Merge tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Enable dm814x and dra62x clock driver. This branch has a dependency
to the clk-ti branch from the Linux clk tree for the ADPLL clock driver.
Otherwise things won't keep booting properly when we flip over to use
the clock driver instead of fixed clocks set up by the bootloader.

* tag 'omap-for-v4.6/dt-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: Add clocks for dm814x ADPLL

Merge tag 'qcom-fixes-for-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into fixes

Merge "Qualcomm Fixes for v4.6-rc2" from Andy Gross:

* Revert BAM usage on MSM8974 boards

* tag 'qcom-fixes-for-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  Revert "dts: msm8974: Add dma channels for blsp2_i2c1 node"
  Revert "dts: msm8974: Add blsp2_bam dma node"

The I2C hardware blocks on this SoC are connected as follows:

  I2C0: external connection
  I2C1: external connection
  I2C2: internal connection
  I2C3: external connection
  I2C4: external connection
  I2C5: internal connection
  I2C6: no connection (not accessible)

Delete pinctrl from Ch2, add pinctrl to Ch4, and remove the Ch6 node.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'imx-fixes-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes

Merge "ARM: i.MX fixes for 4.6" from Shawn Guo:

The i.MX fixes for 4.6:
 - The sdhci-esdhc-imx DMA support is broken due to commit 7b91369b
   ("mmc: sdhci: Set DMA mask when adding host").  It requires device's
   dma_mask be set up properly to get DMA work.  The fixing patch
   initializes the DMA mask to enable the access again.

* tag 'imx-fixes-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: mach-imx: sdhci-esdhc-imx: initialize DMA mask

Merge tag 'omap-for-v4.6/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Merge "omap fixes for v4.6-rc cycle" from Tony Lindgren:

Fixes for omaps for v4.6-rc cycle:

- Clockdomain fix for dra7 timer interrupts

- Two fixes for GPMC EDMA binding, I missed the need for a merge with
  GPMC changes and EDMA changes

- Fix beagle-x15 eSATA by dropping misconfigured extcon_usb1

- Fix occasional external aborts on 36xx with PM that we've been
  chasing for past few months. It turned out to be duplicate restore
  of INTC registers that can in some cases cause us to hit erratum 1.106.

* tag 'omap-for-v4.6/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP3: Fix external abort on 36xx waking from off mode idle
  ARM: dts: am57xx-beagle-x15: remove extcon_usb1
  ARM: dts: am437x: Fix GPMC dma properties
  ARM: dts: am33xx: Fix GPMC dma properties
  ARM: DRA7: clockdomain: Implement timer workaround for errata i874

Merge tag 'renesas-fixes-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

Merge "Renesas ARM Based SoC Fixes for v4.6" from Simon Horman:

Renesas ARM Based SoC Fixes for v4.6

* Correct preset_lpj calculation which may lead to too short delays
* Correct handling of optional clocks on r8a7791 to restore
  access to the serial port the porter board

* tag 'renesas-fixes-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: timer: Fix preset_lpj leading to too short delays
  Revert "ARM: dts: porter: Enable SCIF_CLK frequency and pins"
  ARM: dts: r8a7791: Don't disable referenced optional clocks

Merge tag 'omap-for-v4.6/fixes-rc2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Merge "omap fixes against v4.6-rc2" from Tony Lindgren

Fixes for omaps against v4.6-rc2, mostly to fix suspend for beagle-x15
that broke when we added runtime based SoC revision detection earlier.

It seems suspend worked earlier as things were only partially initialized,
while now we initialize things properly for dra7.

Note that the "ARM: OMAP: Catch callers of revision information prior
to it being populated" had to be reverted as it caused bogus warnings
for other SoCs because omap initcalls bail out based on revision being
set to 0 for other SoCs. These initcalls will mostly just disappear
when we drop support for omap3 legacy booting.

Also included is a fix for dra7 sys_32k_ck clock source that is not
enabled on boot making system fall back to using emulated clock.

* tag 'omap-for-v4.6/fixes-rc2-v2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (198 commits)
  Revert "ARM: OMAP: Catch callers of revision information prior to it being populated"
  ARM: OMAP: Catch callers of revision information prior to it being populated
  ARM: dts: dra7: Correct clock tree for sys_32k_ck
  ARM: OMAP: DRA7: Provide proper class to omap2_set_globals_tap
  ARM: OMAP: DRA7: wakeupgen: Skip SAR save for wakeupgen
  Linux 4.6-rc2
  v4l2-mc: avoid warning about unused variable
  Convert straggling drivers to new six-argument get_user_pages()
  .mailmap: add Christophe Ricard
  Make CONFIG_FHANDLE default y
  mm/page_isolation.c: fix the function comments
  oom, oom_reaper: do not enqueue task if it is on the oom_reaper_list head
  mm/page_isolation: fix tracepoint to mirror check function behavior
  mm/rmap: batched invalidations should use existing api
  x86/mm: TLB_REMOTE_SEND_IPI should count pages
  mm: fix invalid node in alloc_migrate_target()
  include/linux/huge_mm.h: return NULL instead of false for pmd_trans_huge_lock()
  mm, kasan: fix compilation for CONFIG_SLAB
  MAINTAINERS: orangefs mailing list is subscribers-only
  net: mvneta: fix changing MTU when using per-cpu processing
  ...

On all shmobile ARM SoCs, loop-based delays may complete early, which
can be after only 1/3 (Cortex A9) or 1/2 (Cortex A7 or A15) of the
minimum required time.

This is caused by calculating preset_lpj based on incorrect assumptions
about the number of clock cycles per loop:
  - All of Cortex A7, A9, and A15 run __loop_delay() at 1 loop per
    CPU clock cycle,
  - As of commit 11d4bb1b ("ARM: 7907/1: lib: delay-loop: Add
    align directive to fix BogoMIPS calculation"), Cortex A8 runs
    __loop_delay() at 1 loop per 2 instead of 3 CPU clock cycles.

On SoCs with Cortex A7 and/or A15 CPU cores, this went unnoticed, as
delays use the ARM arch timer if available. R-Car Gen2 doesn't work if
the arch timer is disabled. However, APE6 can be used without the arch
timer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This reverts commit 19417bd9 ("ARM: dts: porter: Enable SCIF_CLK
frequency and pins") as according to
http://elinux.org/File:R-CarM2-KOELSCH_PORTER-B_PORTER_C_Comparison.pdf
the external oscillator for SCIF_CLK is not mounted on the porter boards.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clk_get on a disabled clock node will return EPROBE_DEFER, which can
cause drivers to be deferred forever if such clocks are referenced in
their clocks property.

Update the various disabled external clock nodes to default to a
frequency of 0, but don't disable them to prevent this.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This reverts commit 571afb4c.

- fix boot error reverting commit cc8ed769
("soc: mediatek: SCPSYS: Fix double enabling of regulators")

* tag 'v4.6-soc-fixes' of https://github.com/mbgg/linux-mediatek:
  Revert "soc: mediatek: SCPSYS: Fix double enabling of regulators"

Depending on timing during the resume path from off mode on 36xx, we may
see external aborts. These seem to be caused by the following:

- OMAP3 Advisory 1.62 "MPU Cannot Exit from Standby" says we need to
  disable intc autoidle before WFI

- DM3730 Advisory 1.106 "MPU Leaves MSTANDBY State Before IDLEREQ of
  Interrupt Controller is Released" says we need to wait before
  accessing intc

omap3_intc_resume_idle restores the intc autoidle for all resume paths,
however in the resume path from off mode only it is also being restored
by omap_intc_restore_context before this call to omap3_intc_resume_idle
happens. The second restore of the intc autoidle in this path is what
appears to be causing the external abort so for the off mode resume path
let's rely on omap_intc_restore_context to restore intc autoidle, and
for all other paths let omap3_intc_resume_idle handle it as it is now.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

USB1 controller is hardwired to be used as Host only port so
we don't need to check ID pin state and can get rid of extcon_usb1.

This also reduces USB1 controller's and so eSATA power's dependency
with EXTCON. This fixes eSATA port with multi_v7_defconfig.

Cc: Franklin S Cooper Jr. <fcooper@ti.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
[tony@atomide.com: updated to describe what it fixes]
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch updates the GPMC's DT DMA property to reflect the updated eDMA
bindings.

Fixes: cce1ee00 ("ARM: DTS: am437x: Use the new DT bindings for the eDMA3")
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch updates the GPMC's DT DMA property to reflect the updated eDMA
bindings.

Fixes: b5e50906 ("ARM: DTS: am33xx: Use the new DT bindings for the eDMA3")
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge tag 'for-v4.6-rc/omap-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v4.6/fixes

ARM: OMAP2+: clockdomain: another fix for v4.6-rc

For DRA7xx platforms, add a workaround for missed timer interrupts
that appears to be due to an integration bug (erratum i874)

Basic build, boot, and PM test logs are available here:

http://www.pwsan.com/omap/testlogs/omap-fixes-b-for-v4.6-rc/20160413020850/

(The DRA7xx board here has not yet been added into the testbed.)

This reverts commit cc8ed769
("soc: mediatek: SCPSYS: Fix double enabling of regulators") [1].

This patch fixes mt8173-evb failing boot issue. With commit [1],
genpd state will not sync to real power domain state. So some
resources such as clocks and regulators may stay in a wrong state.

There is no regulator double enabling issue on mainline kernel, so
we can refert commit [1] safely.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>

With commit 7b91369b ("mmc: sdhci: Set DMA mask when adding host")
DMA access got disabled for device drivers with zero DMA mask property.
sdhci-esdhc-imx got blocked from DMA access by this.  Hence: initialize
the DMA mask to enable access again.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

mvebu fixes for 4.6 (part 1)

- fix USB adress register for Linksys Armada 388 based boards
- fix build warning in mvebu-mbus

* tag 'mvebu-fixes-4.6-1' of git://git.infradead.org/linux-mvebu:
  ARM: mvebu: Correct unit address for linksys
  bus: mvebu-mbus: use %pa to print phys_addr_t
Signed-off-by: Olof Johansson <olof@lixom.net>

The website handhelds.org has been down for a long time and is
likely never coming back online.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

ARM: pxa: fixes for v4.6

There is only a single fix for dma requestor lines initial
setup, triggered by dmaengine previous fix.

* tag 'pxa-fixes-v4.6' of https://github.com/rjarzmik/linux:
  ARM: pxa: fix the number of DMA requestor lines
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.6/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps against v4.6-rc1. Mostly minor fixes for the newer
SoCs with few board fixes and a fix for a long time hwmod bug:

- Fix cpsw_emac0 link type for baltos-ir5221
- Fix interrupt type for TWD
- Fix edma memcpy channel allocation for am43x
- Fix am43x-epos sycntimer32k by using the correct assigned clock
- Fix interconnect barrier for dra7
- Fix a long time hwmod bug for updating sysconfig register properly
- Fix flakey booting on dm814x where USB reset needs a delay

And there is one minor change that is not strictly a fix, but is
good to have for proper hardware detection:

- Detect dra7 silicon revision 2.0 properly

* tag 'omap-for-v4.6/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am335x-baltos-ir5221: fix cpsw_emac0 link type
  ARM: OMAP: Correct interrupt type for ARM TWD
  ARM: DRA722: Add ID detect for Silicon Rev 2.0
  ARM: dts: am43xx: fix edma memcpy channel allocation
  ARM: dts: AM43x-epos: Fix clk parent for synctimer
  ARM: OMAP2: Fix up interconnect barrier initialization for DRA7
  ARM: OMAP2+: hwmod: Fix updating of sysconfig register
  ARM: OMAP2+: Use srst_udelay for USB on dm814x
Signed-off-by: Olof Johansson <olof@lixom.net>

This patch fixes condition whether the specified address ranges
overlap each other.

Fixes: 4b7f48d3 ("bus: uniphier-system-bus: add UniPhier System Bus driver")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

My intention was to ioremap a 4-byte register.  Coincidentally enough,
sizeof(SZ_4) equals to SZ_4, but this code is weird anyway.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>

Errata Title:
i874: TIMER5/6/7/8 interrupts not propagated

Description:
When TIMER5, TIMER6, TIMER7, or TIMER8 clocks are enabled
(CM_IPU_TIMER5/6/7/8_CLKCTRL[0:1]MODULEMODE=0x2:ENABLE) and the CD-IPU
is in HW_AUTO mode (CM_IPU_CLKSTCTRL[0:1]CLKTRCTRL=0x3:HW_AUTO) the
corresponding TIMER will continue counting, but enabled interrupts
will not be propagated to the destinations (MPU, DSP, etc) in the
SoC until the TIMER registers are accessed from the CPUs (MPU, DSP
etc.). This can result in missed timer interrupts.

Workaround:
In order for TIMER5/6/7/8 interrupts to be propagated and serviced
correctly the CD_IPU domain should be set to SW_WKUP mode
(CM_IPU_CLKSTCTRL[0:1]CLKTRCTRL=0x2:SW_WKUP).

The above workaround is achieved by switching the IPU clockdomain
flags from HWSUP_SWSUP to SWSUP only.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>

With http://www.spinics.net/lists/devicetree/msg116771.html we split / refactor
the pinctrl driver to have two different pinctrl devices for each bus on the
Amlogic Meson8 / Meson8b SoCs.
These are the missing patches for documentation and DT that weren't pulled into
mainline with the driver changes.

* tag 'meson8-dt-fix' of https://github.com/carlocaione/linux-meson:
  documentation: Fix pinctrl documentation for Meson8 / Meson8b
  ARM: dts: amlogic: Split pinctrl device for Meson8 / Meson8b

omap_rev is used to detect various SoC types, however any misuse of
the usage by invoking it earlier than it being populated will result
in invalid results. Lets flag them as early as possible to prevent
unintended side effects taking place. We get 0 if it is uninitialized
and -1 when detection is done using device tree (as the case was for
DRA7 as the case was prior to commit 06c2d368 ("ARM: OMAP: DRA7:
Make use of omap_revision information for soc_is* calls")
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This is w.r.t J6/J6eco: 32clk is pseudo (erratum i856) - clock source.
Errata i856 for the AM572x (DRA7xx) points out that the 32.768KHz external
crystal is not enabled at power up. Instead the CPU falls back to using
an emulation for the 32KHz clock which is SYSCLK1/610.  SYSCLK1 is usually
20MHz on boards so far (which gives an emulated frequency of 32.786KHz)

Modelling the same in device tree.
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

When commit 06c2d368 ("ARM: OMAP: DRA7: Make use of omap_revision
information for soc_is* calls") introduced SoC check using
omap_revision, it missed providing DRA7 as class for initializing
the omap_version variable. Without doing this, soc_is_dra7xx() will
fail and as a result, omap4_pm_init_early never initializes the dra7
erratum for CPU power state. This causes the suspend path to fail
on DRA7 devices.

Fixes: 06c2d368 ("ARM: OMAP: DRA7: Make use of omap_revision information for soc_is* calls")
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

DRA7 has no SAR region for automated save and restore of wakeupgen,
which does not make real since the SoC really does not do legacy OFF
mode anymore. Further wakeupgen should never loose context in CSWR
retention mode for MPU domain on DRA7 since that is the deepest state
we will enter.

So, just skip, instead of oopsing as follows while attemptint to enter
suspend on BeagleBoard-X15.
[   55.589771] Unable to handle kernel paging request at virtual address 00002684
[   55.589771] pgd = ec69c000
[...]
[   55.589771] [<c0123cc8>] (irq_notifier) from [<c015ad70>] (notifier_call_chain+0x4c/0x8c)
[   55.589771] [<c015ad70>] (notifier_call_chain) from [<c021469c>] (cpu_cluster_pm_enter+0x2c/0x78)
[   55.589771] [<c021469c>] (cpu_cluster_pm_enter) from [<c0514508>] (syscore_suspend+0xb8/0x31c)
[   55.589771] [<c0514508>] (syscore_suspend) from [<c0197d24>] (suspend_devices_and_enter+0x308/0x9e4)
[   55.589771] [<c0197d24>] (suspend_devices_and_enter) from [<c0198a40>] (pm_suspend+0x640/0x75c)
[   55.589771] [<c0198a40>] (pm_suspend) from [<c0196bcc>] (state_store+0x64/0xb8)
[   55.589771] [<c0196bcc>] (state_store) from [<c0307914>] (kernfs_fop_write+0xc0/0x1bc)
[   55.589771] [<c0307914>] (kernfs_fop_write) from [<c028ac80>] (__vfs_write+0x1c/0xd8)
[   55.589771] [<c028ac80>] (__vfs_write) from [<c028bb70>] (vfs_write+0x90/0x16c)
[   55.589771] [<c028bb70>] (vfs_write) from [<c028c890>] (SyS_write+0x44/0x9c)
[   55.589771] [<c028c890>] (SyS_write) from [<c0107840>] (ret_fast_syscall+0x0/0x1c)
[...]
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Pull perf fixes from Ingo Molnar:
 "Misc kernel side fixes:

