arm64: dts: qcom: sm8550-qrd: add display and panel

Enable Display Subsystem with Visionox VTDR6130 Panel (same as on
MTP8550).
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230516154539.238655-3-krzysztof.kozlowski@linaro.org

arch/arm64/boot/dts/qcom/sm8550-qrd.dts

@@ -431,6 +431,46 @@ &gcc {
 		 <&usb_dp_qmpphy QMP_USB43DP_USB3_PIPE_CLK>;
 };
 
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l3e_1p2>;
+	status = "okay";
+
+	panel@0 {
+		compatible = "visionox,vtdr6130";
+		reg = <0>;
+
+		pinctrl-0 = <&sde_dsi_active>, <&sde_te_active>;
+		pinctrl-1 = <&sde_dsi_suspend>, <&sde_te_suspend>;
+		pinctrl-names = "default", "sleep";
+
+		vci-supply = <&vreg_l13b_3p0>;
+		vdd-supply = <&vreg_l11b_1p2>;
+		vddio-supply = <&vreg_l12b_1p8>;
+
+		reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+
+		port {
+			panel0_in: endpoint {
+				remote-endpoint = <&mdss_dsi0_out>;
+			};
+		};
+	};
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&panel0_in>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vreg_l1e_0p88>;
+	status = "okay";
+};
+
 &pcie_1_phy_aux_clk {
 	status = "disabled";
 };
@@ -532,6 +572,34 @@ wcd_tx: codec@0,3 {
 &tlmm {
 	gpio-reserved-ranges = <32 8>;
 
+	sde_dsi_active: sde-dsi-active-state {
+		pins = "gpio133";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	sde_dsi_suspend: sde-dsi-suspend-state {
+		pins = "gpio133";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	sde_te_active: sde-te-active-state {
+		pins = "gpio86";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	sde_te_suspend: sde-te-suspend-state {
+		pins = "gpio86";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
 	wcd_default: wcd-reset-n-active-state {
 		pins = "gpio108";
 		function = "gpio";