Commit ff846f52 authored by Alexander Duyck's avatar Alexander Duyck Committed by David S. Miller

igb: add support for reporting 5GT/s during probe on PCIe Gen2

This change corrects the fact that we were not reporting Gen2 link speeds
when we were in fact connected at Gen2 rates.
Signed-off-by: default avatarAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent ef021194
......@@ -610,11 +610,7 @@
#define IGP_LED3_MODE 0x07000000
/* PCI/PCI-X/PCI-EX Config space */
#define PCIE_LINK_STATUS 0x12
#define PCIE_DEVICE_CONTROL2 0x28
#define PCIE_LINK_WIDTH_MASK 0x3F0
#define PCIE_LINK_WIDTH_SHIFT 4
#define PCIE_DEVICE_CONTROL2_16ms 0x0005
#define PHY_REVISION_MASK 0xFFFFFFF0
......
......@@ -53,17 +53,30 @@ s32 igb_get_bus_info_pcie(struct e1000_hw *hw)
u16 pcie_link_status;
bus->type = e1000_bus_type_pci_express;
bus->speed = e1000_bus_speed_2500;
ret_val = igb_read_pcie_cap_reg(hw,
PCIE_LINK_STATUS,
&pcie_link_status);
if (ret_val)
PCI_EXP_LNKSTA,
&pcie_link_status);
if (ret_val) {
bus->width = e1000_bus_width_unknown;
else
bus->speed = e1000_bus_speed_unknown;
} else {
switch (pcie_link_status & PCI_EXP_LNKSTA_CLS) {
case PCI_EXP_LNKSTA_CLS_2_5GB:
bus->speed = e1000_bus_speed_2500;
break;
case PCI_EXP_LNKSTA_CLS_5_0GB:
bus->speed = e1000_bus_speed_5000;
break;
default:
bus->speed = e1000_bus_speed_unknown;
break;
}
bus->width = (enum e1000_bus_width)((pcie_link_status &
PCIE_LINK_WIDTH_MASK) >>
PCIE_LINK_WIDTH_SHIFT);
PCI_EXP_LNKSTA_NLW) >>
PCI_EXP_LNKSTA_NLW_SHIFT);
}
reg = rd32(E1000_STATUS);
bus->func = (reg & E1000_STATUS_FUNC_MASK) >> E1000_STATUS_FUNC_SHIFT;
......
......@@ -1638,6 +1638,7 @@ static int __devinit igb_probe(struct pci_dev *pdev,
dev_info(&pdev->dev, "%s: (PCIe:%s:%s) %pM\n",
netdev->name,
((hw->bus.speed == e1000_bus_speed_2500) ? "2.5Gb/s" :
(hw->bus.speed == e1000_bus_speed_5000) ? "5.0Gb/s" :
"unknown"),
((hw->bus.width == e1000_bus_width_pcie_x4) ? "Width x4" :
(hw->bus.width == e1000_bus_width_pcie_x2) ? "Width x2" :
......
......@@ -442,7 +442,10 @@
#define PCI_EXP_LNKCTL_LABIE 0x0800 /* Lnk Autonomous Bandwidth Interrupt Enable */
#define PCI_EXP_LNKSTA 18 /* Link Status */
#define PCI_EXP_LNKSTA_CLS 0x000f /* Current Link Speed */
#define PCI_EXP_LNKSTA_CLS_2_5GB 0x01 /* Current Link Speed 2.5GT/s */
#define PCI_EXP_LNKSTA_CLS_5_0GB 0x02 /* Current Link Speed 5.0GT/s */
#define PCI_EXP_LNKSTA_NLW 0x03f0 /* Nogotiated Link Width */
#define PCI_EXP_LNKSTA_NLW_SHIFT 4 /* start of NLW mask in link status */
#define PCI_EXP_LNKSTA_LT 0x0800 /* Link Training */
#define PCI_EXP_LNKSTA_SLC 0x1000 /* Slot Clock Configuration */
#define PCI_EXP_LNKSTA_DLLLA 0x2000 /* Data Link Layer Link Active */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment