Commit fecf27a3 authored by Peter Hung's avatar Peter Hung Committed by Greg Kroah-Hartman

serial: 8250_pci: add RS485 for F81504/508/512

Add RS485 control for Fintek F81504/508/512

F81504/508/512 can control their RTS with H/W mode.
PCI configuration space for each port is 0x40 + idx * 8 + 7.

When it set with 0x01, it's configured with RS232 mode.
RTS is controlled by MCR.

When it set with 0x11, it's configured with RS485 mode.
RTS is controlled by H/W, RTS low with idle & RX, high with TX.

When it set with 0x31, it's configured with RS485 mode.
RTS is controlled by H/W, RTS high with idle & RX, low with TX.

We will force 0x01 on pci_fintek_setup().
Signed-off-by: default avatarPeter Hung <hpeter+linux_kernel@gmail.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
parent a3a10ce3
......@@ -1685,11 +1685,60 @@ pci_brcm_trumanage_setup(struct serial_private *priv,
return ret;
}
/* RTS will control by MCR if this bit is 0 */
#define FINTEK_RTS_CONTROL_BY_HW BIT(4)
/* only worked with FINTEK_RTS_CONTROL_BY_HW on */
#define FINTEK_RTS_INVERT BIT(5)
/* We should do proper H/W transceiver setting before change to RS485 mode */
static int pci_fintek_rs485_config(struct uart_port *port,
struct serial_rs485 *rs485)
{
u8 setting;
u8 *index = (u8 *) port->private_data;
struct pci_dev *pci_dev = container_of(port->dev, struct pci_dev,
dev);
pci_read_config_byte(pci_dev, 0x40 + 8 * *index + 7, &setting);
if (rs485->flags & SER_RS485_ENABLED)
memset(rs485->padding, 0, sizeof(rs485->padding));
else
memset(rs485, 0, sizeof(*rs485));
/* F81504/508/512 not support RTS delay before or after send */
rs485->flags &= SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND;
if (rs485->flags & SER_RS485_ENABLED) {
/* Enable RTS H/W control mode */
setting |= FINTEK_RTS_CONTROL_BY_HW;
if (rs485->flags & SER_RS485_RTS_ON_SEND) {
/* RTS driving high on TX */
setting &= ~FINTEK_RTS_INVERT;
} else {
/* RTS driving low on TX */
setting |= FINTEK_RTS_INVERT;
}
rs485->delay_rts_after_send = 0;
rs485->delay_rts_before_send = 0;
} else {
/* Disable RTS H/W control mode */
setting &= ~(FINTEK_RTS_CONTROL_BY_HW | FINTEK_RTS_INVERT);
}
pci_write_config_byte(pci_dev, 0x40 + 8 * *index + 7, setting);
port->rs485 = *rs485;
return 0;
}
static int pci_fintek_setup(struct serial_private *priv,
const struct pciserial_board *board,
struct uart_8250_port *port, int idx)
{
struct pci_dev *pdev = priv->dev;
u8 *data;
u8 config_base;
u16 iobase;
......@@ -1702,6 +1751,15 @@ static int pci_fintek_setup(struct serial_private *priv,
port->port.iotype = UPIO_PORT;
port->port.iobase = iobase;
port->port.rs485_config = pci_fintek_rs485_config;
data = devm_kzalloc(&pdev->dev, sizeof(u8), GFP_KERNEL);
if (!data)
return -ENOMEM;
/* preserve index in PCI configuration space */
*data = idx;
port->port.private_data = data;
return 0;
}
......@@ -1752,6 +1810,9 @@ static int pci_fintek_init(struct pci_dev *dev)
(u8)((iobase & 0xff00) >> 8));
pci_write_config_byte(dev, config_base + 0x06, dev->irq);
/* force init to RS232 Mode */
pci_write_config_byte(dev, config_base + 0x07, 0x01);
}
return max_port;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment