ARM: dts: sunxi: h3-h5: remove mmc0 card detection pin from pinctrl

The GPIO card detection pin (mmc0_cd_pin) is already requested and
configured by mmc_gpiod_request_cd() in drivers/mmc/core/slot-gpio.c
so pinctrl is not needed.
Signed-off-by: Joonas Kylmälä <joonas.kylmala@iki.fi>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>

arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts

@@ -137,7 +137,7 @@ &ir {
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */

arch/arm/boot/dts/sun8i-h3-beelink-x2.dts

@@ -116,7 +116,7 @@ &ir {
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */

arch/arm/boot/dts/sun8i-h3-nanopi-neo-air.dts

@@ -81,7 +81,7 @@ wifi_pwrseq: wifi_pwrseq {
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */

arch/arm/boot/dts/sun8i-h3-nanopi.dtsi

@@ -97,7 +97,7 @@ &mmc0 {
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&mmc0_pins_a>;
 	status = "okay";
 	vmmc-supply = <&reg_vcc3v3>;
 };

arch/arm/boot/dts/sun8i-h3-orangepi-2.dts

@@ -133,7 +133,7 @@ &ir {
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */

arch/arm/boot/dts/sun8i-h3-orangepi-lite.dts

@@ -107,7 +107,7 @@ &ir {
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */

arch/arm/boot/dts/sun8i-h3-orangepi-one.dts

@@ -107,7 +107,7 @@ &emac {
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */

arch/arm/boot/dts/sun8i-h3-orangepi-pc.dts

@@ -129,7 +129,7 @@ &ir {
 
 &mmc0 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	pinctrl-0 = <&mmc0_pins_a>;
 	vmmc-supply = <&reg_vcc3v3>;
 	bus-width = <4>;
 	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */

arch/arm/boot/dts/sunxi-h3-h5.dtsi

@@ -356,12 +356,6 @@ mmc0_pins_a: mmc0 {
 				bias-pull-up;
 			};
 
-			mmc0_cd_pin: mmc0_cd_pin {
-				pins = "PF6";
-				function = "gpio_in";
-				bias-pull-up;
-			};
-
 			mmc1_pins_a: mmc1 {
 				pins = "PG0", "PG1", "PG2", "PG3",
 				       "PG4", "PG5";