net: phy: marvell10g: add all MACTYPE definitions for 88X33x0

Add all MACTYPE definitions for 88X3310, 88X3310P, 88X3340 and 88X3340P.

In order to have consistent naming, rename
MV_V2_33X0_PORT_CTRL_MACTYPE_RATE_MATCH to
MV_V2_33X0_PORT_CTRL_MACTYPE_10GBASER_RATE_MATCH.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/phy/marvell10g.c

@@ -78,10 +78,18 @@ enum {
 
 	/* Vendor2 MMD registers */
 	MV_V2_PORT_CTRL		= 0xf001,
-	MV_V2_PORT_CTRL_PWRDOWN			= BIT(11),
-	MV_V2_33X0_PORT_CTRL_SWRST		= BIT(15),
-	MV_V2_33X0_PORT_CTRL_MACTYPE_MASK	= 0x7,
-	MV_V2_33X0_PORT_CTRL_MACTYPE_RATE_MATCH	= 0x6,
+	MV_V2_PORT_CTRL_PWRDOWN					= BIT(11),
+	MV_V2_33X0_PORT_CTRL_SWRST				= BIT(15),
+	MV_V2_33X0_PORT_CTRL_MACTYPE_MASK			= 0x7,
+	MV_V2_33X0_PORT_CTRL_MACTYPE_RXAUI			= 0x0,
+	MV_V2_3310_PORT_CTRL_MACTYPE_XAUI_RATE_MATCH		= 0x1,
+	MV_V2_3340_PORT_CTRL_MACTYPE_RXAUI_NO_SGMII_AN		= 0x1,
+	MV_V2_33X0_PORT_CTRL_MACTYPE_RXAUI_RATE_MATCH		= 0x2,
+	MV_V2_3310_PORT_CTRL_MACTYPE_XAUI			= 0x3,
+	MV_V2_33X0_PORT_CTRL_MACTYPE_10GBASER			= 0x4,
+	MV_V2_33X0_PORT_CTRL_MACTYPE_10GBASER_NO_SGMII_AN	= 0x5,
+	MV_V2_33X0_PORT_CTRL_MACTYPE_10GBASER_RATE_MATCH	= 0x6,
+	MV_V2_33X0_PORT_CTRL_MACTYPE_USXGMII			= 0x7,
 	/* Temperature control/read registers (88X3310 only) */
 	MV_V2_TEMP_CTRL		= 0xf08a,
 	MV_V2_TEMP_CTRL_MASK	= 0xc000,
@@ -480,7 +488,7 @@ static int mv3310_config_init(struct phy_device *phydev)
 	if (val < 0)
 		return val;
 	priv->rate_match = ((val & MV_V2_33X0_PORT_CTRL_MACTYPE_MASK) ==
-			MV_V2_33X0_PORT_CTRL_MACTYPE_RATE_MATCH);
+			MV_V2_33X0_PORT_CTRL_MACTYPE_10GBASER_RATE_MATCH);
 
 	/* Enable EDPD mode - saving 600mW */
 	return mv3310_set_edpd(phydev, ETHTOOL_PHY_EDPD_DFLT_TX_MSECS);