Merge branch 'be2net-next'

Suresh Reddy says:

====================
be2net: patch-set

Hi Dave, Please consider applying these two patches to net-next
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/emulex/benet/be.h

@@ -37,7 +37,7 @@
 #include "be_hw.h"
 #include "be_roce.h"
 
-#define DRV_VER			"11.1.0.0"
+#define DRV_VER			"11.4.0.0"
 #define DRV_NAME		"be2net"
 #define BE_NAME			"Emulex BladeEngine2"
 #define BE3_NAME		"Emulex BladeEngine3"

drivers/net/ethernet/emulex/benet/be_hw.h

@@ -49,6 +49,9 @@
 #define POST_STAGE_BE_RESET		0x3 /* Host wants to reset chip */
 #define POST_STAGE_ARMFW_RDY		0xc000	/* FW is done with POST */
 #define POST_STAGE_RECOVERABLE_ERR	0xE000	/* Recoverable err detected */
+/* FW has detected a UE and is dumping FAT log data */
+#define POST_STAGE_FAT_LOG_START       0x0D00
+#define POST_STAGE_ARMFW_UE            0xF000  /*FW has asserted an UE*/
 
 /* Lancer SLIPORT registers */
 #define SLIPORT_STATUS_OFFSET		0x404

drivers/net/ethernet/emulex/benet/be_main.c

@@ -3241,8 +3241,9 @@ void be_detect_error(struct be_adapter *adapter)
 {
 	u32 ue_lo = 0, ue_hi = 0, ue_lo_mask = 0, ue_hi_mask = 0;
 	u32 sliport_status = 0, sliport_err1 = 0, sliport_err2 = 0;
-	u32 i;
 	struct device *dev = &adapter->pdev->dev;
+	u16 val;
+	u32 i;
 
 	if (be_check_error(adapter, BE_ERROR_HW))
 		return;
@@ -3280,15 +3281,25 @@ void be_detect_error(struct be_adapter *adapter)
 		ue_lo = (ue_lo & ~ue_lo_mask);
 		ue_hi = (ue_hi & ~ue_hi_mask);
 
-		/* On certain platforms BE hardware can indicate spurious UEs.
-		 * Allow HW to stop working completely in case of a real UE.
-		 * Hence not setting the hw_error for UE detection.
-		 */
-
 		if (ue_lo || ue_hi) {
+			/* On certain platforms BE3 hardware can indicate
+			 * spurious UEs. In case of a UE in the chip,
+			 * the POST register correctly reports either a
+			 * FAT_LOG_START state (FW is currently dumping
+			 * FAT log data) or a ARMFW_UE state. Check for the
+			 * above states to ascertain if the UE is valid or not.
+			 */
+			if (BE3_chip(adapter)) {
+				val = be_POST_stage_get(adapter);
+				if ((val & POST_STAGE_FAT_LOG_START)
+				     != POST_STAGE_FAT_LOG_START &&
+				    (val & POST_STAGE_ARMFW_UE)
+				     != POST_STAGE_ARMFW_UE)
+					return;
+			}
+
 			dev_err(dev, "Error detected in the adapter");
-			if (skyhawk_chip(adapter))
-				be_set_error(adapter, BE_ERROR_UE);
+			be_set_error(adapter, BE_ERROR_UE);
 
 			for (i = 0; ue_lo; ue_lo >>= 1, i++) {
 				if (ue_lo & 1)