net: phy: marvell: Use the set_polarity helper

Some of the init functions unilaterally enable set auto cross over
without using the helper. Make use of the helper, and respect the
phydev MDI configuration.

Clean up the #define used while setting polarity, and the other
functions of the bits in the register.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/phy/marvell.c

@@ -55,10 +55,12 @@
 #define MII_M1011_IMASK_INIT		0x6400
 #define MII_M1011_IMASK_CLEAR		0x0000
 
-#define MII_M1011_PHY_SCR		0x10
-#define MII_M1011_PHY_SCR_MDI		0x0000
-#define MII_M1011_PHY_SCR_MDI_X		0x0020
-#define MII_M1011_PHY_SCR_AUTO_CROSS	0x0060
+#define MII_M1011_PHY_SCR			0x10
+#define MII_M1011_PHY_SCR_DOWNSHIFT_EN		BIT(11)
+#define MII_M1011_PHY_SCR_DOWNSHIFT_SHIFT	12
+#define MII_M1011_PHY_SCR_MDI			(0x0 << 5)
+#define MII_M1011_PHY_SCR_MDI_X			(0x1 << 5)
+#define MII_M1011_PHY_SCR_AUTO_CROSS		(0x3 << 5)
 
 #define MII_M1111_PHY_LED_CONTROL	0x18
 #define MII_M1111_PHY_LED_DIRECT	0x4100
@@ -486,8 +488,7 @@ static int m88e1121_config_aneg(struct phy_device *phydev)
 	if (err < 0)
 		return err;
 
-	err = phy_write(phydev, MII_M1011_PHY_SCR,
-			MII_M1011_PHY_SCR_AUTO_CROSS);
+	err = marvell_set_polarity(phydev, phydev->mdix_ctrl);
 	if (err < 0)
 		return err;
 
@@ -655,10 +656,13 @@ static int m88e1116r_config_init(struct phy_device *phydev)
 	if (err < 0)
 		return err;
 
+	err = marvell_set_polarity(phydev, phydev->mdix_ctrl);
+	if (err < 0)
+		return err;
+
 	temp = phy_read(phydev, MII_M1011_PHY_SCR);
-	temp |= (7 << 12);	/* max number of gigabit attempts */
-	temp |= (1 << 11);	/* enable downshift */
-	temp |= MII_M1011_PHY_SCR_AUTO_CROSS;
+	temp |= (7 << MII_M1011_PHY_SCR_DOWNSHIFT_SHIFT);
+	temp |= MII_M1011_PHY_SCR_DOWNSHIFT_EN;
 	err = phy_write(phydev, MII_M1011_PHY_SCR, temp);
 	if (err < 0)
 		return err;
@@ -891,8 +895,7 @@ static int m88e1118_config_aneg(struct phy_device *phydev)
 	if (err < 0)
 		return err;
 
-	err = phy_write(phydev, MII_M1011_PHY_SCR,
-			MII_M1011_PHY_SCR_AUTO_CROSS);
+	err = marvell_set_polarity(phydev, phydev->mdix_ctrl);
 	if (err < 0)
 		return err;