		};
+		partition@3 {
+			label = "NAND.SPL.backup3";
+			reg = <0x000C0000 0x00040000>;
+		};
+		partition@4 {
+			label = "NAND.u-boot-spl-os";
+			reg = <0x00100000 0x00080000>;
+		};
+		partition@5 {
+			label = "NAND.u-boot";
+			reg = <0x00180000 0x00100000>;
+		};
+		partition@6 {
+			label = "NAND.u-boot-env";
+			reg = <0x00280000 0x00040000>;
+		};
+		partition@7 {
+			label = "NAND.u-boot-env.backup1";
+			reg = <0x002C0000 0x00040000>;
+		};
+		partition@8 {
+			label = "NAND.kernel";
+			reg = <0x00300000 0x00700000>;
+		};
+		partition@9 {
+			label = "NAND.file-system";
+			reg = <0x00800000 0x1F600000>;
+		};
+	};
+};
+
+&epwmss0 {
+	status = "okay";
+};
+
+&ecap0 {
+		status = "okay";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ecap0_pins>;
+};
+
+&spi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi0_pins>;
+	status = "okay";
+};
+
+&spi1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi1_pins>;
+	status = "okay";
+};

arch/arm/boot/dts/armada-370-db.dts

@@ -64,6 +64,22 @@ ethernet@74000 {
 				phy-mode = "rgmii-id";
 			};
 
+			i2c@11000 {
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				audio_codec: audio-codec@4a {
+					compatible = "cirrus,cs42l51";
+					reg = <0x4a>;
+				};
+			};
+
+			audio-controller@30000 {
+				pinctrl-0 = <&i2s_pins2>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
 			mvsdio@d4000 {
 				pinctrl-0 = <&sdio_pins1>;
 				pinctrl-names = "default";
@@ -80,6 +96,30 @@ mvsdio@d4000 {
 				broken-cd;
 			};
 
+			pinctrl {
+				/*
+				 * These pins might be muxed as I2S by
+				 * the bootloader, but it conflicts
+				 * with the real I2S pins that are
+				 * muxed using i2s_pins. We must mux
+				 * those pins to a function other than
+				 * I2S.
+				 */
+				pinctrl-0 = <&hog_pins1 &hog_pins2>;
+				pinctrl-names = "default";
+
+				hog_pins1: hog-pins1 {
+					marvell,pins = "mpp6",  "mpp8", "mpp10",
+						       "mpp12", "mpp13";
+					marvell,function = "gpio";
+				};
+
+				hog_pins2: hog-pins2 {
+					marvell,pins = "mpp5", "mpp7", "mpp9";
+					marvell,function = "gpo";
+				};
+			};
+
 			usb@50000 {
 				status = "okay";
 			};
@@ -112,10 +152,26 @@ pcie@1,0 {
 				/* Port 0, Lane 0 */
 				status = "okay";
 			};
+
 			pcie@2,0 {
 				/* Port 1, Lane 0 */
 				status = "okay";
 			};
 		};
 	};
+
+	sound {
+	      compatible = "marvell,a370db-audio";
+	      marvell,audio-controller = <&audio_controller>;
+	      marvell,audio-codec = <&audio_codec &spdif_out &spdif_in>;
+	      status = "okay";
+	};
+
+	spdif_out: spdif-out {
+	      compatible = "linux,spdif-dit";
+	};
+
+	spdif_in: spdif-in {
+	      compatible = "linux,spdif-dir";
+	};
 };

arch/arm/boot/dts/armada-370-mirabox.dts

@@ -9,6 +9,7 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
 #include "armada-370.dtsi"
 
 / {
@@ -73,19 +74,19 @@ gpio_leds {
 
 				green_pwr_led {
 					label = "mirabox:green:pwr";
-					gpios = <&gpio1 31 1>;
+					gpios = <&gpio1 31 GPIO_ACTIVE_LOW>;
 					default-state = "keep";
 				};
 
 				blue_stat_led {
 					label = "mirabox:blue:stat";
-					gpios = <&gpio2 0 1>;
+					gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
 					default-state = "off";
 				};
 
 				green_stat_led {
 					label = "mirabox:green:stat";
-					gpios = <&gpio2 1 1>;
+					gpios = <&gpio2 1 GPIO_ACTIVE_LOW>;
 					default-state = "off";
 				};
 			};

arch/arm/boot/dts/armada-370-rd.dts

@@ -12,6 +12,8 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
 #include "armada-370.dtsi"
 
 / {
@@ -100,8 +102,8 @@ gpio-keys {
 				#size-cells = <0>;
 				button@1 {
 					label = "Software Button";
-					linux,code = <116>;
-					gpios = <&gpio0 6 1>;
+					linux,code = <KEY_POWER>;
+					gpios = <&gpio0 6 GPIO_ACTIVE_LOW>;
 				};
 			};
 

arch/arm/boot/dts/armada-370-xp.dtsi

@@ -44,8 +44,8 @@ soc {
 		#size-cells = <1>;
 		controller = <&mbusc>;
 		interrupt-parent = <&mpic>;
-		pcie-mem-aperture = <0xe0000000 0x8000000>;
-		pcie-io-aperture  = <0xe8000000 0x100000>;
+		pcie-mem-aperture = <0xf8000000 0x7e00000>;
+		pcie-io-aperture  = <0xffe00000 0x100000>;
 
 		devbus-bootcs {
 			compatible = "marvell,mvebu-devbus";
@@ -199,6 +199,10 @@ timer@20300 {
 				interrupts = <37>, <38>, <39>, <40>, <5>, <6>;
 			};
 
+			watchdog@20300 {
+				reg = <0x20300 0x34>, <0x20704 0x4>;
+			};
+
 			usb@50000 {
 				compatible = "marvell,orion-ehci";
 				reg = <0x50000 0x500>;

arch/arm/boot/dts/armada-370.dtsi

@@ -132,6 +132,25 @@ sdio_pins3: sdio-pins3 {
 							"mpp51", "mpp52", "mpp53";
 					marvell,function = "sd0";
 				};
+
+				i2c0_pins: i2c0-pins {
+					marvell,pins = "mpp2", "mpp3";
+					marvell,function = "i2c0";
+				};
+
+				i2s_pins1: i2s-pins1 {
+					marvell,pins = "mpp5", "mpp6", "mpp7",
+						       "mpp8", "mpp9", "mpp10",
+						       "mpp12", "mpp13";
+					marvell,function = "audio";
+				};
+
+				i2s_pins2: i2s-pins2 {
+					marvell,pins = "mpp49", "mpp47", "mpp50",
+						       "mpp59", "mpp57", "mpp61",
+						       "mpp62", "mpp60", "mpp58";
+					marvell,function = "audio";
+				};
 			};
 
 			gpio0: gpio@18100 {
@@ -196,6 +215,20 @@ timer@20300 {
 				clocks = <&coreclk 2>;
 			};
 
+			watchdog@20300 {
+				compatible = "marvell,armada-370-wdt";
+				clocks = <&coreclk 2>;
+			};
+
+			audio_controller: audio-controller@30000 {
+				compatible = "marvell,armada370-audio";
+				reg = <0x30000 0x4000>;
+				interrupts = <93>;
+				clocks = <&gateclk 0>;
+				clock-names = "internal";
+				status = "disabled";
+			};
+
 			usb@50000 {
 				clocks = <&coreclk 0>;
 			};

arch/arm/boot/dts/armada-375-db.dts

+/*
+ * Device Tree file for Marvell Armada 375 evaluation board
+ * (DB-88F6720)
+ *
+ *  Copyright (C) 2014 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include "armada-375.dtsi"
+
+/ {
+	model = "Marvell Armada 375 Development Board";
+	compatible = "marvell,a375-db", "marvell,armada375";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x40000000>; /* 1 GB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+		internal-regs {
+			spi@10600 {
+				pinctrl-0 = <&spi0_pins>;
+				pinctrl-names = "default";
+				/*
+				 * SPI conflicts with NAND, so we disable it
+				 * here, and select NAND as the enabled device
+				 * by default.
+				 */
+				status = "disabled";
+
+				spi-flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "n25q128a13";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <108000000>;
+				};
+			};
+
+			i2c@11000 {
+				status = "okay";
+				clock-frequency = <100000>;
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-names = "default";
+			};
+
+			i2c@11100 {
+				status = "okay";
+				clock-frequency = <100000>;
+				pinctrl-0 = <&i2c1_pins>;
+				pinctrl-names = "default";
+			};
+
+			serial@12000 {
+				clock-frequency = <200000000>;
+				status = "okay";
+			};
+
+			pinctrl {
+				sdio_st_pins: sdio-st-pins {
+					marvell,pins = "mpp44", "mpp45";
+					marvell,function = "gpio";
+				};
+			};
+
+			nand: nand@d0000 {
+				pinctrl-0 = <&nand_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+
+				partition@0 {
+					label = "U-Boot";
+					reg = <0 0x800000>;
+				};
+				partition@800000 {
+					label = "Linux";
+					reg = <0x800000 0x800000>;
+				};
+				partition@1000000 {
+					label = "Filesystem";
+					reg = <0x1000000 0x3f000000>;
+				};
+			};
+
+			mvsdio@d4000 {
+				pinctrl-0 = <&sdio_pins &sdio_st_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				cd-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+				wp-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+			/*
+			 * The two PCIe units are accessible through
+			 * standard PCIe slots on the board.
+			 */
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+			pcie@2,0 {
+				/* Port 1, Lane 0 */
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/armada-380.dtsi

+/*
+ * Device Tree Include file for Marvell Armada 380 SoC.
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include "armada-38x.dtsi"
+
+/ {
+	model = "Marvell Armada 380 family SoC";
+	compatible = "marvell,armada380", "marvell,armada38x";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+		};
+	};
+
+	soc {
+		internal-regs {
+			pinctrl {
+				compatible = "marvell,mv88f6810-pinctrl";
+				reg = <0x18000 0x20>;
+			};
+		};
+
+		pcie-controller {
+			compatible = "marvell,armada-370-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			msi-parent = <&mpic>;
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
+				0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
+				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000
+				0x82000000 0x1 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */
+				0x81000000 0x1 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO  */
+				0x82000000 0x2 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */
+				0x81000000 0x2 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO  */
+				0x82000000 0x3 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */
+				0x81000000 0x3 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO  */>;
+
+			/* x1 port */
+			pcie@1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 8>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie@2,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie@3,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
+					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <2>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 6>;
+				status = "disabled";
+			};
+		};
+	};
+};

arch/arm/boot/dts/armada-385-db.dts

+/*
+ * Device Tree file for Marvell Armada 385 evaluation board
+ * (DB-88F6820)
+ *
+ *  Copyright (C) 2014 Marvell
+ *
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include "armada-385.dtsi"
+
+/ {
+	model = "Marvell Armada 385 Development Board";
+	compatible = "marvell,a385-db", "marvell,armada385", "marvell,armada38x";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>; /* 256 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+		internal-regs {
+			spi@10600 {
+				status = "okay";
+
+				spi-flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "w25q32";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <108000000>;
+				};
+			};
+
+			i2c@11000 {
+				status = "okay";
+				clock-frequency = <100000>;
+			};
+
+			i2c@11100 {
+				status = "okay";
+				clock-frequency = <100000>;
+			};
+
+			serial@12000 {
+				clock-frequency = <200000000>;
+				status = "okay";
+			};
+
+			ethernet@30000 {
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "rgmii-id";
+			};
+
+			ethernet@70000 {
+				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "rgmii-id";
+			};
+
+			mdio {
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+
+			flash@d0000 {
+				status = "okay";
+				num-cs = <1>;
+				marvell,nand-keep-config;
+				marvell,nand-enable-arbiter;
+				nand-on-flash-bbt;
+
+				partition@0 {
+					label = "U-Boot";
+					reg = <0 0x800000>;
+				};
+				partition@800000 {
+					label = "Linux";
+					reg = <0x800000 0x800000>;
+				};
+				partition@1000000 {
+					label = "Filesystem";
+					reg = <0x1000000 0x3f000000>;
+				};
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+			/*
+			 * The two PCIe units are accessible through
+			 * standard PCIe slots on the board.
+			 */
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+			pcie@2,0 {
+				/* Port 1, Lane 0 */
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/armada-385-rd.dts

+/*
+ * Device Tree file for Marvell Armada 385 Reference Design board
+ * (RD-88F6820-AP)
+ *
+ *  Copyright (C) 2014 Marvell
+ *
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include "armada-385.dtsi"
+
+/ {
+	model = "Marvell Armada 385 Reference Design";
+	compatible = "marvell,a385-rd", "marvell,armada385", "marvell,armada38x";
+
+	chosen {
+		bootargs = "console=ttyS0,115200 earlyprintk";
+	};
+
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>; /* 256 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>;
+
+		internal-regs {
+			spi@10600 {
+				status = "okay";
+
+				spi-flash@0 {
+					#address-cells = <1>;
+					#size-cells = <1>;
+					compatible = "st,m25p128";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <108000000>;
+				};
+			};
+
+			i2c@11000 {
+				status = "okay";
+				clock-frequency = <100000>;
+			};
+
+			serial@12000 {
+				clock-frequency = <200000000>;
+				status = "okay";
+			};
+
+			ethernet@30000 {
+				status = "okay";
+				phy = <&phy0>;
+				phy-mode = "rgmii-id";
+			};
+
+			ethernet@70000 {
+				status = "okay";
+				phy = <&phy1>;
+				phy-mode = "rgmii-id";
+			};
+
+
+			mdio {
+				phy0: ethernet-phy@0 {
+					reg = <0>;
+				};
+
+				phy1: ethernet-phy@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+			/*
+			 * One PCIe units is accessible through
+			 * standard PCIe slot on the board.
+			 */
+			pcie@1,0 {
+				/* Port 0, Lane 0 */
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/armada-385.dtsi

+/*
+ * Device Tree Include file for Marvell Armada 385 SoC.
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include "armada-38x.dtsi"
+
+/ {
+	model = "Marvell Armada 385 family SoC";
+	compatible = "marvell,armada385", "marvell,armada38x";
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		cpu@0 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <0>;
+		};
+		cpu@1 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a9";
+			reg = <1>;
+		};
+	};
+
+	soc {
+		internal-regs {
+			pinctrl {
+				compatible = "marvell,mv88f6820-pinctrl";
+				reg = <0x18000 0x20>;
+			};
+		};
+
+		pcie-controller {
+			compatible = "marvell,armada-370-pcie";
+			status = "disabled";
+			device_type = "pci";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			msi-parent = <&mpic>;
+			bus-range = <0x00 0xff>;
+
+			ranges =
+			       <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000
+				0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000
+				0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000
+				0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000
+				0x82000000 0x1 0     MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */
+				0x81000000 0x1 0     MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO  */
+				0x82000000 0x2 0     MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */
+				0x81000000 0x2 0     MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO  */
+				0x82000000 0x3 0     MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */
+				0x81000000 0x3 0     MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO  */
+				0x82000000 0x4 0     MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 3 MEM */
+				0x81000000 0x4 0     MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 3 IO  */>;
+
+			/*
+			 * This port can be either x4 or x1. When
+			 * configured in x4 by the bootloader, then
+			 * pcie@4,0 is not available.
+			 */
+			pcie@1,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x80000 0 0x2000>;
+				reg = <0x0800 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+					  0x81000000 0 0 0x81000000 0x1 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <0>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 8>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie@2,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0
+					  0x81000000 0 0 0x81000000 0x2 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <1>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 5>;
+				status = "disabled";
+			};
+
+			/* x1 port */
+			pcie@3,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x44000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0
+					  0x81000000 0 0 0x81000000 0x3 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <2>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 6>;
+				status = "disabled";
+			};
+
+			/*
+			 * x1 port only available when pcie@1,0 is
+			 * configured as a x1 port
+			 */
+			pcie@4,0 {
+				device_type = "pci";
+				assigned-addresses = <0x82000800 0 0x48000 0 0x2000>;
+				reg = <0x1000 0 0 0 0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				#interrupt-cells = <1>;
+				ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0
+					  0x81000000 0 0 0x81000000 0x4 0 1 0>;
+				interrupt-map-mask = <0 0 0 0>;
+				interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+				marvell,pcie-port = <3>;
+				marvell,pcie-lane = <0>;
+				clocks = <&gateclk 7>;
+				status = "disabled";
+			};
+		};
+	};
+};

arch/arm/boot/dts/armada-38x.dtsi

+/*
+ * Device Tree Include file for Marvell Armada 38x family of SoCs.
+ *
+ * Copyright (C) 2014 Marvell
+ *
+ * Lior Amsalem <alior@marvell.com>
+ * Gregory CLEMENT <gregory.clement@free-electrons.com>
+ * Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2.  This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include "skeleton.dtsi"
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16))
+
+/ {
+	model = "Marvell Armada 38x family SoC";
+	compatible = "marvell,armada38x";
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		eth0 = &eth0;
+		eth1 = &eth1;
+		eth2 = &eth2;
+	};
+
+	soc {
+		compatible = "marvell,armada380-mbus", "marvell,armada370-mbus",
+			     "simple-bus";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		controller = <&mbusc>;
+		interrupt-parent = <&gic>;
+		pcie-mem-aperture = <0xe0000000 0x8000000>;
+		pcie-io-aperture  = <0xe8000000 0x100000>;
+
+		bootrom {
+			compatible = "marvell,bootrom";
+			reg = <MBUS_ID(0x01, 0x1d) 0 0x200000>;
+		};
+
+		devbus-bootcs {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10400 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x2f) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs0 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10408 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3e) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs1 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10410 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3d) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs2 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10418 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x3b) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		devbus-cs3 {
+			compatible = "marvell,mvebu-devbus";
+			reg = <MBUS_ID(0xf0, 0x01) 0x10420 0x8>;
+			ranges = <0 MBUS_ID(0x01, 0x37) 0 0xffffffff>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			clocks = <&coreclk 0>;
+			status = "disabled";
+		};
+
+		internal-regs {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>;
+
+			L2: cache-controller@8000 {
+				compatible = "arm,pl310-cache";
+				reg = <0x8000 0x1000>;
+				cache-unified;
+				cache-level = <2>;
+			};
+
+			timer@c600 {
+				compatible = "arm,cortex-a9-twd-timer";
+				reg = <0xc600 0x20>;
+				interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>;
+				clocks = <&coreclk 2>;
+			};
+
+			gic: interrupt-controller@d000 {
+				compatible = "arm,cortex-a9-gic";
+				#interrupt-cells = <3>;
+				#size-cells = <0>;
+				interrupt-controller;
+				reg = <0xd000 0x1000>,
+				      <0xc100 0x100>;
+			};
+
+			spi0: spi@10600 {
+				compatible = "marvell,orion-spi";
+				reg = <0x10600 0x50>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				cell-index = <0>;
+				interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			spi1: spi@10680 {
+				compatible = "marvell,orion-spi";
+				reg = <0x10680 0x50>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				cell-index = <1>;
+				interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@11000 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11000 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@11100 {
+				compatible = "marvell,mv64xxx-i2c";
+				reg = <0x11100 0x20>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+				timeout-ms = <1000>;
+				clocks = <&coreclk 0>;
+				status = "disabled";
+			};
+
+			serial@12000 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12000 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				status = "disabled";
+			};
+
+			serial@12100 {
+				compatible = "snps,dw-apb-uart";
+				reg = <0x12100 0x100>;
+				reg-shift = <2>;
+				interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+				reg-io-width = <1>;
+				status = "disabled";
+			};
+
+			pinctrl {
+				compatible = "marvell,mv88f6820-pinctrl";
+				reg = <0x18000 0x20>;
+			};
+
+			gpio0: gpio@18100 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18100 0x40>;
+				ngpios = <32>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			gpio1: gpio@18140 {
+				compatible = "marvell,orion-gpio";
+				reg = <0x18140 0x40>;
+				ngpios = <28>;
+				gpio-controller;
+				#gpio-cells = <2>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			system-controller@18200 {
+				compatible = "marvell,armada-380-system-controller",
+					     "marvell,armada-370-xp-system-controller";
+				reg = <0x18200 0x100>;
+			};
+
+			gateclk: clock-gating-control@18220 {
+				compatible = "marvell,armada-380-gating-clock";
+				reg = <0x18220 0x4>;
+				clocks = <&coreclk 0>;
+				#clock-cells = <1>;
+			};
+
+			coreclk: mvebu-sar@18600 {
+				compatible = "marvell,armada-380-core-clock";
+				reg = <0x18600 0x04>;
+				#clock-cells = <1>;
+			};
+
+			mbusc: mbus-controller@20000 {
+				compatible = "marvell,mbus-controller";
+				reg = <0x20000 0x100>, <0x20180 0x20>;
+			};
+
+			mpic: interrupt-controller@20000 {
+				compatible = "marvell,mpic";
+				reg = <0x20a00 0x2d0>, <0x21070 0x58>;
+				#interrupt-cells = <1>;
+				#size-cells = <1>;
+				interrupt-controller;
+				msi-controller;
+				interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
+			timer@20300 {
+				compatible = "marvell,armada-380-timer",
+					     "marvell,armada-xp-timer";
+				reg = <0x20300 0x30>, <0x21040 0x30>;
+				interrupts-extended = <&gic  GIC_SPI  8 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+						      <&gic  GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+						      <&mpic 5>,
+						      <&mpic 6>;
+				clocks = <&coreclk 2>, <&refclk>;
+				clock-names = "nbclk", "fixed";
+			};
+
+			eth1: ethernet@30000 {
+				compatible = "marvell,armada-370-neta";
+				reg = <0x30000 0x4000>;
+				interrupts-extended = <&mpic 10>;
+				clocks = <&gateclk 3>;
+				status = "disabled";
+			};
+
+			eth2: ethernet@34000 {
+				compatible = "marvell,armada-370-neta";
+				reg = <0x34000 0x4000>;
+				interrupts-extended = <&mpic 12>;
+				clocks = <&gateclk 2>;
+				status = "disabled";
+			};
+
+			xor@60800 {
+				compatible = "marvell,orion-xor";
+				reg = <0x60800 0x100
+				       0x60a00 0x100>;
+				clocks = <&gateclk 22>;
+				status = "okay";
+
+				xor00 {
+					interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+				};
+				xor01 {
+					interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+					dmacap,memset;
+				};
+			};
+
+			xor@60900 {
+				compatible = "marvell,orion-xor";
+				reg = <0x60900 0x100
+				       0x60b00 0x100>;
+				clocks = <&gateclk 28>;
+				status = "okay";
+
+				xor10 {
+					interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+				};
+				xor11 {
+					interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+					dmacap,memcpy;
+					dmacap,xor;
+					dmacap,memset;
+				};
+			};
+
+			eth0: ethernet@70000 {
+				compatible = "marvell,armada-370-neta";
+				reg = <0x70000 0x4000>;
+				interrupts-extended = <&mpic 8>;
+				clocks = <&gateclk 4>;
+				status = "disabled";
+			};
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "marvell,orion-mdio";
+				reg = <0x72004 0x4>;
+			};
+
+			coredivclk: clock@e4250 {
+				compatible = "marvell,armada-380-corediv-clock";
+				reg = <0xe4250 0xc>;
+				#clock-cells = <1>;
+				clocks = <&mainpll>;
+				clock-output-names = "nand";
+			};
+
+			flash@d0000 {
+				compatible = "marvell,armada370-nand";
+				reg = <0xd0000 0x54>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&coredivclk 0>;
+				status = "disabled";
+			};
+		};
+	};
+
+	clocks {
+		/* 2 GHz fixed main PLL */
+		mainpll: mainpll {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <2000000000>;
+		};
+
+		/* 25 MHz reference crystal */
+		refclk: oscillator {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <25000000>;
+		};
+	};
+};

arch/arm/boot/dts/armada-xp-axpwifiap.dts

@@ -16,6 +16,8 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 #include "armada-xp-mv78230.dtsi"
 
 / {
@@ -157,8 +159,8 @@ gpio_keys {
 
 		button@1 {
 			label = "Factory Reset Button";
-			linux,code = <141>; /* KEY_SETUP */
-			gpios = <&gpio1 1 1>;
+			linux,code = <KEY_SETUP>;
+			gpios = <&gpio1 1 GPIO_ACTIVE_LOW>;
 		};
 	};
 };

arch/arm/boot/dts/armada-xp-db.dts

@@ -2,7 +2,7 @@
  * Device Tree file for Marvell Armada XP evaluation board
  * (DB-78460-BP)
  *
- * Copyright (C) 2012 Marvell
+ * Copyright (C) 2012-2014 Marvell
  *
  * Lior Amsalem <alior@marvell.com>
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
@@ -11,6 +11,15 @@
  * This file is licensed under the terms of the GNU General Public
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
+  *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
  */
 
 /dts-v1/;
@@ -30,7 +39,7 @@ memory {
 	};
 
 	soc {
-		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
 			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
 			  MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000>;
 

arch/arm/boot/dts/armada-xp-gp.dts

@@ -2,7 +2,7 @@
  * Device Tree file for Marvell Armada XP development board
  * (DB-MV784MP-GP)
  *
- * Copyright (C) 2013 Marvell
+ * Copyright (C) 2013-2014 Marvell
  *
  * Lior Amsalem <alior@marvell.com>
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
@@ -11,6 +11,15 @@
  * This file is licensed under the terms of the GNU General Public
  * License version 2.  This program is licensed "as is" without any
  * warranty of any kind, whether express or implied.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
  */
 
 /dts-v1/;
@@ -30,16 +39,17 @@ memory {
                  * 8 GB of plug-in RAM modules by default.The amount
                  * of memory available can be changed by the
                  * bootloader according the size of the module
-                 * actually plugged. Only 7GB are usable because
-                 * addresses from 0xC0000000 to 0xffffffff are used by
-                 * the internal registers of the SoC.
+                 * actually plugged. However, memory between
+                 * 0xF0000000 to 0xFFFFFFFF cannot be used, as it is
+                 * the address range used for I/O (internal registers,
+                 * MBus windows).
 		 */
-		reg = <0x00000000 0x00000000 0x00000000 0xC0000000>,
+		reg = <0x00000000 0x00000000 0x00000000 0xf0000000>,
 		      <0x00000001 0x00000000 0x00000001 0x00000000>;
 	};
 
 	soc {
-		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
 			  MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
 			  MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000>;
 

arch/arm/boot/dts/armada-xp-matrix.dts

@@ -23,7 +23,12 @@ chosen {
 
 	memory {
 		device_type = "memory";
-		reg = <0 0x00000000 0 0x80000000>; /* 2 GB */
+		/*
+		 * This board has 4 GB of RAM, but the last 256 MB of
+		 * RAM are not usable due to the overlap with the MBus
+		 * Window address range
+		 */
+		reg = <0 0x00000000 0 0xf0000000>;
 	};
 
 	soc {

arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts

@@ -11,6 +11,8 @@
  */
 
 /dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
 #include "armada-xp-mv78260.dtsi"
 
 / {
@@ -90,19 +92,19 @@ leds {
 
 				red_led {
 					label = "red_led";
-					gpios = <&gpio1 17 1>;
+					gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
 					default-state = "off";
 				};
 
 				yellow_led {
 					label = "yellow_led";
-					gpios = <&gpio1 19 1>;
+					gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
 					default-state = "off";
 				};
 
 				green_led {
 					label = "green_led";
-					gpios = <&gpio1 21 1>;
+					gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
 					default-state = "keep";
 				};
 			};
@@ -114,8 +116,8 @@ gpio_keys {
 
 				button@1 {
 					label = "Init Button";
-					linux,code = <116>;
-					gpios = <&gpio1 28 0>;
+					linux,code = <KEY_POWER>;
+					gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
 				};
 			};
 

arch/arm/boot/dts/armada-xp.dtsi

@@ -111,6 +111,12 @@ timer@20300 {
 				clock-names = "nbclk", "fixed";
 			};
 
+			watchdog@20300 {
+				compatible = "marvell,armada-xp-wdt";
+				clocks = <&coreclk 2>, <&refclk>;
+				clock-names = "nbclk", "fixed";
+			};
+
 			armada-370-xp-pmsu@22000 {
 				compatible = "marvell,armada-370-xp-pmsu";
 				reg = <0x22100 0x400>, <0x20800 0x20>;

arch/arm/boot/dts/at91-ariag25.dts

@@ -129,7 +129,6 @@ uart1: serial@f8044000 {
 			adc0: adc@f804c000 {
 				status = "okay";
 				atmel,adc-channels-used = <0xf>;
-				atmel,adc-num-channels = <4>;
 			};
 
 			dbgu: serial@fffff200 {

arch/arm/boot/dts/at91-cosino.dtsi

@@ -64,7 +64,6 @@ i2c0: i2c@f8010000 {
 			};
 
 			adc0: adc@f804c000 {
-				atmel,adc-clock-rate = <1000000>;
 				atmel,adc-ts-wires = <4>;
 				atmel,adc-ts-pressure-threshold = <10000>;
 				status = "okay";

arch/arm/boot/dts/at91-cosino_mega2560.dts

@@ -27,7 +27,6 @@ macb0: ethernet@f802c000 {
 			};
 
 			adc0: adc@f804c000 {
-				atmel,adc-clock-rate = <1000000>;
 				atmel,adc-ts-wires = <4>;
 				atmel,adc-ts-pressure-threshold = <10000>;
 				status = "okay";

arch/arm/boot/dts/at91sam9260.dtsi

@@ -608,37 +608,38 @@ spi1: spi@fffcc000 {
 			};
 
 			adc0: adc@fffe0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				compatible = "atmel,at91sam9260-adc";
 				reg = <0xfffe0000 0x100>;
 				interrupts = <5 IRQ_TYPE_LEVEL_HIGH 0>;
 				atmel,adc-use-external-triggers;
 				atmel,adc-channels-used = <0xf>;
 				atmel,adc-vref = <3300>;
-				atmel,adc-num-channels = <4>;
 				atmel,adc-startup-time = <15>;
-				atmel,adc-channel-base = <0x30>;
-				atmel,adc-drdy-mask = <0x10000>;
-				atmel,adc-status-register = <0x1c>;
-				atmel,adc-trigger-register = <0x04>;
 				atmel,adc-res = <8 10>;
 				atmel,adc-res-names = "lowres", "highres";
 				atmel,adc-use-res = "highres";
 
 				trigger@0 {
+					reg = <0>;
 					trigger-name = "timer-counter-0";
 					trigger-value = <0x1>;
 				};
 				trigger@1 {
+					reg = <1>;
 					trigger-name = "timer-counter-1";
 					trigger-value = <0x3>;
 				};
 
 				trigger@2 {
+					reg = <2>;
 					trigger-name = "timer-counter-2";
 					trigger-value = <0x5>;
 				};
 
 				trigger@3 {
+					reg = <3>;
 					trigger-name = "external";
 					trigger-value = <0x13>;
 					trigger-external;

arch/arm/boot/dts/at91sam9g45.dtsi

@@ -632,40 +632,41 @@ ssc1: ssc@fffa0000 {
 			};
 
 			adc0: adc@fffb0000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				compatible = "atmel,at91sam9260-adc";
 				reg = <0xfffb0000 0x100>;
 				interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
 				atmel,adc-use-external-triggers;
 				atmel,adc-channels-used = <0xff>;
 				atmel,adc-vref = <3300>;
-				atmel,adc-num-channels = <8>;
 				atmel,adc-startup-time = <40>;
-				atmel,adc-channel-base = <0x30>;
-				atmel,adc-drdy-mask = <0x10000>;
-				atmel,adc-status-register = <0x1c>;
-				atmel,adc-trigger-register = <0x08>;
 				atmel,adc-res = <8 10>;
 				atmel,adc-res-names = "lowres", "highres";
 				atmel,adc-use-res = "highres";
 
 				trigger@0 {
+					reg = <0>;
 					trigger-name = "external-rising";
 					trigger-value = <0x1>;
 					trigger-external;
 				};
 				trigger@1 {
+					reg = <1>;
 					trigger-name = "external-falling";
 					trigger-value = <0x2>;
 					trigger-external;
 				};
 
 				trigger@2 {
+					reg = <2>;
 					trigger-name = "external-any";
 					trigger-value = <0x3>;
 					trigger-external;
 				};
 
 				trigger@3 {
+					reg = <3>;
 					trigger-name = "continuous";
 					trigger-value = <0x6>;
 				};
@@ -817,6 +818,7 @@ nand0: nand@40000000 {
 			      >;
 			atmel,nand-addr-offset = <21>;
 			atmel,nand-cmd-offset = <22>;
+			atmel,nand-has-dma;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			gpios = <&pioC 8 GPIO_ACTIVE_HIGH

arch/arm/boot/dts/at91sam9n12.dtsi

@@ -570,6 +570,7 @@ nand0: nand@40000000 {
 			atmel,pmecc-lookup-table-offset = <0x0 0x8000>;
 			atmel,nand-addr-offset = <21>;
 			atmel,nand-cmd-offset = <22>;
+			atmel,nand-has-dma;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			gpios = <&pioD 5 GPIO_ACTIVE_HIGH

arch/arm/boot/dts/at91sam9x5.dtsi

@@ -621,41 +621,42 @@ uart1: serial@f8044000 {
 			};
 
 			adc0: adc@f804c000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
 				compatible = "atmel,at91sam9260-adc";
 				reg = <0xf804c000 0x100>;
 				interrupts = <19 IRQ_TYPE_LEVEL_HIGH 0>;
-				atmel,adc-use-external;
+				atmel,adc-use-external-triggers;
 				atmel,adc-channels-used = <0xffff>;
 				atmel,adc-vref = <3300>;
-				atmel,adc-num-channels = <12>;
 				atmel,adc-startup-time = <40>;
-				atmel,adc-channel-base = <0x50>;
-				atmel,adc-drdy-mask = <0x1000000>;
-				atmel,adc-status-register = <0x30>;
-				atmel,adc-trigger-register = <0xc0>;
 				atmel,adc-res = <8 10>;
 				atmel,adc-res-names = "lowres", "highres";
 				atmel,adc-use-res = "highres";
 
 				trigger@0 {
+					reg = <0>;
 					trigger-name = "external-rising";
 					trigger-value = <0x1>;
 					trigger-external;
 				};
 
 				trigger@1 {
+					reg = <1>;
 					trigger-name = "external-falling";
 					trigger-value = <0x2>;
 					trigger-external;
 				};
 
 				trigger@2 {
+					reg = <2>;
 					trigger-name = "external-any";
 					trigger-value = <0x3>;
 					trigger-external;
 				};
 
 				trigger@3 {
+					reg = <3>;
 					trigger-name = "continuous";
 					trigger-value = <0x6>;
 				};
@@ -790,6 +791,7 @@ nand0: nand@40000000 {
 			atmel,pmecc-lookup-table-offset = <0x0 0x8000>;
 			atmel,nand-addr-offset = <21>;
 			atmel,nand-cmd-offset = <22>;
+			atmel,nand-has-dma;
 			pinctrl-names = "default";
 			pinctrl-0 = <&pinctrl_nand>;
 			gpios = <&pioD 5 GPIO_ACTIVE_HIGH

arch/arm/boot/dts/bcm11351.dtsi

@@ -14,6 +14,8 @@
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 
+#include "dt-bindings/clock/bcm281xx.h"
+
 #include "skeleton.dtsi"
 
 / {
@@ -43,7 +45,7 @@ uart@3e000000 {
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
 		status = "disabled";
 		reg = <0x3e000000 0x1000>;
-		clocks = <&uartb_clk>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB>;
 		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
@@ -53,7 +55,7 @@ uart@3e001000 {
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
 		status = "disabled";
 		reg = <0x3e001000 0x1000>;
-		clocks = <&uartb2_clk>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB2>;
 		interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
@@ -63,7 +65,7 @@ uart@3e002000 {
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
 		status = "disabled";
 		reg = <0x3e002000 0x1000>;
-		clocks = <&uartb3_clk>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB3>;
 		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
@@ -73,7 +75,7 @@ uart@3e003000 {
 		compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart";
 		status = "disabled";
 		reg = <0x3e003000 0x1000>;
-		clocks = <&uartb4_clk>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB4>;
 		interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
@@ -95,7 +97,7 @@ timer@35006000 {
 		compatible = "brcm,kona-timer";
 		reg = <0x35006000 0x1000>;
 		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&hub_timer_clk>;
+		clocks = <&aon_ccu BCM281XX_AON_CCU_HUB_TIMER>;
 	};
 
 	gpio: gpio@35003000 {
@@ -118,7 +120,7 @@ sdio1: sdio@3f180000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f180000 0x10000>;
 		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&sdio1_clk>;
+		clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO1>;
 		status = "disabled";
 	};
 
@@ -126,7 +128,7 @@ sdio2: sdio@3f190000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f190000 0x10000>;
 		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&sdio2_clk>;
+		clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO2>;
 		status = "disabled";
 	};
 
@@ -134,7 +136,7 @@ sdio3: sdio@3f1a0000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f1a0000 0x10000>;
 		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&sdio3_clk>;
+		clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO3>;
 		status = "disabled";
 	};
 
@@ -142,7 +144,7 @@ sdio4: sdio@3f1b0000 {
 		compatible = "brcm,kona-sdhci";
 		reg = <0x3f1b0000 0x10000>;
 		interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&sdio4_clk>;
+		clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO4>;
 		status = "disabled";
 	};
 
@@ -157,7 +159,7 @@ i2c@3e016000 {
 		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&bsc1_clk>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_BSC1>;
 		status = "disabled";
 	};
 
@@ -167,7 +169,7 @@ i2c@3e017000 {
 		interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&bsc2_clk>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_BSC2>;
 		status = "disabled";
 	};
 
@@ -177,7 +179,7 @@ i2c@3e018000 {
 		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&bsc3_clk>;
+		clocks = <&slave_ccu BCM281XX_SLAVE_CCU_BSC3>;
 		status = "disabled";
 	};
 
@@ -187,105 +189,191 @@ i2c@3500d000 {
 		interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		clocks = <&pmu_bsc_clk>;
+		clocks = <&aon_ccu BCM281XX_AON_CCU_PMU_BSC>;
 		status = "disabled";
 	};
 
 	clocks {
-		bsc1_clk: bsc1 {
-			compatible = "fixed-clock";
-			clock-frequency = <13000000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		root_ccu: root_ccu {
+			compatible = "brcm,bcm11351-root-ccu";
+			reg = <0x35001000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "frac_1m";
+		};
+
+		hub_ccu: hub_ccu {
+			compatible = "brcm,bcm11351-hub-ccu";
+			reg = <0x34000000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "tmon_1m";
+		};
+
+		aon_ccu: aon_ccu {
+			compatible = "brcm,bcm11351-aon-ccu";
+			reg = <0x35002000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "hub_timer",
+					     "pmu_bsc",
+					     "pmu_bsc_var";
+		};
+
+		master_ccu: master_ccu {
+			compatible = "brcm,bcm11351-master-ccu";
+			reg = <0x3f001000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "sdio1",
+					     "sdio2",
+					     "sdio3",
+					     "sdio4",
+					     "usb_ic",
+					     "hsic2_48m",
+					     "hsic2_12m";
+		};
+
+		slave_ccu: slave_ccu {
+			compatible = "brcm,bcm11351-slave-ccu";
+			reg = <0x3e011000 0x0f00>;
+			#clock-cells = <1>;
+			clock-output-names = "uartb",
+					     "uartb2",
+					     "uartb3",
+					     "uartb4",
+					     "ssp0",
+					     "ssp2",
+					     "bsc1",
+					     "bsc2",
+					     "bsc3",
+					     "pwm";
+		};
+
+		ref_1m_clk: ref_1m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <1000000>;
 		};
 
-		bsc2_clk: bsc2 {
+		ref_32k_clk: ref_32k {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
-			clock-frequency = <13000000>;
+			clock-frequency = <32768>;
+		};
+
+		bbl_32k_clk: bbl_32k {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
 		};
 
-		bsc3_clk: bsc3 {
+		ref_13m_clk: ref_13m {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <13000000>;
-			#clock-cells = <0>;
 		};
 
-		pmu_bsc_clk: pmu_bsc {
+		var_13m_clk: var_13m {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <13000000>;
-			#clock-cells = <0>;
 		};
 
-		hub_timer_clk: hub_timer {
-			compatible = "fixed-clock";
-			clock-frequency = <32768>;
+		dft_19_5m_clk: dft_19_5m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <19500000>;
 		};
 
-		pwm_clk: pwm {
+		ref_crystal_clk: ref_crystal {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
 			clock-frequency = <26000000>;
-			#clock-cells = <0>;
 		};
 
-		sdio1_clk: sdio1 {
-			compatible = "fixed-clock";
-			clock-frequency = <48000000>;
+		ref_cx40_clk: ref_cx40 {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <40000000>;
 		};
 
-		sdio2_clk: sdio2 {
-			compatible = "fixed-clock";
-			clock-frequency = <48000000>;
+		ref_52m_clk: ref_52m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <52000000>;
 		};
 
-		sdio3_clk: sdio3 {
-			compatible = "fixed-clock";
-			clock-frequency = <48000000>;
+		var_52m_clk: var_52m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <52000000>;
 		};
 
-		sdio4_clk: sdio4 {
+		usb_otg_ahb_clk: usb_otg_ahb {
 			compatible = "fixed-clock";
-			clock-frequency = <48000000>;
+			clock-frequency = <52000000>;
 			#clock-cells = <0>;
 		};
 
-		tmon_1m_clk: tmon_1m {
-			compatible = "fixed-clock";
-			clock-frequency = <1000000>;
+		ref_96m_clk: ref_96m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <96000000>;
 		};
 
-		uartb_clk: uartb {
-			compatible = "fixed-clock";
-			clock-frequency = <13000000>;
+		var_96m_clk: var_96m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <96000000>;
 		};
 
-		uartb2_clk: uartb2 {
+		ref_104m_clk: ref_104m {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
-			clock-frequency = <13000000>;
+			clock-frequency = <104000000>;
+		};
+
+		var_104m_clk: var_104m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <104000000>;
 		};
 
-		uartb3_clk: uartb3 {
+		ref_156m_clk: ref_156m {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
-			clock-frequency = <13000000>;
+			clock-frequency = <156000000>;
+		};
+
+		var_156m_clk: var_156m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <156000000>;
 		};
 
-		uartb4_clk: uartb4 {
+		ref_208m_clk: ref_208m {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
-			clock-frequency = <13000000>;
+			clock-frequency = <208000000>;
+		};
+
+		var_208m_clk: var_208m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <208000000>;
 		};
 
-		usb_otg_ahb_clk: usb_otg_ahb {
+		ref_312m_clk: ref_312m {
+			#clock-cells = <0>;
 			compatible = "fixed-clock";
-			clock-frequency = <52000000>;
+			clock-frequency = <312000000>;
+		};
+
+		var_312m_clk: var_312m {
 			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <312000000>;
 		};
 	};
 

arch/arm/boot/dts/bcm11351-brt.dts → arch/arm/boot/dts/bcm21664-garnet.dts

 /*
- * Copyright (C) 2012 Broadcom Corporation
+ * Copyright (C) 2014 Broadcom Corporation
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
@@ -13,11 +13,13 @@
 
 /dts-v1/;
 
-#include "bcm11351.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+#include "bcm21664.dtsi"
 
 / {
-	model = "BCM11351 BRT board";
-	compatible = "brcm,bcm11351-brt", "brcm,bcm11351";
+	model = "BCM21664 Garnet board";
+	compatible = "brcm,bcm21664-garnet", "brcm,bcm21664";
 
 	memory {
 		reg = <0x80000000 0x40000000>; /* 1 GB */
@@ -40,7 +42,7 @@ sdio2: sdio@3f190000 {
 
 	sdio4: sdio@3f1b0000 {
 		max-frequency = <48000000>;
-		cd-gpios = <&gpio 14 0>;
+		cd-gpios = <&gpio 91 GPIO_ACTIVE_LOW>;
 		status = "okay";
 	};
 

arch/arm/boot/dts/bcm21664.dtsi

+/*
+ * Copyright (C) 2014 Broadcom Corporation
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation version 2.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+#include "skeleton.dtsi"
+
+/ {
+	model = "BCM21664 SoC";
+	compatible = "brcm,bcm21664";
+	interrupt-parent = <&gic>;
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+	};
+
+	gic: interrupt-controller@3ff00100 {
+		compatible = "arm,cortex-a9-gic";
+		#interrupt-cells = <3>;
+		#address-cells = <0>;
+		interrupt-controller;
+		reg = <0x3ff01000 0x1000>,
+		      <0x3ff00100 0x100>;
+	};
+
+	smc@0x3404e000 {
+		compatible = "brcm,bcm21664-smc", "brcm,kona-smc";
+		reg = <0x3404e000 0x400>; /* 1 KiB in SRAM */
+	};
+
+	uart@3e000000 {
+		compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart";
+		status = "disabled";
+		reg = <0x3e000000 0x118>;
+		clocks = <&uartb_clk>;
+		interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+	};
+
+	uart@3e001000 {
+		compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart";
+		status = "disabled";
+		reg = <0x3e001000 0x118>;
+		clocks = <&uartb2_clk>;
+		interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+	};
+
+	uart@3e002000 {
+		compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart";
+		status = "disabled";
+		reg = <0x3e002000 0x118>;
+		clocks = <&uartb3_clk>;
+		interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+	};
+
+	L2: l2-cache {
+		compatible = "arm,pl310-cache";
+		reg = <0x3ff20000 0x1000>;
+		cache-unified;
+		cache-level = <2>;
+	};
+
+	brcm,resetmgr@35001f00 {
+		compatible = "brcm,bcm21664-resetmgr";
+		reg = <0x35001f00 0x24>;
+	};
+
+	timer@35006000 {
+		compatible = "brcm,kona-timer";
+		reg = <0x35006000 0x1c>;
+		interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&hub_timer_clk>;
+	};
+
+	gpio: gpio@35003000 {
+		compatible = "brcm,bcm21664-gpio", "brcm,kona-gpio";
+		reg = <0x35003000 0x524>;
+		interrupts =
+		       <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH
+			GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		interrupt-controller;
+	};
+
+	sdio1: sdio@3f180000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f180000 0x801c>;
+		interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&sdio1_clk>;
+		status = "disabled";
+	};
+
+	sdio2: sdio@3f190000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f190000 0x801c>;
+		interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&sdio2_clk>;
+		status = "disabled";
+	};
+
+	sdio3: sdio@3f1a0000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f1a0000 0x801c>;
+		interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&sdio3_clk>;
+		status = "disabled";
+	};
+
+	sdio4: sdio@3f1b0000 {
+		compatible = "brcm,kona-sdhci";
+		reg = <0x3f1b0000 0x801c>;
+		interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&sdio4_clk>;
+		status = "disabled";
+	};
+
+	i2c@3e016000 {
+		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+		reg = <0x3e016000 0x70>;
+		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bsc1_clk>;
+		status = "disabled";
+	};
+
+	i2c@3e017000 {
+		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+		reg = <0x3e017000 0x70>;
+		interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bsc2_clk>;
+		status = "disabled";
+	};
+
+	i2c@3e018000 {
+		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+		reg = <0x3e018000 0x70>;
+		interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bsc3_clk>;
+		status = "disabled";
+	};
+
+	i2c@3e01c000 {
+		compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c";
+		reg = <0x3e01c000 0x70>;
+		interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		clocks = <&bsc4_clk>;
+		status = "disabled";
+	};
+
+	clocks {
+		bsc1_clk: bsc1 {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		bsc2_clk: bsc2 {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		bsc3_clk: bsc3 {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		bsc4_clk: bsc4 {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		pmu_bsc_clk: pmu_bsc {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		hub_timer_clk: hub_timer {
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+			#clock-cells = <0>;
+		};
+
+		pwm_clk: pwm {
+			compatible = "fixed-clock";
+			clock-frequency = <26000000>;
+			#clock-cells = <0>;
+		};
+
+		sdio1_clk: sdio1 {
+			compatible = "fixed-clock";
+			clock-frequency = <48000000>;
+			#clock-cells = <0>;
+		};
+
+		sdio2_clk: sdio2 {
+			compatible = "fixed-clock";
+			clock-frequency = <48000000>;
+			#clock-cells = <0>;
+		};
+
+		sdio3_clk: sdio3 {
+			compatible = "fixed-clock";
+			clock-frequency = <48000000>;
+			#clock-cells = <0>;
+		};
+
+		sdio4_clk: sdio4 {
+			compatible = "fixed-clock";
+			clock-frequency = <48000000>;
+			#clock-cells = <0>;
+		};
+
+		tmon_1m_clk: tmon_1m {
+			compatible = "fixed-clock";
+			clock-frequency = <1000000>;
+			#clock-cells = <0>;
+		};
+
+		uartb_clk: uartb {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		uartb2_clk: uartb2 {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		uartb3_clk: uartb3 {
+			compatible = "fixed-clock";
+			clock-frequency = <13000000>;
+			#clock-cells = <0>;
+		};
+
+		usb_otg_ahb_clk: usb_otg_ahb {
+			compatible = "fixed-clock";
+			clock-frequency = <52000000>;
+			#clock-cells = <0>;
+		};
+	};
+
+	usbotg: usb@3f120000 {
+		compatible = "snps,dwc2";
+		reg = <0x3f120000 0x10000>;
+		interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&usb_otg_ahb_clk>;
+		clock-names = "otg";
+		phys = <&usbphy>;
+		phy-names = "usb2-phy";
+		status = "disabled";
+	};
+
+	usbphy: usb-phy@3f130000 {
+		compatible = "brcm,kona-usb2-phy";
+		reg = <0x3f130000 0x28>;
+		#phy-cells = <0>;
+		status = "disabled";
+	};
+};

arch/arm/boot/dts/bcm28155-ap.dts

@@ -46,27 +46,32 @@ i2c@3e018000 {
 
 	i2c@3500d000 {
 		status="okay";
-		clock-frequency = <400000>;
-	};
+		clock-frequency = <100000>;
 
-	sdio1: sdio@3f180000 {
-		max-frequency = <48000000>;
-		status = "okay";
+		pmu: pmu@8 {
+			reg = <0x08>;
+		};
 	};
 
 	sdio2: sdio@3f190000 {
 		non-removable;
 		max-frequency = <48000000>;
+		vmmc-supply = <&camldo1_reg>;
+		vqmmc-supply = <&iosr1_reg>;
 		status = "okay";
 	};
 
 	sdio4: sdio@3f1b0000 {
 		max-frequency = <48000000>;
 		cd-gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+		vmmc-supply = <&sdldo_reg>;
+		vqmmc-supply = <&sdxldo_reg>;
 		status = "okay";
 	};
 
 	usbotg: usb@3f120000 {
+		vusb_d-supply = <&usbldo_reg>;
+		vusb_a-supply = <&iosr1_reg>;
 		status = "okay";
 	};
 
@@ -74,3 +79,39 @@ usbphy: usb-phy@3f130000 {
 		status = "okay";
 	};
 };
+
+#include "bcm59056.dtsi"
+
+&pmu {
+	compatible = "brcm,bcm59056";
+	interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+	regulators {
+		camldo1_reg: camldo1 {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		sdldo_reg: sdldo {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		sdxldo_reg: sdxldo {
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		usbldo_reg: usbldo {
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+
+		iosr1_reg: iosr1 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+	};
+};

arch/arm/boot/dts/bcm4708-netgear-r6250.dts

+/*
+ * Broadcom BCM470X / BCM5301X arm platform code.
+ * DTS for Netgear R6250 V1
+ *
+ * Copyright 2013 Hauke Mehrtens <hauke@hauke-m.de>
+ *
+ * Licensed under the GNU/GPL. See COPYING for details.
+ */
+
+/dts-v1/;
+
+#include "bcm4708.dtsi"
+
+/ {
+	compatible = "netgear,r6250v1", "brcm,bcm4708";
+	model = "Netgear R6250 V1 (BCM4708)";
+
+	chosen {
+		bootargs = "console=ttyS0,115200";
+	};
+
+	memory {
+		reg = <0x00000000 0x08000000>;
+	};
+
+	chipcommonA {
+		uart0: serial@0300 {
+			status = "okay";
+		};
+
+		uart1: serial@0400 {
+			status = "okay";
+		};
+	};
+};

arch/arm/boot/dts/efm32gg-dk3750.dts

@@ -26,7 +26,7 @@ adc@40002000 {
 		};
 
 		i2c@4000a000 {
-			location = <3>;
+			efm32,location = <3>;
 			status = "ok";
 
 			temp@48 {