Commit fea34091 authored by Alan Stern's avatar Alan Stern Committed by Greg Kroah-Hartman

USB: add direction bit to urb->transfer_flags

This patch (as945) adds a bit to urb->transfer_flags for recording the
direction of the URB.  The bit is set/cleared automatically in
usb_submit_urb() so drivers don't have to worry about it (although as
a result, it isn't valid until the URB has been submitted).  Inline
routines are added for easily checking an URB's direction.  They
replace calls to usb_pipein in the DMA-mapping parts of hcd.c.

For non-control endpoints, the direction is determined directly from
the endpoint descriptor.  However control endpoints are
bi-directional; for them the direction is determined from the
bRequestType byte and the wLength value in the setup packet.
Signed-off-by: default avatarAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@suse.de>
parent bdd016ba
......@@ -928,7 +928,7 @@ static void urb_unlink(struct usb_hcd *hcd, struct urb *urb)
dma_unmap_single (hcd->self.controller,
urb->transfer_dma,
urb->transfer_buffer_length,
usb_pipein (urb->pipe)
usb_urb_dir_in(urb)
? DMA_FROM_DEVICE
: DMA_TO_DEVICE);
}
......@@ -1014,7 +1014,7 @@ int usb_hcd_submit_urb (struct urb *urb, gfp_t mem_flags)
hcd->self.controller,
urb->transfer_buffer,
urb->transfer_buffer_length,
usb_pipein (urb->pipe)
usb_urb_dir_in(urb)
? DMA_FROM_DEVICE
: DMA_TO_DEVICE);
}
......
......@@ -309,7 +309,21 @@ int usb_submit_urb(struct urb *urb, gfp_t mem_flags)
* and don't need to duplicate tests
*/
xfertype = usb_endpoint_type(&ep->desc);
is_out = usb_pipeout(urb->pipe);
if (xfertype == USB_ENDPOINT_XFER_CONTROL) {
struct usb_ctrlrequest *setup =
(struct usb_ctrlrequest *) urb->setup_packet;
if (!setup)
return -ENOEXEC;
is_out = !(setup->bRequestType & USB_DIR_IN) ||
!setup->wLength;
} else {
is_out = usb_endpoint_dir_out(&ep->desc);
}
/* Cache the direction for later use */
urb->transfer_flags = (urb->transfer_flags & ~URB_DIR_MASK) |
(is_out ? URB_DIR_OUT : URB_DIR_IN);
if (xfertype != USB_ENDPOINT_XFER_CONTROL &&
dev->state < USB_STATE_CONFIGURED)
......@@ -363,7 +377,7 @@ int usb_submit_urb(struct urb *urb, gfp_t mem_flags)
/* enforce simple/standard policy */
allowed = (URB_NO_TRANSFER_DMA_MAP | URB_NO_SETUP_DMA_MAP |
URB_NO_INTERRUPT);
URB_NO_INTERRUPT | URB_DIR_MASK);
switch (xfertype) {
case USB_ENDPOINT_XFER_BULK:
if (is_out)
......
......@@ -1021,6 +1021,8 @@ extern int usb_disabled(void);
/*
* urb->transfer_flags:
*
* Note: URB_DIR_IN/OUT is automatically set in usb_submit_urb().
*/
#define URB_SHORT_NOT_OK 0x0001 /* report short reads as errors */
#define URB_ISO_ASAP 0x0002 /* iso-only, urb->start_frame
......@@ -1033,6 +1035,10 @@ extern int usb_disabled(void);
* needed */
#define URB_FREE_BUFFER 0x0100 /* Free transfer buffer with the URB */
#define URB_DIR_IN 0x0200 /* Transfer from device to host */
#define URB_DIR_OUT 0
#define URB_DIR_MASK URB_DIR_IN
struct usb_iso_packet_descriptor {
unsigned int offset;
unsigned int length; /* expected length */
......@@ -1380,6 +1386,30 @@ extern void usb_unanchor_urb(struct urb *urb);
extern int usb_wait_anchor_empty_timeout(struct usb_anchor *anchor,
unsigned int timeout);
/**
* usb_urb_dir_in - check if an URB describes an IN transfer
* @urb: URB to be checked
*
* Returns 1 if @urb describes an IN transfer (device-to-host),
* otherwise 0.
*/
static inline int usb_urb_dir_in(struct urb *urb)
{
return (urb->transfer_flags & URB_DIR_MASK) != URB_DIR_OUT;
}
/**
* usb_urb_dir_out - check if an URB describes an OUT transfer
* @urb: URB to be checked
*
* Returns 1 if @urb describes an OUT transfer (host-to-device),
* otherwise 0.
*/
static inline int usb_urb_dir_out(struct urb *urb)
{
return (urb->transfer_flags & URB_DIR_MASK) == URB_DIR_OUT;
}
void *usb_buffer_alloc (struct usb_device *dev, size_t size,
gfp_t mem_flags, dma_addr_t *dma);
void usb_buffer_free (struct usb_device *dev, size_t size,
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment