Merge branch 'ib-meson-fixes' into devel

Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt

@@ -23,11 +23,11 @@ The GPIO bank for the controller is represented as a sub-node and it acts as a
 GPIO controller.
 
 Required properties for sub-nodes are:
- - reg: should contain address and size for mux, pull-enable, pull and
-   gpio register sets
- - reg-names: an array of strings describing the "reg" entries. Must
-   contain "mux", "pull" and "gpio". "pull-enable" is optional and
-   when it is missing the "pull" registers are used instead
+ - reg: should contain a list of address and size, one tuple for each entry
+   in reg-names.
+ - reg-names: an array of strings describing the "reg" entries.
+   Must contain "mux" and "gpio".
+   May contain "pull", "pull-enable" and "ds" when appropriate.
  - gpio-controller: identifies the node as a gpio controller
  - #gpio-cells: must be 2
 

drivers/pinctrl/meson/pinctrl-meson.c

@@ -31,6 +31,9 @@
  * In some cases the register ranges for pull enable and pull
  * direction are the same and thus there are only 3 register ranges.
  *
+ * Since Meson G12A SoC, the ao register ranges for gpio, pull enable
+ * and pull direction are the same, so there are only 2 register ranges.
+ *
  * For the pull and GPIO configuration every bank uses a contiguous
  * set of bits in the register sets described above; the same register
  * can be shared by more banks with different offsets.
@@ -488,21 +491,26 @@ static int meson_pinctrl_parse_dt(struct meson_pinctrl *pc,
 		return PTR_ERR(pc->reg_mux);
 	}
 
-	pc->reg_pull = meson_map_resource(pc, gpio_np, "pull");
-	if (IS_ERR(pc->reg_pull)) {
-		dev_err(pc->dev, "pull registers not found\n");
-		return PTR_ERR(pc->reg_pull);
+	pc->reg_gpio = meson_map_resource(pc, gpio_np, "gpio");
+	if (IS_ERR(pc->reg_gpio)) {
+		dev_err(pc->dev, "gpio registers not found\n");
+		return PTR_ERR(pc->reg_gpio);
 	}
 
+	pc->reg_pull = meson_map_resource(pc, gpio_np, "pull");
+	/* Use gpio region if pull one is not present */
+	if (IS_ERR(pc->reg_pull))
+		pc->reg_pull = pc->reg_gpio;
+
 	pc->reg_pullen = meson_map_resource(pc, gpio_np, "pull-enable");
 	/* Use pull region if pull-enable one is not present */
 	if (IS_ERR(pc->reg_pullen))
 		pc->reg_pullen = pc->reg_pull;
 
-	pc->reg_gpio = meson_map_resource(pc, gpio_np, "gpio");
-	if (IS_ERR(pc->reg_gpio)) {
-		dev_err(pc->dev, "gpio registers not found\n");
-		return PTR_ERR(pc->reg_gpio);
+	pc->reg_ds = meson_map_resource(pc, gpio_np, "ds");
+	if (IS_ERR(pc->reg_ds)) {
+		dev_dbg(pc->dev, "ds registers not found - skipping\n");
+		pc->reg_ds = NULL;
 	}
 
 	return 0;

drivers/pinctrl/meson/pinctrl-meson.h

@@ -120,6 +120,7 @@ struct meson_pinctrl {
 	struct regmap *reg_pullen;
 	struct regmap *reg_pull;
 	struct regmap *reg_gpio;
+	struct regmap *reg_ds;
 	struct gpio_chip chip;
 	struct device_node *of_node;
 };