   - fix event leak
   - fix AMD PMU driver bug
   - fix core event handling bug
   - fix build bug on certain randconfigs

  Plus misc tooling fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/amd/ibs: Fix pmu::stop() nesting
  perf/core: Don't leak event in the syscall error path
  perf/core: Fix time tracking bug with multiplexing
  perf jit: genelf makes assumptions about endian
  perf hists: Fix determination of a callchain node's childlessness
  perf tools: Add missing initialization of perf_sample.cpumode in synthesized samples
  perf tools: Fix build break on powerpc
  perf/x86: Move events_sysfs_show() outside CPU_SUP_INTEL
  perf bench: Fix detached tarball building due to missing 'perf bench memcpy' headers
  perf tests: Fix tarpkg build test error output redirection

Pull core kernel fixes from Ingo Molnar:
 "This contains the nohz/atomic cleanup/fix for the fetch_or() ugliness
  you noted during the original nohz pull request, plus there's also
  misc fixes:

   - fix liblockdep build bug
   - fix uapi header build bug
   - print more lockdep hash collision info to help debug recent reports
     of hash collisions
   - update MAINTAINERS email address"

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  MAINTAINERS: Update my email address
  locking/lockdep: Print chain_key collision information
  uapi/linux/stddef.h: Provide __always_inline to userspace headers
  tools/lib/lockdep: Fix unsupported 'basename -s' in run_tests.sh
  locking/atomic, sched: Unexport fetch_or()
  timers/nohz: Convert tick dependency mask to atomic_t
  locking/atomic: Introduce atomic_fetch_or()

Commit 840f5b05 ("media: au0828 disable tuner to demod link in
au0828_media_device_register()") removed all uses of the 'dtv_demod',
but left the variable itself around.

Remove it.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull x86 fixes from Thomas Gleixner:
 "This lot contains:

   - Some fixups for the fallout of the topology consolidation which
     unearthed AMD/Intel inconsistencies
   - Documentation for the x86 topology management
   - Support for AMD advanced power management bits
   - Two simple cleanups removing duplicated code"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Add advanced power management bits
  x86/thread_info: Merge two !__ASSEMBLY__ sections
  x86/cpufreq: Remove duplicated TDP MSR macro definitions
  x86/Documentation: Start documenting x86 topology
  x86/cpu: Get rid of compute_unit_id
  perf/x86/amd: Cleanup Fam10h NB event constraints
  x86/topology: Fix AMD core count

Revert this commit to fix regressions on non-dragonboard MSM8974 boards.
This will be put back in after the correct fixes to the bam driver are
accepted that allow remote processor control of the main control registers.

This reverts commit 0a5d0f85.
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Revert this commit to fix regressions on non-dragonboard MSM8974 boards.
This will be put back in after the correct fixes to the bam driver are
accepted that allow remote processor control of the main control registers.

This reverts commit 62bc8179.
Signed-off-by: Andy Gross <andy.gross@linaro.org>

Pull remoteproc fix from Bjorn Andersson:
 "Fix incorrect error check in the ST remoteproc driver and advertise
  the newly created linux-remoteproc mailing list"

* tag 'rproc-v4.6-rc1' of git://github.com/andersson/remoteproc:
  MAINTAINERS: Add mailing list for remote processor subsystems
  remoteproc: st: fix check of syscon_regmap_lookup_by_phandle() return value