siimage: fix ->set_pio_mode method to select PIO data transfer

* Remember to select PIO data transfer (with IORDY monitored) in sil_tune_pio()
  (->set_pio_mode method) so the controller is always programmed correctly for
  PIO transfers (this is important if DMA is not going to be used).

* Don't set DMA/UDMA timings for PIO modes in siimage_tune_chipset().

* Bump driver version.
Acked-by: default avatarSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: default avatarBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
parent 326d72f4
/*
* linux/drivers/ide/pci/siimage.c Version 1.15 Jun 29 2007
* linux/drivers/ide/pci/siimage.c Version 1.16 Jul 13 2007
*
* Copyright (C) 2001-2002 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2003 Red Hat <alan@redhat.com>
......@@ -185,7 +185,12 @@ static void sil_tune_pio(ide_drive_t *drive, u8 pio)
u16 speedp = 0;
unsigned long addr = siimage_seldev(drive, 0x04);
unsigned long tfaddr = siimage_selreg(hwif, 0x02);
unsigned long base = (unsigned long)hwif->hwif_data;
u8 tf_pio = pio;
u8 addr_mask = hwif->channel ? (hwif->mmio ? 0xF4 : 0x84)
: (hwif->mmio ? 0xB4 : 0x80);
u8 mode = 0;
u8 unit = drive->select.b.unit;
/* trim *taskfile* PIO to the slowest of the master/slave */
if (pair->present) {
......@@ -207,6 +212,11 @@ static void sil_tune_pio(ide_drive_t *drive, u8 pio)
hwif->OUTW(hwif->INW(tfaddr-2)|0x200, tfaddr-2);
else
hwif->OUTW(hwif->INW(tfaddr-2)&~0x200, tfaddr-2);
mode = hwif->INB(base + addr_mask);
mode &= ~(unit ? 0x30 : 0x03);
mode |= (unit ? 0x10 : 0x01);
hwif->OUTB(mode, base + addr_mask);
} else {
pci_write_config_word(hwif->pci_dev, addr, speedp);
pci_write_config_word(hwif->pci_dev, tfaddr, speedt);
......@@ -216,6 +226,11 @@ static void sil_tune_pio(ide_drive_t *drive, u8 pio)
if (pio > 2)
speedp |= 0x200;
pci_write_config_word(hwif->pci_dev, tfaddr-2, speedp);
pci_read_config_byte(hwif->pci_dev, addr_mask, &mode);
mode &= ~(unit ? 0x30 : 0x03);
mode |= (unit ? 0x10 : 0x01);
pci_write_config_byte(hwif->pci_dev, addr_mask, mode);
}
}
......@@ -275,8 +290,7 @@ static int siimage_tune_chipset(ide_drive_t *drive, const u8 speed)
case XFER_PIO_1:
case XFER_PIO_0:
sil_tune_pio(drive, speed - XFER_PIO_0);
mode |= ((unit) ? 0x10 : 0x01);
break;
return ide_config_drive_speed(drive, speed);
case XFER_MW_DMA_2:
case XFER_MW_DMA_1:
case XFER_MW_DMA_0:
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment